TABLE OF CONTENTS INTRODUCTION FCC Compliance Statement ............................i Safety Instructions .............................................ii General Information.........................................1 Equipment Checklist .......................................2 Monitor Features.............................................. 3 GETTING STARTED Installation .........................................................4 Control Buttons ................................................
FCC COMPLIANCE STATEMENT ENG * Note : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against radio frequency interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy. If not installed and used in accordance with the instructions, it may cause interference to radio communications.
SAFETY INSTRUCTIONS ENG Handling Due to its fragile glass panel, this monitor must be handled with caution and not exposed to impact or shock. Never touch the display area or rub it with a hard stiff object or tool, as the panel is easily scratched. Cleaning The display area is highly prone to scratching. Do not use ketone-type cleaners (i.e. acetone), ethyl alcohol, toluene, ethyl acid or methyl chloride to clean the panel. Doing so may result in permanent damage.
SAFETY INSTRUCTIONS ENG running water for at least 15 minutes, then consult a doctor. 7. Handle this monitor with care when moving it. When lifting the monitor, support it with one hand holding the stand, and one hand holding the stand, and one hand holding the LCD screen. 8. Always disconnect the power cord when moving this monitor. 9. Do not lay this monitor in the horizontal position when operating. 10. Please use the supplied AC- Adapter for safety 11.
EQUIPMENT CHECKLIST ENG Before operating your display, please check to make sure that all of the items listed are present in your package : ◆ ◆ Color TFT LCD Monitor (With 15-pin D-SUB cable) Accessory Box : 1. AC to DC Adapter & Power Cord 2. This manual 3.Option DVI Cable S-VIDEO Cable Power Requirements The monitor is equipped with an auto-sensing power supply for voltage ranging from 100120VAC/200-240VAC, 50/60Hz. Confirm the line voltage designation then power cable to the power jack.
MONITOR FEATURES ENG ● Supports Analog IBM compatible PC, Apple Macintosh TM(Adapter optional) ● Supports DPMS for monitor power management ● Support DDC2B ● On Screen Control : Auto-Tune, Contrast, Brightness, H/V Position, H-Size, Phase, Auto-Level, Color Control, OSD Position, OSD Time-out, Power Save Delay, Language, Information. ● Built-in color active matrix TFT (Thin Film Transistor) Liquid Crystal Display (LCD) that uses amorphous silicon TFTs as a switching device.
INSTALLATION ENG Follow these steps to install the monitor 1. Before you connect the cables, make sure the monitor and system unit power switches are OFF. 2. Plug one end of the 15-pin signal cable to the rear of your system. The adapter may be required for certain Apple Macintosh computers. Tighten the two screws on the cable connector. 3. Connect the power cord to the inlet socket which is located at the AC Adapter. Connect the plug into an AC wall outlet. 4.
CONTROL BUTTONS ENG Front Controls Button Description : 1. MENU/EXIT OSD(ON SCREEN DISPLAY)MENU diagram appears on the screen when MENU/EXIT button is pressed. Pressing of button when OSD MENU appears enables exit from OSD MENU. 2. AUTO/SELECT If the button is pressed during the screen state, automatic adjustment into optimal size and location is executed. If the button is pressed on the state of OSD MENU, operation is executed with selection button. ▲ ,▼ ) 3.
ON-SCREEN DISPLAY ENG This LCD monitor features an On-Screen Display OSD menu. These icons are designed to make adjusting your monitor display settings easier. When highlighted, the icons illustrate the control function to assist you in identifying which control needs adjustment. Before activating the OSD menu, the SELECT/AUTO button can be used to automatically adjust the display to the proper size and horizontal and vertical position. (Press button for 2 seconds.
MENU DESCRIPTIONS ENG 1. BRIGHTNESS / CONTRAST Adjustment This menu is used when the brightness and contrast level of the screen need to be adjusted. Use ▲and ▼button to adjust. 2. COLOR Adjustment After selecting this menu, use ▲and ▼button to adjust R, G and B color on the USER mode according to user preference. 3.
MENU DESCRIPTIONS ENG 4. SETUP---OSD Information Modification (1)OSD POSITION After selecting this menu, use ▲and ▼button to adjust the location of OSD that appears on the screen. (2) OSD TIME After selecting this menu, use ▲and ▼button to adjust the time needed to materialize the OSD screen that appears on the screen. (3) LANGUAGE After selecting this menu, use ▲and ▼button to adjust the language used on the OSD screen that appears on the screen.
OPTION ENG *Caution This page applies to the product that added on the Option(DVI, S-VIDEO) specs. OSD POSITION OSD TIME LANGUAGE SOURCE EXIT ▶ ▶ ▶ ▶ 1 30SEC ENGLISH ANALOG OSD POSITION OSD TIME LANGUAGE SOURCE EXIT ▶ ▶ ▶ ▶ 1 30SEC ENGLISH S-VIDEO DVI SOURCE in the OSD SETUP needs to be adjusted when the DVI, S-VIDEO OPTION is added on. 1. SOURCE: Input Signal ▼ button to adjust into ANALOG, DVI, S-VIDEO as After selecting this menu, use ▲ and▼ desired buy user.
POWER MANAGEMENT ENG LED INDICATOR (POWER MANAGEMENT ACTIVE) The power management feature of this LCD monitor is comprised of two stages : On or Out of Range(Green), Off (Amber/Green blinking). In the off mode, all circuitry in the monitor is shut down, except for a low power detection circuit. This circuit allows the monitor to wake up when the mouse is moved or a key on the keyboard is pressed.
TIMING GUIDE ENG The LCD is a multi-frequency display. It operates at horizontal frequencies between 30KHz~80KHz and vertical frequencies between 56Hz~75Hz. Because of its microprocessor-based design, it offers auto-synchronization and auto-sizing capabilities. This monitor offers 10 preprogrammed settings that are listed in the timing table on page 11. These preset modes cover most of the common video modes supported by popular graphics adapters.
PIN ASSIGNMENT ENG POWER JACK 1 Ground 2 DC + 12V VGA Connector Pin 1 Red Pin 2 Green Pin 3 Blue Pin 4 No Connection Pin 5 Ground Pin 6 Red Ground Pin 7 Green Ground Pin 8 Blue Ground Pin 9 No Connection Pin 10 Ground Pin 11 Ground Pin 12 DDC SDA Pin 13 Horizontal Sync. Pin 14 Vertical Sync. Pin 15 DDC SCL * Note : When resolutions are shown that are lower than the pixel count of the LCD panel, text may appear choppy or bold.
SPECIFICATIONS ENG Type LCD Color Filter Colors Glass surface 17”diagonal viewable screen TFT (Thin Film Transistor) Active Matrix Panel, 0.264mm pixel pitch R,G,B vertical Stripe 16.7M Anti-glare coating Viewing Angles (CR≥10) Contrast Ratio Left / Right Up / Down Typ. 65。/ 65。 45。/ 65。 Luminance of White Typ. 250cd/m2 Compatibility PC IBM XT, AT, 386, 486, Pentium or PS/2 and compatibles (from VGA up to 1280 x1024 @ 75Hz NI.) Refresh Rate Max.
TROUBLESHOOTING ENG No power. Flip the power switch ON. The Power LED turns on. Make sure AC power cord is securely connected to the power jack and to a power outlet. Power on but no screen image. Make sure the video cable attached with this monitor is tightly secured to the video output port on the back of the computer Adjust the brightness and contrast. Image is unstable, unfocused. Use AUTO-TUNE to adjust automatically.
ENG Entire screen image rolls (scrolls) vertically. Make sure the input signals are within the LCD monitor's specified frequency range. (Maximum : VESA, MAC 1280×1024 @ 75Hz) Connect the video cable securely. Try the Monitor with another power source. Control buttons do not work. Press only one button at a time. ABOUT THE LCD The LCD contains over 3,932,160 thin-film transistors (TFTs).