PP CATALOG Product Image Parts Listing Installation Notes Tools Required Installation Steps Safety Tips Troubleshooting Guide Customer Service
PARTS LISTING DODSON z O Name Name | Picture z © ® Sliding Glass Middle: Seal Anti Splash Guile Rail Shallot Roller Serial Plug Ant-japanning er STE vit Resew Texas @ @® ee Wall Bracket Sere STs Ant Collision Gen Wall Plug Hick ) Blanch Guide Blog Template lee Towel Bar Allen Key @ Sidle Heat it Ems FRAGILE WITH CARE LITE Please keep this manual and product code number for future reference and for-ordering replacement parts if necessary, a.
PARTS LISTING Aluminum punch template Wall Bracket ({missing or broken, please refer 16 page 8.
NOTES BEFORE INSTALLATION Prepare the tools. (Please refer to page 6) All measurements and installation should do after the wall and shower base were completed. 1 Make sure shower base is horizontal and both wall are vertical, if shower base not horizontal or the wall not vertical, please contact our installation support. gr Understand the names and uses of individual accessories of shower doors. (Please refer to page 2~4) Installation by licensed professional contractor is recommended.
TOOLS REQUIRED {Please bring your own tools) (we offer) Aluminum punch template Spirit level Tape measure Power drill Drill Bits 5/16" & 14" Rubber hammerer Hacksaw eR IEEE— hae Silicone Gun Modified Ypsilanti) Polymer
INSTALLATION STEPS Measuring Glass guide block Punching Handle Wall bracket Door seal Guide rail Bottom anti-splash threshold Roller Gluing *Customer Service 470-926-8618 321-946-6293
A} According to the assigned aluminum punching template {please measure with horizontal ruler), draw:the punching point position after ensuring the slope value, wel x |v 80" 1559/16" 7/8" 66” 161-9116" 7/8" 72° 167-9116" 7/8 76" [71-9716] 7/8" 79" T4918" TRB" *Rae punching data for basketballs @) Drill the holes according to the:drawn holes, making sure that there Is nu offset of the holes, The drilling positions of the left and right walls need to ban alignment and on the same horizontal and vertical plane
Gif the guide rail need robe cut to match your shower opening please dot based on actual measurements. If stretch the product installation width please adjusting the insertion depth of the:wall bracket to:the guide rail without-cutting the guide rail. DDS has maximum installation width stretch of 1" for each size. @ After the installation of the guide rail, please use the level tiler to measure whether the level. S90.
Sliding door Sliding do Er after installing the rollers, Katy the dor on the guide rai 8 installation of sliding glass: The height and level of the:glass cane adjusted slightly by adjusting the rollers; through this adjustment can be adapted to the shower with & little offsetting, each wall.
(Dater the glass installation is completed, please measure the glass with level ruler to confirm the vertical and horizontal of the:glass and then install the glass guide block: il
quay Sliding dour i Blinding doo: (B Please follow the guide to install the handle and anti-jumping knobs. Anti-jumping kinase dio. not incompletely case to the guide rail, need leave gaslight to avoid sliding smooths, 8) The door seal can bé installed according to your preference, but vou need to ensure that there'is minimum a wide door seal in the middle when you:shower, The top of wide door seal needs to be slightly lower than the bottom of anti jump knobs to avid scraping.
40) install the anti-splash threshold according to the guidelines, please cut ta the right sire according to the width of your shower opening. Cleanup the garbage and dry the water and stains with a soft cloth after installation then appliqueing glass glue. Note: Please dry for 24 hours feather glass glue is applied before use. 13.
SAFETY TIPS: : Do not remove the glass protection corners during installation, remove them only after installation is complete. Wear protective equipment when drilling, cutting guide rail and anti-splash threshold. ma Careful installation of the glass is required during installation, please do not step on the glass to avoid bumping #5 Wait 24 hours after installation before using the shower. SHOWER DOOR MAINTENANCE AND CARE: Shower door glass is double-sided easy-clean glass.
TROUBLESHOOTING GUIDE AND NOTE Shower doors don't close tightly issues: 31 When | close the door, the door closes then backs out and never closes tight. How should | do? Al: First please check that the anti collision block is installed on both sides, it will hold the glass in place when closing the door to keep it closed. Then use a level to check your guide rail and glass level status, if not installed level, you can adjust the top roller to adjust the sliding glass level and height.
Please contact our customer service to confirm the return steps before returning or get order replacement. Customer Service: 470-926-8618 321-946-6293 Installation Video: www.mcocodsupport.com Return Address: +4800 Little John St.