Use Instructions

Communicator
4NR016
Getting started guide
CAUTION – Investigational device.
Limited by Federal (or United States) law
to investigational use.
Manufacturer
Medtronic plc
710 Medtronic Parkway,
Minneapolis, MN 55432-5604,
USA
www.medtronic.com
Tel. [phone]
Fax [phone]
© Medtronic plc 2019
All Rights Reserved
NRP1232-43525 Rev 2.0
2019-02-01
Recharge components for the Medtronic
HAPTIX Implantable Neurostimulator
Controller (INC)
The Model 4NR016 Communicator is intended for use
in conjunction with the MDT 97745 Recharge
Controller, 97755 Recharger, and 97745AC adapter to
recharge the HAPTIX 4NR015 INC.
Communicator components and
accessories in the Model 4NR016
Communicator package:
* Medtronic Model 4NR016 Communicator
* 2 AAA alkaline batteries
Additional recharge components supplied
separately by Medtronic:
* 97745 Recharge Controller
* 97755 Recharger
* 97745AC Power Supply
Instructions for use
Notes:
* For instructions to pair the communicator to the
4NR015 INC and use during recharge, refer to the
Communicator Technical Manual.
* Refer to the Model 4NR016 Communicator
Technical Manual for warnings, cautions,
specifications, instructions for use, maintenance,
and troubleshooting. That manual also contains
the electromagnetic compatibility (EMC)
declaration.
The Bluetooth®, Bluetooth Low Energy®,
BLE® trademarks and logos are registered
trademarks owned by Bluetooth SIG, Inc. and
any use of such marks by Medtronic is under
license.
Storage and operating conditions
___________________________________
Parameter Storage Operating
Minimum –35 °C 10 ºC
Temperature (–31 °F) (50 °F)
Maximum 58 °C 40 ºC
Temperature (136 °F) (104 °F)
___________________________________
Installing batteries in the communicator
1. Release the battery compartment lid by sliding it
downward (Figure 1)
.
Figure 1. Opening the battery compartment.
2. Lift the battery compartment lid (Figure 2).
Battery lid
Batteries
Figure 2. Battery compartment.
3. Insert 2 new AAA alkaline batteries
according to the orientation indicated on the
inside of the battery compartment.
4. Close the battery compartment lid.
5. Secure the battery compartment lid by
sliding it upward.
6. Remove batteries when device is not in use.
Turning the communicator on and off
Figure 3. The power switch
The power switch has a power symbol ( ) on it
and is located on the side of the communicator
(Figure 3).
To turn the communicator on
Slide the power switch as illustrated in Figure 3 and
then release it. Confirm the Battery Icon is illuminated
green. The communicator will start its communication
activity. Further information on communicator activity
during recharge is contained in the Communicator
Technical Manual.
To turn the communicator off
Slide the power switch, hold it for 2 seconds, then
release it. Confirm the Battery Icon is not illuminated
or flashing.
Connecting the 97745AC Power Supply
cable to the communicator
The 97745AC Power Supply can be used to power the
communicator if desired (fresh batteries unavailable,
etc.)
1. Connect the power supply cable to the
communicator:
a. Ins
ert the custom plug of the power supply
cable into the custom port on the communicator
(Figure 4).
Figure 4. Connect the plug of the
power supply cable to the communicator.
2. Plug the 97745AC Power Supply into a US main
60Hz 110-120VAC power source.
3. Power the communicator on and off as directed
above.
Disconnecting the 97745AC Power Supply
cable from the communicator
The 97745AC Power Supply can be disconnected
when external power is no longer required for the
communicator (recharge session complete, desire to
switch to battery power, etc.)
1. Power the communicator off as described
above.
2. Unplug the 97745AC Power Supply from the
communicator.
Note: Store the batteries and 97745AC Power Supply
in the same location as the 4NR016 communicator,
97745 Recharge Controller, and 97755 Recharger.
Custom plug
Document Not For Medical Use