HDDigital DigitalAdapter Adapter Easy EasySetup Setup Guide Installation Installation••Operation Operation••Troubleshooting Troubleshooting Pace DC60Xu
What You Need To Know Table Of Contents To bring you better service now and in the future Mediacom is upgrading to an All Digital network – All Digital for every channel, on every TV set. What’s Included In This Install Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Items You May Also Need . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Start Here. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
What’s Included What’s included in this Install Kit? Kit In This Installation What’s included in this Install Kit? Digital Adapter Digital Adapter Each TV will need to be connected to a Digital Adapter or a Digital Adapter Each TV will need to be connected to a Digital Digital Cable Box, but not both. Each TV will need to be connected to a Digital Adapter or a or a Digital Cable Box, but not both. Digital Cable Box, but not both.
Start Here Please refer to the Welcome Letter that was delivered with this kit to identify: 1 List the last four digits of the serial number of each Digital Adapter you will be activating. Serial Number Location In Your Home Output Channel The account number associated with your Mediacom account. 2 Any specific instructions not included in this Setup Guide.
Connecting To A TV With An HDMI Cable 1 Connect the Digital Adapter to the Cable Outlet A Turn off your TV. B Locate the cable that currently runs from the cable wall outlet to the back of your TV. Leave one end of the cable connected to the wall, but disconnect the other end from the back of your TV. C Reconnect this end of the cable to the “Cable In” input on the back of the Digital Adapter. 8 2 Connect the Digital Adapter to the TV A Find the HDMI cable included in this kit.
Power Up A If you are connecting the Digital Adapter to a television with HDMI, set your TV to choose “HDMI” as the input source. OR Pick which output channel your TV will use (Ch 3 or Ch 4) and set the switch on the back of the Digital Adapter to the proper output channel you selected. CC Plug into aaworking workingelectrical electrical outlet power Plugthe theother other end end into outlet or or power strip.strip.
Connecting To The Cable Network And Activating Your Digital Adapter Remember, you must wait 20 minutes before calling to activate. This will allow the Digital Adapter to connect to the cable network and retrieve the latest updates. Remote Control Setup Instructions The RF remote control you received in your HD Digital Adapter kit must be set up before it will work with your television and Digital Adapter. This is a two-step process.
RF Remote Pairing Process When multiple remotes work in a shared space, interference can result. To avoid this problem, the remote must be paired with the HD Digital Adapter. Step 1 Turn on your TV using the buttons on the TV or the TV remote. Make sure power is connected to your HD Digital Adapter and it is plugged into the TV. Note: Your TV must always be set to the proper channel (Ch 3 or Ch 4) or HDMI input to match the output channel on the back of your HD Digital Adapter.
Step 6 Turn on your TV. On the remote control, press and hold the SETUP button until the indicator LED changes from red to green, then press the “A” button. Step 7 Press the CH^ (channel up) button several times until the TV turns off. After the TV turns off, press the SETUP button. The indicator LED will blink twice in green when the TV code is successfully stored. Step 8 Point the new remote control at the TV. Press the POWER button on the remote to turn on your TV.
Verify Your Mediacom Services Digital Adapter Operation Guide After completing the activation step, wait a few minutes for programming to appear. Quick Troubleshooting Checklist A 1 C Confirm TV is on the proper HDMI input or proper output channel (Ch 3 or Ch 4). 2 Digital Adapter light is on. B A Be sure the TV is on the proper HDMI input or channel (Ch 3 or Ch 4). Confirm that the Digital Adapter is connected to power and that the light on the front is solid (not blinking).
Remote Operation Guide TV Power When the remote has been programmed to the TV, TV POWER will turn the TV on and off. All Power Use POWER to turn the Digital Adapter on and off. Note: The DTA Power Off feature may not be enabled. Mute Press MUTE once to turn the sound on or off. Last Use LAST to recall the last channel. Key Pad Use the key pad (0-9) to directly select the channels. Guide Use GUIDE to display the Electronic Program Guide.
Troubleshooting Guide If your Digital Adapter is not coming on: •• Make sure that the power cord is securely connected to the back of the Digital Adapter. •• Make sure that the Digital Adapter power cord is plugged into a working power outlet. If there is no picture on the TV and the light on the Digital Adapter is blinking: •• Check your cables and make sure that they are attached correctly. •• Unplug the Digital Adapter, plug it back in, then wait five minutes for it to reset.
M731-22873 HD DTA Guide - Pace