CATALOG Product Image Parts Listing Installation Notes Tools Required Installation Steps Safety Tips Troubleshooting Guide iB iB Customer Service
PARTS LISTING DDS Name Name | Picture Sliding Glass Middle: Seal Anti Splash Guile Rail Shallot Roller Serial Plug Anith-juiriging er STE vit Resew Texas @ @® ee Wall Bracket Sere STs Soft Close Cornwall Plug Blanch Guide Blog Template lee Towel Bar Allen Key @ Sidle Heat it LL FRAGILE WITH PARE LIFT Please keep this manual and product code number for future reference and for-ordering replacement parts if necessary, a.
PARTS LISTING Aluminum punch template Wall Bracket {If missing or broken, please: refer to page 8 for punch data) Anti Jumping Knob Roller Towel Bar Guide Block Allen key
NOTES BEFORE INSTALLATION Prepare the tools. (Please refer to page 6) All measurements and installation should do after the wall and shower base were completed. i. Make sure shower base is horizontal and both wall are vertical, if shower base not horizontal or the wall not vertical, please contact our installation support. E5 Understand the names and uses of individual accessories of shower doors. (Please refer to page 2~4) Installation by licensed professional contractor is recommended.
TOOLS REQUIRED {Please bring your own tools) (we offer) Aluminum punch template Spirit level Tape measure Power drill Drill Bits 5/16" & 14" Rubber hammerer Hacksaw eR IEEE— hae Silicone Gun Modified Ypsilanti) Polymer
INSTALLATION STEPS Measuring Glass guide block Soft close Punching Handle Wall bracket Door seal Guide rail Bottom anti-splash threshold Roller Gluing *Customer Service 470-926-8618 321-946-6293
(Ty According to the assigned aluminum punching template (please measure with horizontal ruler), draw the punching point position after ensuring the slope value, Product Height |X Y 80" 557/87" | 78" 66” 61-78" | TR” 72" §7-78" | 718" 7e" 7-gr | 7g 79" 74-718" | 1/18" “Same punching data for betrothals (2) brill the holes according to the drawn holes, making sure that there is'no offset-of the: holes.
i Bh the guide vial need robe cut to match your shower opening please dot based on actual measurements. If stretch the product installation width please adjusting the insertion depth of the wall bracket to the guide rail without.cutting the guide rail. DST has maximum installation width stretch of 3/4" for catechize. @ After the installation of the guide rail, please use the level ruler fo measure whether the level.
(5) After installing the rollers, hang the door on ‘the guide rail (8 Installation of sliding glass: The height and level of the glass tan'be adjusted slightly by adjusting the rollers; through this adjustment can be adapted to the shower with little wall offset, each wall offset preferably not mare than 1/4" = 10
(after the glass installation is completed, please measure the glass with:level ruler to confirm the vertical horizontal of the glass and then install the glass guide block.
@Soft-close fixed position: please adj list the soft-close to the right position after the door is dosed(need to.allow for the width of door seal, you can install door seal before test), Because the soft-close positiveness determine the:closing position, determine the soft-close position after the door is closed, then tighten the four soft-closes” screw-on a total of § strews.
8) The door seal can be installed according to your preference, but vou need to ensure that there is minimum a wide door seal in the middle when. you shower, The top of wide door seal needs to bie slightly lower than the bottom of anti-jump knobs to avoid scraping.
9 Install the anti-splash threshold according to the guidelines, please cut to the tight size according to the width of your shower opening: Cleanup the garbage and dry the water and stains with a soft cloth after installation then applicability glass glue. Note: Please dry for 24 hours offer the gloss glue is applied before use.
SAFETY TIPS: : Do not remove the glass protection corners during installation, remove them only after installation is complete. Wear protective equipment when drilling, cutting guide rail and anti-splash threshold. ma Careful installation of the glass is required during installation, please do not step on the glass to avoid bumping #5 Wait 24 hours after installation before using the shower. SHOWER DOOR MAINTENANCE AND CARE: Shower door glass is double-sided easy-clean glass.
TROUBLESHOOTING GUIDE AND NOTE Wall bracket punching issues: (11: | got the vertical punching data, but I'm not sure horizontal data, please advise. Al: DDS is symmetrical inside and outside, when your threshold width is 3 1/4" or wider, the vertical surface of wall bracket drilling position can be in the middle of threshold.
TROUBLESHOOTING GUIDE AND NOTE Soft-close installation Issues: 1: The anti-jump knob can not drive the soft-close inner hook to open position when open the road, and resulting in the soft-close inner hook back to close the door position. How to solve knob is too low) #1: The height of anti-jump knob is too low; anti-jump knob distance from the bottom to the soft-close groove should be 0.04" (tummy.
Please contact our customer service to confirm the return steps before returning or get order replacement. Customer Service: 470-926-8618 321-946-6293 Installation Video: www.mcocodsupport.com Return Address: +4800 Little John St.