Table of Contents Introduction Instrument Cluster 4 12 Warning and control lights Gauges 12 16 Entertainment Systems 19 AM/FM AM/FM AM/FM AM/FM stereo stereo with CD stereo with in-dash six CD stereo with CD/MP3 Climate Controls Manual heating and air conditioning Lights Headlamps Turn signal control Bulb replacement Driver Controls Windshield wiper/washer control Power windows Speed control (Cruise control) 19 21 23 27 35 35 38 38 40 40 47 47 49 53 Locks and Security 59 Keys Locks Anti-the
Table of Contents Seating and Safety Restraints Seating Safety restraints Air bags Child restraints Driving 67 69 82 93 110 Starting Brakes Transmission operation Vehicle loading Trailer towing Recreational towing 110 115 119 129 131 138 Roadside Emergencies 140 Hazard flasher switch Fuel pump shut-off switch Fuses and relays Overheating Changing tires Jump starting Wrecker towing 140 140 141 151 152 158 164 Customer Assistance Reporting safety defects (U.S.
Table of Contents Maintenance and Specifications Engine compartment Engine oil Battery Fuel information Refill capacities Lubricant specifications Engine data 182 192 196 202 208 232 235 236 Accessories 239 Index 240 All rights reserved. Reproduction by any means, electronic or mechanical including photocopying, recording or by any information storage and retrieval system or translation in whole or part is not permitted without written authorization from Mazda Motor Corporation.
Introduction CALIFORNIA Proposition 65 Warning WARNING: Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. In addition, certain fluids contained in vehicles and certain products of component wear contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
Introduction SAFETY AND ENVIRONMENT PROTECTION Warning symbols in this guide How can you reduce the risk of personal injury and prevent possible damage to others, your vehicle and its equipment? In this guide, answers to such questions are contained in comments highlighted by a bold WARNING statement. These comments should be read and observed.
Introduction SPECIAL NOTICES Emission warranty The New Vehicle Limited Warranty includes Bumper to Bumper Coverage, Safety Restraint Coverage and Corrosion Coverage. In addition, your vehicle is eligible for Emissions Defect and Emissions Performance Warranties. For a detailed description of what is covered and what is not covered, refer to the Warranty Guide that is provided to you along with your Owner’s Guide.
Introduction Special instructions For your added safety, your vehicle is fitted with sophisticated electronic controls. WARNING: Please read the section Air bag in the Seating and safety restraints chapter. Failure to follow the specific warnings and instructions could result in personal injury. WARNING: Front seat mounted rear facing child or infant seats should NEVER be used in front of a passenger side air bag unless the air bag can be and is turned OFF.
Introduction These are some of the symbols you may see on your vehicle.
Introduction Vehicle Symbol Glossary Power Windows Power Window Lockout Personal Alarm System Feature Engine Oil Engine Coolant Engine Coolant Temperature Do Not Open When Hot Battery Avoid Smoking, Flames, or Sparks Battery Acid Explosive Gas Fan Warning Power Steering Fluid Maintain Correct Fluid Level Emission System Engine Air Filter Passenger Compartment Air Filter Jack MAX MIN Check fuel cap INFORMATION ABOUT THIS GUIDE The information found in this guide was accurate at the time of
Instrument Cluster Instrument panel dimmer/dome light control (pg. 39) Instrument cluster (pg. 12) Headlamp control (pg. 38) DOOR AJAR CHECK GAGE 4 3 H CHECK ENGINE 5 6 30 20 1 CHECK FUEL CAP F ABS 10 0 ! E 60 70 80 0 0 0 80 100 P 40 90 120 60 2 C 50 40 RPMx1000 140 000000 20 MPH R N D 2 1 160 100 180 110 km/h 120 H SPEED CONT L 4WD HIGH H 4WD LOW L THEFT BRAKE O/D OFF OFF DIM ON SET ACC OFF Turn signal and wiper/washer control (pg.
Instrument Cluster 4wd control* (pg. 125) Audio system (pg. 19) Auxiliary power point (pg. 49) Fog lamp control (pg. 38) Cigar lighter Passenger air bag deactivate switch (pg. 88) Climate control system (pg.
Instrument Cluster WARNING LIGHTS AND CHIMES Warning lights and gauges can alert you to a vehicle condition that may become serious enough to cause expensive repairs. A warning light may illuminate when a problem exists with one of your vehicle’s functions. Many lights will illuminate when you start your vehicle to make sure the bulb works. If any light remains on after starting the vehicle, have the respective system inspected immediately.
Instrument Cluster If the light remains on, have your vehicle serviced at the first available opportunity. CHECK NOTE: The ENGINE light will illuminate if vehicle refueling is conducted with the engine running. WARNING: Never refuel vehicle with the engine running. Light is blinking: Engine misfire is occurring which could damage your catalytic converter. You should drive in a moderate fashion (avoid heavy acceleration and deceleration) and have your vehicle serviced at the first available opportunity.
Instrument Cluster WARNING: Driving a vehicle with the brake system warning light on is dangerous. A significant decrease in braking performance may occur. It will take you longer to stop the vehicle. Have the vehicle checked by your dealer immediately. Anti-lock brake system: If the ABS light stays illuminated or ABS continues to flash, a malfunction has been detected, have the system serviced immediately. Normal braking is still functional unless the brake warning light also is illuminated.
Instrument Cluster Door ajar: Illuminates when the ignition is in the ON position and any door is open. Overdrive off (if equipped): Illuminates when the overdrive function has been turned OFF using the transmission control switch (TCS). DOOR AJAR O/D OFF If the light does not come on or the light flashes steadily, have your vehicle serviced as soon as possible, damage to the transmission could occur. Four wheel drive low (if 4WD equipped): Illuminates when LOW four-wheel drive low is engaged.
Instrument Cluster Key-in-ignition warning chime: Sounds when the key is left in the ignition in the OFF/LOCK or ACC position and the driver’s door is opened. Headlamps on warning chime: Sounds when the headlamps or parking lamps are on, the ignition is off (and the key is not in the ignition) and the driver’s door is opened. GAUGES Speedometer: Indicates the current vehicle speed. Engine coolant temperature gauge: Indicates engine coolant temperature.
Instrument Cluster WARNING: Never remove the coolant reservoir cap and/or the radiator cap while the engine is running or hot, this may result in serious burns. Odometer: Registers the total kilometers (miles) of the vehicle. Trip odometer: Registers the kilometers (miles) of individual journeys. To reset, depress the control button.
Instrument Cluster Engine oil pressure gauge: Indicates engine oil pressure. At normal operating temperature, the needle will be in the normal range H (the area between the “L” and “H”); if the needle goes below the L normal range, stop the vehicle as soon as safely possible and switch off the engine immediately. Check the oil level. Add oil if needed (refer to Engine oil in the Maintenance and Specifications chapter).
Entertainment Systems AM/FM STEREO 6 5 7 1 2 VOL PUSH ON TONE TONE VOL ST SEEK DX FM 12 TUNE CLK 1 2 3 4 AM/FM 3 4 / to find the 1. Seek: Press next strong station down/up the frequency band. / to 2. Tune: Press manually change radio frequency down/up. 3. AM/FM: Press to choose a frequency band in radio mode. AM/FM 4. Memory preset buttons: To 1 2 set a station: Select frequency band AM/FM; tune to a station, press and hold a preset button until sound returns.
Entertainment Systems 5. Power/volume: Press to turn ON/OFF; turn to increase or decrease volume levels. 6. Tone: Press TONE until the desired level — Bass, Treble, TONE Fade appears on the display. CLK Turn the volume control to raise/lower the levels, or to move the audio sound from the right to left or the front to back (if equipped). 7. CLK (Clock): To set the hour, press and hold CLK until CLOCK SET appears in the display. Press SEEK to or increase decrease the hours.
Entertainment Systems AM/FM STEREO / SINGLE CD RADIO 14 15 16 17 18 13 1 2 3 4 6 5 VOL - PUSH ON AM FM SCN ST FM1 BASS TREB BAL FADE CD CLK 12 DISC SEEK EJ TUNE COMP DISCS 11 CD 1 10 CD 2 SHUFFLE 3 9 4 5 6 8 7 / to shift 1. Balance: Press sound to the left/right speakers. / to shift 2. Fade: Press sound to the front/rear speakers. 3. SCN (Scan): Press to hear a brief sampling of all listenable stations or CD tracks. Press again to stop. 4.
Entertainment Systems 5. EJ (eject): Press to eject a CD. 6. COMP (Compression): In CD mode, press to bring louder and softer levels into more comfortable listening level. The compression icon (c) will appear in the display. SHUFFLE 7. Shuffle: Press to listen to the 6 tracks on the CD in random order. Press again to turn off. 8. Memory presets: To set a CD CD SHUFFLE 1 2 3 4 5 6 station: Select frequency band AM/FM; tune to a station. Press and hold a preset button until sound returns.
Entertainment Systems 14. CD: Press to enter CD mode or to play a CD already loaded into the system. 15. AM/FM: Press to choose a frequency band in radio mode. 16. Bass: Press / to increase/decrease the bass output. / to 17. Treble: Press increase/decrease the treble output. 18. CD door: Insert a CD printed side up.
Entertainment Systems 1. Seek: Press and release SEEK / for previous/next strong station, or track of current disc. 2. Rewind: Press for a slow rewind, press and hold for a fast rewind. Fast forward: Press for a slow advance, press and hold for a fast advance. 3. Comp (Compression): In CD mode, press to adjust the soft and loud passages together for a more consistent listening level. Press the COMP control until COMP ON is displayed. 4. Mute: Press to MUTE playing media; press again return to playing media.
Entertainment Systems Fade: Press FADE; then press SEL / to shift sound to the rear/front speakers. 9. Menu: Press MENU and SEL to access clock mode, RDS on/off, Traffic, Program type, Show type and Compression modes. Traffic: Allows you to hear traffic broadcasts. With the feature ON, press SEEK or SCAN to find a station broadcasting a traffic report (if it is broadcasting RDS data). Traffic information is not available in most U.S. markets.
Entertainment Systems AUTOSTORE will flash on the display. When the six strongest stations are filled, the station stored in preset 1 will begin playing. If there are less than six strong stations, the system will store the last one in the remaining presets. Press again to disengage. 13. Power/volume: Press to turn ON/OFF; turn to increase or decrease volume levels. 14. Load: Press to load a CD. Press and hold to load up to six discs. 15. Shuffle: Press to play tracks in random order.
Entertainment Systems MACHT MP3 AUDIO SYSTEM / to shift 1. Balance: Press sound to the left/right speakers. 2. Fade: Press / to shift sound to the rear/front speakers. 3. Scan: Press to hear a brief sampling of all listenable radio stations, CD or MP3 tracks. Press again to stop. 4. CLK: To set the clock press and hold the CLK control for the following functions: • To set the hour, press SEEK to the hours. / • To set the minutes, press TUNE DIR the minutes.
Entertainment Systems 5. EJ (Eject): Press to stop and eject a disc. If a disc is ejected and not removed, the player will automatically reload the disc and return to radio mode. 6. COMP (Compression): In CD and MP3 mode, press to adjust the soft and loud sounds together for a more consistent listening level. The compression icon (c) will illuminate in the display. 7. Shuffle: Press to engage random play on the CD or MP3 disc. SHF then ON will briefly appear in the display.
Entertainment Systems 13. Memory presets: To set a station: Select frequency band AM/FM; tune to a station, press and hold a preset button until sound returns. 14. CD door: Insert a CD with the label side up. 15. Tune/Directory: Press TUNE / to change the DIR radio frequency down/up or change the MP3 directories. 16. Seek: Press and release SEEK / for previous/next strong station selection or CD and MP3 tracks. 17. Power/volume: Press to turn ON/OFF; turn to increase or decrease volume levels. 18.
Entertainment Systems 21. Treble: Press / to decrease/increase the treble output. MP3 FUNCTIONS Your audio system is equipped with MP3 capability which allows you to listen to songs in MP3 flat file mode and MP3 directory mode. To engage MP3 flat file mode, insert an MP3 disc. If an MP3 disc is already present in the player, press the CD control. The MP3 icon will display while the player is in MP3 mode. While in MP3 flat file mode, press the MP3 DIR control to enter into MP3 directory mode.
Entertainment Systems ERROR MESSAGES You may experience an error message for the following situations: • NO DISC when the CD control is pressed and there is not a CD present. • DISC ERR when there is a damaged or unreadable disc. Such as, data discs containing no .mp3 files, or for data discs containing more than 255 files or directories. • CD ERR for any other disc malfunction.
Entertainment Systems This hierarchy is an example of a more complex directory structure. While you are capable of setting up many directory levels when burning a CD, the MACHt MP3 music system will display the structure as if it were only one level deep. Therefore, the system will condense the complex hierarchy into a structure similar to the one-level-deep example above. This will not harm the MP3 disc and will not change the hierarchy that is actually written on the disc.
Entertainment Systems RADIO FREQUENCIES AM and FM frequencies are established by the Federal Communications Commission (FCC) and the Canadian Radio and Telecommunications Commission (CRTC). Those frequencies are: AM - 530, 540–1600, 1610 kHz FM- 87.7, 87.9–107.7, 107.9 MHz RADIO RECEPTION FACTORS There are three factors that can effect radio reception: • Distance/strength: The further you travel from an FM station, the weaker the signal and the weaker the reception.
Entertainment Systems Don’t: • Expose discs to direct sunlight or heat sources for extended periods of time. • Insert more than one disc into each slot of the CD changer magazine. • Clean using a circular motion. CD units are designed to play commercially pressed 12 cm (4.75 in) audio compact discs only. Due to technical incompatibility, certain recordable and re-recordable compact discs may not function correctly when used in CD players.
Climate Controls HEATER ONLY SYSTEM (IF EQUIPPED) 1. Fan speed adjustment: Controls the volume of air circulated in the vehicle. 2. Temperature selection: Controls the temperature of the airflow in the vehicle. 3. Air flow selections: Controls the direction of the airflow in the vehicle. See the following for a brief description on each control. : Distributes outside air through the instrument panel vents. OFF: Outside air is shut out and the fan will not operate.
Climate Controls 4. Direct the outer instrument panel vents towards the side windows To increase airflow to the outer instrument panel vents, close the vents located in the middle of the instrument panel. WARNING: Do not place objects on top of the instrument panel as these objects may become projectiles in a collision or sudden stop. MANUAL HEATING AND AIR CONDITIONING SYSTEM 1. Fan speed adjustment: Controls the volume of air circulated in the vehicle. 2.
Climate Controls • Under normal weather conditions, do not leave the air flow selector in MAX A/C or OFF when the vehicle is parked. This allows the vehicle to “breathe” using the outside air inlet vents. • Do not put objects under the front seats that will interfere with the airflow to the back seats. • Remove any snow, ice or leaves from the air intake area at the base of the windshield. To aid in side window defogging/demisting in cold weather: 1. Select 2. Select A/C 3.
Lights HEADLAMP CONTROL Turns the lamps off. Turns on the parking lamps, instrument panel lamps, license plate lamps and tail lamps. OFF Turns the headlamps on. FOG LAMP CONTROL (IF EQUIPPED) The fog lamps can only be turned on when the headlamp control is in the low beams position. Press the foglamp control to activate the fog lamps. The fog lamp indicator light will illuminate. When the highbeams are activated, the fog lamps will not operate.
Lights High beams After turning the headlamps on, push the lever toward the instrument panel to activate. Pull the lever towards you to deactivate. Flash to pass Pull toward you slightly to activate and release to deactivate. PANEL DIMMER CONTROL Use to adjust the brightness of the instrument panel and all applicable switches in the vehicle during headlamp and parklamp operation. Move the control up or down to adjust the intensity of the panel lighting.
Lights TURN SIGNAL CONTROL • Push down to activate the left turn signal. • Push up to activate the right turn signal. COURTESY/READING LAMPS (IF EQUIPPED) The courtesy lamp lights when: • any door is opened. • the instrument panel dimmer switch is held up until the courtesy lamps come on. • the remote entry controls are pressed and the ignition is OFF. The reading lamps can be turned on by moving the switch on the dome lamp to either the left or the right.
Lights Function Number of bulbs Trade number Park/turn lamps 2 3157 AK (amber) (front) Headlamps 2 9003 Rear stop/tail lamps 2 3157K Rear turn lamps 2 3156K Rear license plate 2 3156K/168 lamps Backup lamp 2 3156K Rear/turn/sidemarker 2 916NA (amber) Fog lamp (if 2 899 equipped) Cargo lamp 1 211-2 Interior overhead lamp 1 912 (906) Front door courtesy 1 168 lamp Map lamps 2 168 (T10) Ashtray lamp 1 161 All replacement bulbs are clear in color except where noted.
Lights WARNING: Handling Halogen Bulbs: When a halogen bulb breaks, it is dangerous. These bulbs contain pressurized gas. If one is broken, it will explode and serious injuries could be caused by the flying glass. If the glass portion of the bulb is touched with bare hands, body oil could cause the bulb to overheat and explode when lit. Never touch the glass portion of the bulb with your bare hands and always wear eye protection when handling or working around halogen bulbs.
Lights To install the new bulb: Handle a halogen headlamp bulb carefully and keep out of children’s reach. Grasp the bulb only by its plastic base and do not touch the glass. The oil from your hands could cause the bulb to break the next time the headlamps are operated. Always wear safety glasses while handling bulbs. NOTE: If the bulb is accidentally touched, it should be cleaned with rubbing alcohol before being used. 1.
Lights 3. Remove screw(s) from lamp assembly. 4. Disengage lamp assembly (it has a snap fit). 5. Rotate bulb socket counterclockwise and remove from lamp assembly. 6. Carefully pull bulb straight out of socket and push in the new bulb. 7. Install the bulb socket in lamp assembly by turning clockwise. 8. Align the lamp on the vehicle and push to snap in place. 9. Install screw(s) on lamp assembly. 10. Install the headlamp on vehicle, push rearward and secure with two retainer pins.
Lights Replacing tail lamp/backup lamp bulbs The tail lamp/backup lamp bulbs are located in the same portion of the tail lamp assembly, one just below the other. Follow the same steps to replace either bulb: 1. Open the tailgate to expose the lamp assemblies. 2. Remove the four screws and the lamp assembly from vehicle. 3. Rotate bulb socket counterclockwise turn and remove from lamp assembly. 4. Carefully pull the bulb straight out of the socket and push in the new bulb. 5.
Lights Replacing high-mount brake lamp and cargo lamp bulbs The replacement of the high-mount brake lamp bulb and cargo lamp bulb is basically the same. This procedure covers the high-mount brake lamp bulb. To remove the brake lamp assembly: 1. Remove the two screws and lamp assembly from vehicle. 2. Remove the bulb socket from lamp assembly by rotating it counterclockwise. 3. Carefully pull bulb straight out of socket and push in the new bulb. To install the brake lamp assembly: 1.
Driver Controls MULTI-FUNCTION LEVER Windshield wiper: Rotate the end of the control away from you to increase the speed of the wipers; rotate towards you to decrease the speed of the wipers. Windshield washer: Push the end of the stalk: • briefly: causes a single swipe of the wipers without washer fluid. • a quick push and hold: the wipers will swipe three times with washer fluid. • a long push and hold: the wipers and washer fluid will be activated for up to ten seconds.
Driver Controls Changing the wiper blades 1. Pull the wiper arm away from the vehicle. Turn the blade at an angle from the wiper arm. Push the lock pin manually to release the blade and pull the wiper blade down toward the windshield to remove it from the arm. 2. Attach the new wiper to the wiper arm and press it into place until a click is heard. 3. Replace wiper blades every 6 months for optimum performance. TILT STEERING WHEEL (IF EQUIPPED) To adjust the steering wheel: 1.
Driver Controls AUXILIARY POWER POINT Power outlets are designed for accessory plugs only. Do not hang any type of accessory or accessory bracket from the plug. Improper use of the power outlet can cause damage not covered by your warranty. The auxiliary power point is located on the instrument panel. Do not plug optional electrical accessories into the cigarette lighter. Use the power point. Do not use the power point for operating the cigarette lighter element.
Driver Controls AUTOMATIC DIMMING REAR VIEW MIRRORS (IF EQUIPPED) The electronic day/night mirror will change from the normal state to the non-glare state when bright lights (glare) reach the inside rear view mirror. When the inside rear view mirror detects bright light from behind the vehicle, the inside rear view mirror will automatically adjust (darken) to minimize glare. Do not block the sensor on the backside of the inside rear view mirror since this may impair proper system performance.
Driver Controls Outside air temperature Display operation of the mirror with the compass feature: • Press the right button to toggle the display between the compass direction and no display. Display operation of mirror with temperature and compass feature: • Press the right button once to display temperature °F and compass. • Press the right button twice to display temperature °C and compass. • Press the right button three times to turn the display OFF.
Driver Controls 3. To change the zone setting, push and hold the right button until ZONE appears in the display. 4. Press the right button repeatedly until desired compass zone number is displayed. The display will change back to the compass direction after 3 seconds when the button is not activated. Compass calibration adjustment The compass calibrates itself under normal driving conditions. There is not a need for manual compass calibration. If calibration is still desired, follow these instructions: 1.
Driver Controls POWER MIRROR CONTROL (IF EQUIPPED) To adjust your mirrors: 1. Select to adjust the left to adjust the right mirror or mirror. 2. Move the control in the direction you wish to tilt the mirror. 3. Return to the center position to lock mirrors in place. SPEED CONTROL (IF EQUIPPED) With speed control set, you can maintain a speed of 48 km/h (30 mph) or more without keeping your foot on the accelerator pedal. Speed control does not work at speeds below 48 km/h (30 mph).
Driver Controls Setting speed control The controls for using your speed control are located on the steering wheel for your convenience. 1. Press the ON control and release it. 2. Accelerate to the desired speed. 3. Press the SET ACC control and release it. 4. Take your foot off the accelerator pedal. on the 5. The indicator light SPEED CONT instrument cluster will turn on. Note: • Vehicle speed may vary momentarily when driving up and down a steep hill.
Driver Controls Increasing speed while using speed control There are two ways to set a higher speed: • Press and hold the SET ACC control until you get to the desired speed, then release the control. You can also use the SET ACC control to operate the Tap-Up function. Press and release this control to increase the vehicle set speed in small amounts by 1.6 km/h (1 mph). • Use the accelerator pedal to get to the desired speed. When the vehicle reaches that speed, press and release the SET ACC control.
Driver Controls • Press the speed control OFF control. Note: When you turn off the speed control or the ignition, your speed control set speed memory is erased. OVERDRIVE CONTROL (IF EQUIPPED) Activating overdrive (Overdrive) is the normal drive position for the best fuel economy. The overdrive function allows automatic upshifts and downshifts through all available gears. Deactivating overdrive Press the Transmission Control Switch (TCS) located on the end of O/D ON/OFF the gearshift lever.
Driver Controls CENTER CONSOLE (IF EQUIPPED) Your vehicle may be equipped with a variety of console features. These include: • Utility compartment with cassette/compact disc storage • Cupholders • Coin holder slots • Flip up armrest WARNING: Use only soft cups in the cupholder. Hard objects can injure you in a collision. BED EXTENDER (IF EQUIPPED) Your vehicle may be equipped with a bed extender designed to extend the pickup box for longer loads. To extend the bed extender: 1. Lower tailgate. 2.
Driver Controls Note: If the red marking on the shaft is visible, the bed extender is not locked or properly secured. To stow the bed extender, follow steps one through four in reverse order. The bed extender may be used to secure a load of up to 46 kg (100 lbs.) on the tailgate. The bed extender should always be kept in the stowed position with the tailgate closed when not in use. To remove the bed extender: 1. Extend the bed extender. 2. Pull the round knobs on each side of the extender to unlock it.
Locks and Security KEYS The key operates all locks on your vehicle. In case of loss, replacement keys are available from your dealer. You should always carry a second key with you in a safe place in case you require it in an emergency. Refer to SecuriLocky Passive Anti-Theft System for more information. POWER DOOR LOCKS (IF EQUIPPED) Press the top of the control to unlock all doors and the bottom to lock all doors.
Locks and Security Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Your vehicle is equipped with a remote entry system which allows you to: • unlock the vehicle doors without a key. • lock all the vehicle doors without a key. • activate the personal alarm.
Locks and Security Power door unlock disabled The UNLOCK feature on your power door locks will not work from inside the vehicle when: UNLOCK LOCK • the ignition has been turned to the OFF position, and • 20 seconds elapse after all vehicle doors are closed and locked using the remote entry transmitter, or the power door unlock control (while the accompanying door is open).
Locks and Security To replace the battery: 1. Twist a thin coin between the two halves of the remote entry transmitter near the key ring. DO NOT TAKE THE FRONT PART OF THE REMOTE ENTRY TRANSMITTER APART. Damage to the transmitter may result in operation failure. 2. Remove the old battery. 3. Insert the new battery. Refer to the diagram inside the remote entry transmitter for the correct orientation of the battery. 4. Snap the two halves back together.
Locks and Security 3. Turn the key from the 2 (LOCK) position to 3 (OFF). 4 3 5 2 1 4. Cycle, eight times, rapidly (within 10 seconds) between the 3 (OFF) position and 4 (ON). Note: The eighth turn must end in the 4 (ON) position. The instrument lights in the cluster will come on for a bulb check in the 4 (ON) position. 5. The doors will lock, then unlock, to confirm that the programming mode has been activated. 6. Within 20 seconds press any button on the remote entry transmitter.
Locks and Security • they have been turned on with the dimmer control, or • any door is open. The battery saver will shut off the interior lamps 45 minutes after the last door is closed, even if the dimmer control is on. SECURILOCKY PASSIVE ANTI-THEFT SYSTEM SecuriLocky passive anti-theft system is an engine immobilization system. This system is designed to prevent the engine from being started unless a coded key programmed to your vehicle is used.
Locks and Security Automatic arming The vehicle is armed immediately after switching the ignition to the 3 (OFF) position. The THEFT indicator will flash every two seconds when the vehicle is armed. 4 3 5 2 1 Automatic disarming Switching the ignition to the 4 (ON) position with a coded key disarms the vehicle. • The THEFT indicator will illuminate for three seconds and then go out.
Locks and Security • If you do not have at least 2 previously programmed keys, you must take your vehicle to your dealer to have the spare key(s) programmed. 1. Insert a previously programmed coded key into the ignition. 4 2. Turn the ignition from the 3 3 (OFF) position to the 4 (ON) 5 position. Keep the ignition in the 4 (ON) position for at least 2 one second, but no more than 10 seconds. 1 3. Turn the ignition to the 3 (OFF) position, and remove the coded key from the ignition. 4.
Seating and Safety Restraints SEATING Adjusting the front manual seat WARNING: Never adjust the driver’s seat or seatback when the vehicle is moving. Sudden braking or a collision could cause serious injury. Adjust the seat only when the vehicle is stopped. WARNING: Do not pile cargo higher than the seatbacks to reduce the risk of injuring people in a collision or sudden stop. WARNING: Always drive and ride with your seatback upright and the lap belt snug and low across the hips.
Seating and Safety Restraints Pull lever up to adjust seatback. Using the manual lumbar support (if equipped) Turn the lumbar support control clockwise to increase firmness. Turn the lumbar support control counterclockwise to increase softness. Passenger side rear access Pull up on the recliner handle. The seat will lean forward and unlock the track. Slide the seat forward to access the rear area of the cab.
Seating and Safety Restraints REAR SEATS Center facing jump seat (2–door Cab Plus) (if equipped) To open, pull inboard and down on the seat handle. To stow the seat, pull seat bottom back to the fully upright position. WARNING: Do not install a child seat in a center facing jump seat. Center facing jump seat (4 door CabPlus 4) (if equipped) To open, pull seat assembly down, then raise seatback. To stow the seat, fold seat back down and raise seat assembly to the fully upright position.
Seating and Safety Restraints WARNING: It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. Do not allow people to ride in any area of your vehicle that is not equipped with seats and safety belts. Be sure everyone in your vehicle is in a seat and using a safety belt properly.
Seating and Safety Restraints 2. To unfasten, push the release button and remove the tongue from the buckle. The front outboard safety restraints in the vehicle are combination lap and shoulder belts. The front passenger outboard safety belt has two types of locking modes described below: Energy Management Feature • This vehicle has a seat belt system with an energy management feature at the front outboard seating positions to help further reduce the risk of injury in the event of a head-on collision.
Seating and Safety Restraints How to use the automatic locking mode (Outboard front passenger seating position only) for use with child safety seats • Buckle the combination lap and shoulder belt. • Grasp the shoulder portion and pull downward until the entire belt is pulled out. • Allow the belt to retract. As the belt retracts, you will hear a clicking sound. This indicates the safety belt is now in the automatic locking mode.
Seating and Safety Restraints WARNING: BELT AND RETRACTOR ASSEMBLY MUST BE REPLACED if the seat belt assembly “automatic locking retractor” feature or any other seat belt function is not operating properly when checked according to the procedures in Workshop Manual. WARNING: Failure to replace the Belt and Retractor assembly could increase the risk of injury in collisions.
Seating and Safety Restraints • Regular Cab and 4–door Cab Plus • 2–door Cab Plus To lower the shoulder belt height, push the button and slide the height adjuster down. To raise the height of the shoulder belt, slide the height adjuster up. Pull down on the height adjuster to make sure it is locked in place. WARNING: Position the safety belt height adjusters so that the belt rests across the middle of your shoulder.
Seating and Safety Restraints Insert the tongue into the correct buckle (the buckle closest to the direction the tongue is coming from). To lengthen the belt, turn the tongue at a right angle to the belt and pull across your lap until it reaches the buckle. To tighten the belt, pull the loose end of the belt through the tongue until it fits snugly across the hips. Shorten and fasten the belt when not in use to keep the belt away from door openings and available after unfolding the seats.
Seating and Safety Restraints Safety belt extension assembly If the safety belt assembly is too short for you, even when fully extended, 20 cm (8 inches) can be added to the safety belt assembly by adding a safety belt extension assembly. Safety belt extension assemblies can be obtained from your authorized Mazda dealership. Use only extensions manufactured by the same supplier as the safety belt. Manufacturer identification is located at the end of the webbing on the label.
Seating and Safety Restraints BeltMinder The BeltMinder feature is a supplemental warning to the safety belt warning function. This feature provides additional reminders to the driver that the driver’s safety belt is unbuckled by intermittently sounding a chime and illuminating the safety belt warning lamp in the instrument cluster. If...
Seating and Safety Restraints The following are reasons most often given for not wearing safety belts: (All statistics based on U.S. data) Reasons given... 9Crashes are rare events9 9I’m not going far9 9Belts are uncomfortable9 9I was in a hurry9 9Seat belts don’t work9 9Traffic is light9 9Belts wrinkle my clothes9 9The people I’m with don’t wear belts9 78 Consider... 36,700 crashes occur every day. The more we drive, the more we are exposed to 9rare9 events, even for good drivers.
Seating and Safety Restraints Reasons given... 9I have an air bag9 9I’d rather be thrown clear9 Consider... Air bags offer greater protection when used with safety belts. Frontal airbags are not designed to inflate in rear and side crashes or rollovers. Not a good idea. People who are ejected are 40 times more likely to DIE. Safety belts help prevent ejection, WE CAN’T 9PICK OUR CRASH9. WARNING: Always wear the safety belt.
Seating and Safety Restraints WARNING: To reduce the risk of injury, do not deactivate/activate the Belt Minder feature while driving the vehicle. BeltMinder activation and deactivation procedure 1. Turn the ignition switch to the RUN (or ON) position. (DO NOT START THE ENGINE.) 2. Wait until the safety belt warning light turns off. (Approximately 1–2 minutes.) • Steps 3–5 must be completed within 60 seconds or the procedure will have to be repeated. 3.
Seating and Safety Restraints NOTE: If unsure about the proper procedures, bring your vehicle to an authorized Mazda dealership for inspection. Inspect the safety belts to make sure there are no nicks, tears or cuts, replacing if necessary. Check all automatic locking retractors on all outboard seating positions as well as the automatic locking mode for child safety seats on the passenger front belt.
Seating and Safety Restraints AIR BAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS) Important supplemental restraint system (SRS) precautions The supplemental restraint system is designed to work with the safety belt to help protect the driver and right front passenger from certain upper body injuries. WARNING: Air bags DO NOT inflate slowly or gently and the risk of injury from a deploying air bag is greatest close to the trim covering the air bag module. Always wear your safety belt.
Seating and Safety Restraints WARNING: Airbags have been known to kill or injure a child in front facing child restraints. When placing a child safety seat in a front seating position including the center (if equipped), you should turn off the passenger airbag switch after being certain the child is properly restrained. If the child safety seat is in the outboard seating position, slide the seat all the way back. WARNING: Do not install a child seat in a center facing jump seat.
Seating and Safety Restraints • Recline the seat slightly (one or two degrees) from the upright position. WARNING: Do not put anything on or over the air bag module including hands or feet. Placing objects on or over the air bag inflation area may cause those objects to be propelled by the air bag into your face and torso causing serious injury. WARNING: Do not attempt to service, repair, or modify the Air Bag Supplemental Restraint System or its fuses. See your authorized Mazda dealership.
Seating and Safety Restraints WARNING: Never place a rearward facing child safety restraint in front of an airbag. Airbags have been known to kill or injure children in front facing child safety restraints. Whenever placing a child safety seat in a front seating position (including center if equipped), turn off the passenger side air bag switch after being certain the child is properly restrained.
Seating and Safety Restraints How does the air bag supplemental restraint system work? The air bag SRS is designed to activate when the vehicle sustains sufficient longitudinal deceleration. The fact that the air bags did not inflate in a collision does not mean that something is wrong with the system. Rather, it means the forces were not of the type sufficient to cause activation. Air bags are designed to inflate in frontal and near-frontal collisions, not rollover, side-impact, or rear-impacts.
Seating and Safety Restraints WARNING: Several air bag system components get hot after inflation. Do not touch them after inflation or you may be burned. WARNING: If the air bag has deployed, the air bag will not function again and must be replaced immediately. If the air bag is not replaced, the unrepaired area will increase the risk of injury in a collision.
Seating and Safety Restraints If any of these things happen, even intermittently, have the SRS serviced at your authorized Mazda dealership immediately. WARNING: Unless serviced, the system may not function properly in the event of a collision. Disposal of air bags and air bag equipped vehicles (including safety belt pretensioners) For disposal of safety belt pretensioners, air bags, or air bag equipped vehicles, see your authorized Mazda dealership or qualified technician.
Seating and Safety Restraints WARNING: If the OFF light fails to illuminate when the passenger air bag switch is in the OFF position and the ignition switch is in ON, have the passenger air bag switch serviced at you authorized Mazda dealership. WARNING: In order to avoid inadvertent activation of the switch, always remove the ignition key from the passenger air bag ON/OFF switch. Turning the passenger air bag back on The passenger air bag remains OFF until you turn it back ON. 1.
Seating and Safety Restraints WARNING: The safety belts for the driver and right front passenger seating positions have been specifically designed to function together with the air bags in certain types of crashes. When you turn OFF your air bag, you not only lose the protection of the air bag, you also may reduce the effectiveness of your safety belt system, which was designed to work with the air bag.
Seating and Safety Restraints • the infant has a medical condition which, according to the infant’s physician, makes it necessary for the infant to ride in the front so that the driver can constantly monitor the child’s condition. 2. Child age 1 to 12.
Seating and Safety Restraints Transport Canada air bag deactivation criteria (Canada Only) 1. Infant: An infant (less than 1 year old) must ride in the front seat because: • my vehicle has no rear seat; • the rear seat in my vehicle cannot accommodate a rear-facing infant seat; or • the infant has a medical condition which, according to the infant’s physician, makes it necessary for the infant to ride in the front seat so that the driver can monitor the infant’s condition. 2.
Seating and Safety Restraints Transport Canada air bag deactivation criteria (continued) WARNING: This vehicle has special energy management safety belts for the driver and/or right front passenger. These particular belts are specifically designed to work with air bags to help reduce the risk of injury in a collision.
Seating and Safety Restraints WARNING: An air bag can kill or injure a child in a child seat. Child seats should never be placed in the front seats, unless passenger air bag switch is turned off, See Passenger air bag on/off switch. WARNING: Rear facing child seats should NEVER be placed in the front seats unless the passenger airbag switch is turned off. Also, slide the front seat forward until the rear facing child seat contacts the dash board for maximum support.
Seating and Safety Restraints WARNING: Placing a child, 12 years or younger, in the front seat is dangerous. The child could be hit by a deploying air bag and be seriously injured or even killed. Never place a child safety seat in a center facing rear jump seat. If you must place a child safety seat in a front seating position, make sure the passenger airbag is turned off. See Turning the airbag Off in this section.
Seating and Safety Restraints • Can the child stay seated like this for the whole trip? WARNING: Booster seats must be installed only in seating positions equipped with a combination lap/shoulder belt. Types of booster seats There are two types of belt-positioning booster seats: • Those that are backless. If your backless booster seat has a removable shield, remove the shield and use the lap/shoulder belt.
Seating and Safety Restraints The importance of shoulder belts Using a booster without a shoulder belt increases the risk of a child’s head hitting a hard surface in a collision. For this reason, you should never use a booster seat with a lap belt only. It is best to use a booster seat with combination lap/shoulder belts. WARNING: Follow all instructions provided by the manufacturer of the booster seat.
Seating and Safety Restraints When installing a child safety seat: • Review and follow the information presented in the Air Bag Supplemental Restraint System section in this chapter. • Use the correct safety belt buckle for that seating position (the buckle closest to the direction the tongue is coming from). • Insert the belt tongue into the proper buckle until you hear a snap and feel it latch. Make sure the tongue is securely fastened in the buckle.
Seating and Safety Restraints Installing child safety seats with combination lap and shoulder belts (front outboard passenger seat only) 1. Position the child safety seat in a seat with a combination lap and shoulder belt. WARNING: If there is a tether on the child safety seat, attach it to the tether anchor point. Refer to Attaching child safety seats with tether straps in this chapter. WARNING: Air bags can kill or inure a child in a child seat.
Seating and Safety Restraints 2. Pull down on the shoulder belt and then grasp the shoulder belt and lap belt together. 3. While holding the shoulder and lap belt portions together, route the tongue through the child seat according to the child seat manufacturer’s instructions. Be sure the belt webbing is not twisted. 4. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) for that seating position until you hear and feel the latch engage.
Seating and Safety Restraints 5. To put the retractor in the automatic locking mode, grasp the shoulder portion of the belt and pull downward until all of the belt is extracted and a click is heard. 6. Allow the belt to retract. The belt will click as it retracts to indicate it is in the automatic locking mode. 7. Pull the lap belt portion across the child seat toward the buckle and pull up on the shoulder belt while pushing down with knee on the child seat. 8.
Seating and Safety Restraints Attaching child safety seats with tether straps Most new forward-facing child safety seats include a tether strap which goes over the back of the seat and hooks to an anchoring point. Tether straps are available as an accessory for many older safety seats. Contact the manufacturer of your child seat for information about ordering a tether strap. The tether anchors in your vehicle are located on the back of the front seat cushion.
Seating and Safety Restraints WARNING: This anchor information applies to child safety seats equipped with tether straps. For child safety seats equipped with LATCH anchors, refer to Attaching safety seats with LATCH (Lower Anchors and Tethers for Children) attachments for child seat anchors in this chapter. WARNING: Never attach two child safety seat tethers to a single tether anchor.
Seating and Safety Restraints The tether anchor is located on the rear lower portion of the passenger seat. 4. Clip the tether strap to the anchor. WARNING: If the tether strap is clipped incorrectly, the child safety seat may not be retained properly in the event of a collision.
Seating and Safety Restraints Center seating location 60/40 seats with folding armrest When installing a child safety seat in the center position, route the tether strap over the center arm rest and clip it to the center anchor. See next page for center seating location of vinyl 60/40 seat. WARNING: If the tether strap is clipped incorrectly, the child safety seat may not be retained properly in the event of a collision.
Seating and Safety Restraints Center seating location 60/40 vinyl seats When installing a child safety seat in the center position on a 60/40 vinyl seat, route the tether strap through the guiding sleeve and clip it to the center anchor. WARNING: If the tether strap is clipped incorrectly, the child safety seat may not be retained properly in the event of a collision. 5.
Seating and Safety Restraints This type of child seat eliminates the need to use seat belts to attach the child seat. For forward-facing child seats, the tether strap must also be attached to the proper tether anchor. See Attaching safety seats with tether straps in this chapter. Your vehicle may be equipped with LATCH anchors for child seat installation at the following seating positions: • Bucket seats • 60/40 seats represents LATCH anchors. represents tether strap anchors.
Seating and Safety Restraints WARNING: If there are two LATCH seats to install — you can only mount one LATCH seat in this vehicle with the LATCH anchor bars. You need to mount the second seat with the center seat belt using the lap belt method and the child safety seat tether (if equipped). WARNING: Do not attach two seats to one LATCH anchor bar. The lower anchors for child seat installation are located at the rear section of the front passenger seat between the cushion and seat back.
Seating and Safety Restraints Follow the child seat manufacturer’s instructions to properly install a child seat with LATCH attachments. WARNING: Attach LATCH lower attachments of the child seat only to the anchors shown. If you install a child seat with rigid LATCH attachments, do not tighten the tether strap enough to lift the child seat off the vehicle seat cushion when the child is seated in it. Keep the tether strap just snug without lifting the front of the child seat.
Driving STARTING Positions of the ignition 1. ACCESSORY, allows the electrical accessories such as 4 the radio to operate while the 3 engine is not running. 5 2. LOCK, locks the steering wheel, automatic transmission gearshift 2 lever and allows key removal. 3. OFF, shuts off the engine and 1 all accessories without locking the steering wheel. This position also allows the automatic transmission shift lever to be moved from the P (Park) position without the brake pedal being depressed.
Driving WARNING: Do not park, idle, or drive your vehicle in dry grass or other dry ground cover. The emission system heats up the engine compartment and exhaust system, which can start a fire. WARNING: Do not start your vehicle in a closed garage or in other enclosed areas. Exhaust fumes can be toxic. Always open the garage door before you start the engine. See Guarding against exhaust fumes in this chapter for more instructions.
Driving • Make sure the gearshift is in P (Park). If starting a vehicle with a manual transmission: 1. Make sure the parking brake is set. 2. Push the clutch pedal to the floor. 3. Turn the key to 4 (ON) without turning the key to 5 (START). 4 3 5 2 1 If there is difficulty in turning the key, firmly rotate the steering wheel left and right until the key turns freely.
Driving • steering wheel is turned when getting in or out of the vehicle DOOR AJAR CHECK GAGE 4 3 H CHECK ENGINE 5 6 20 1 CHECK FUEL CAP F E ABS 60 70 80 0 0 0 80 100 10 0 ! BRAKE P 40 90 120 60 30 2 C 50 40 RPMx1000 140 000000 20 MPH R N D 2 1 160 100 180 110 km/h 120 THEFT H SPEED CONT L 4WD HIGH H 4WD LOW L O/D OFF Make sure the corresponding lights illuminate or illuminate briefly. If a light fails to illuminate, have the vehicle serviced.
Driving until the engine has warmed up. Consult your fuel distributor for the availability of winter grade (Ed85) ethanol. High-quality blends of winter grade (Ed85) ethanol will produce satisfactory cold weather starting and driving results. Cold starting performance can also be improved by using an engine block heater. Engine block heaters are available as an option and can be obtained from your Mazda dealer. Consult the engine block heater section for proper use of the engine block heater.
Driving WARNING: If you smell exhaust fumes inside your vehicle, have your dealer inspect your vehicle immediately. Do not drive if you smell exhaust fumes. Important ventilating information If the engine is idling while the vehicle is stopped for a long period of time, open the windows at least 2.5 cm (one inch) or adjust the heating or air conditioning to bring in fresh air. BRAKES Occasional brake noise is normal.
Driving WARNING: The Anti-Lock system does not decrease the time necessary to apply the brakes or always reduce stopping distance. Always leave enough room between your vehicle and the vehicle in front of you to stop. Using ABS When hard braking is required, apply continuous force on the brake pedal; do not pump the brake pedal since this will reduce the effectiveness of the ABS and will increase your vehicle’s stopping distance.
Driving The BRAKE warning lamp in the instrument cluster illuminates and remains illuminated (when the ignition is turned ON) until the parking brake is released. ! BRAKE WARNING: Always set the parking brake fully and make sure that the gearshift is securely latched in P (Park) (automatic transmission) or in 1 (First) (manual transmission). NOTE: The parking brake is not recommended to stop a moving vehicle.
Driving • Uneven vehicle loading • High crown in center of road • High crosswinds • Wheels out of alignment • Loose or worn suspension components TRACTION-LOK AXLE/LIMITED SLIP DIFFERENTIAL (IF EQUIPPED) This axle provides added traction on slippery surfaces, particularly when one wheel is on a poor traction surface. Under normal conditions, the Traction-Lok axle functions like a standard rear axle.
Driving WARNING: Loaded vehicles, with a higher center of gravity, may handle differently than unloaded vehicles. Extra precautions, such as slower speeds and increased stopping distance, should be taken when driving a heavily loaded vehicle.
Driving WARNING: Always set the parking brake fully and make sure the gearshift is latched in P (Park). Turn the ignition to the LOCK position and remove the key whenever you leave your vehicle. WARNING: If the parking brake is fully released, but the brake warning lamp remains illuminated, the brakes may not be working properly. See your authorized Mazda dealership.
Driving To put your vehicle in P (Park): • Come to a complete stop • Move the gearshift lever and securely latch it in P (Park) WARNING: Always set the parking brake fully and make sure the gearshift is latched in P (Park). Turn the ignition to the LOCK position and remove the key whenever you leave your vehicle. R (Reverse) With the gearshift lever in R (Reverse), the vehicle will move backward. Always come to a complete stop before shifting into and out of R (Reverse).
Driving 2 (Second) Use 2 (Second) to start-up on slippery roads or to provide additional engine braking on downgrades. 1 (First) • Provides maximum engine braking. • Allows upshifts by moving gearshift lever. • Will not downshift into 1 (First) at high speeds; allows for 1 (First) when vehicle reaches slower speeds. Forced downshifts • Allowed in (Overdrive) or Drive. • Depress the accelerator to the floor. • Allows transmission to select an appropriate gear.
Driving Recommended shift speeds Downshift according to the following charts for your specific engine/drivetrain combination: Upshifts when accelerating (for best fuel economy) Transfer case position (if equipped) Shift from: 2H or 4H 4L 1-2 14 km/h (10 mph) 5 km/h (4 mph) 2-3 32 km/h (22 mph) 11 km/h (9 mph) 3 -4 50 km/h (33 mph) 19 km/h (13 mph) 4 - 5 (Overdrive) 71 km/h (41 mph) 27 km/h (17 mph) Upshifts when cruising (recommended for best fuel economy) Transfer case position (if equipped) Shift from: 2H
Driving Parking your vehicle 1. Apply the brake and shift into the neutral position. 2. Fully apply the parking brake, then shift into 1 (First). 3. Turn the ignition off. WARNING: Do not park your vehicle in Neutral, it may move unexpectedly and injure someone. Use 1 (First) gear and set the parking brake fully. Removing the key Turn the ignition off, push the release lever (located above the ignition), then turn the key toward you and remove the key.
Driving 4WD system indicator lights • 4WD - Illuminates when 4H (4WD High) is engaged. • 4WD LOW – Illuminates when 4L (4WD Low) is engaged. Using the electronic shift 4WD system (if equipped) 2WD 4X4 HIGH 4X4 LOW 2WD (2WD High) - Power to the rear wheels only; used for street and highway driving. 4X4 HIGH (4WD High) - Used for extra traction such as in snow or icy roads or in off-road situations. Not intended for use on dry pavement.
Driving Shifting to/from 4X4 LOW (4WD Low) 1. Bring the vehicle to a complete stop 2. Depress the brake 3. On vehicles equipped with an automatic transmission, place the transmission in N (Neutral); on vehicles equipped with a manual transmission, depress the clutch. 4. Move the 4WD control to the desired position. • If shifting into 4X4 LOW (4WD Low), wait for the LOW RANGE light in the instrument cluster to turn on indicating the shift is complete.
Driving WARNING: Do not spin the wheels at over 56 km/h (35 mph). The tires may fail and injure a passenger or bystander. Sand When driving over sand, try to keep all four wheels on the most solid area of the trail. Do not reduce the tire pressures but shift to a lower gear and drive steadily through the terrain. Apply the accelerator slowly and avoid spinning the wheels. Mud and water If you must drive through high water, drive slowly. Traction or brake capability may be limited.
Driving When descending a steep hill, avoid sudden braking. Shift to a lower gear when added engine braking is desired. When speed control is on and you are driving uphill, your vehicle speed may drop considerably, especially if you are carrying a heavy load. If vehicle speed drops more than 16 km/h (10 mph), the speed control will cancel automatically. Resume speed with accelerator pedal.
Driving SPECIAL LOADING INSTRUCTIONS FOR OWNERS OF PICKUP TRUCKS AND UTILITY-TYPE VEHICLES WARNING: For important information regarding safe operation of this type of vehicle, see the Preparing to drive your vehicle section in this chapter. WARNING: Loaded vehicles may handle differently than unloaded vehicles. Extra precautions, such as slower speeds and increased stopping distance, should be taken when driving a heavily loaded vehicle. Your vehicle can haul more cargo and people than most passenger cars.
Driving determined by subtracting the vehicle curb weight for each engine/transmission combination, any required option weight for trailer towing and the weight of the driver from the GCWR for the towing vehicle. • Maximum Trailer Weight: Maximum weight of a trailer the loaded vehicle (including occupants and cargo) is permitted to tow. It is determined by subtracting the weight of the loaded trailer towing vehicle from the GCWR for the towing vehicle.
Driving Calculating the load your vehicle can carry/tow 1. Use the appropriate maximum GCWR chart (in the Trailer Towing section in this chapter) for your type of engine and rear axle ratio. 2. Weigh your vehicle without cargo. To obtain correct weights, take your vehicle to a shipping company or an inspection station for trucks. 3. Subtract your loaded weight from the maximum GCWR in the chart. This is the maximum trailer weight your vehicle can tow.
Driving 4x2 w/manual transmission For high altitude operation, reduce GCW by 2% per 300 meters (1, 000 ft.) elevation. For definition of terms used in this table see Vehicle Loading earlier in this chapter. To determine maximum trailer weight designed for your particular vehicle, see Calculating the load earlier in this chapter. Maximum trailer weight is shown.
Driving Engine 2.3L 3.0L Dual Sport 4x2 w/automatic transmission Rear axle Maximum Maximum ratio GCWR - kg trailer (lbs.) weight - kg (lbs.) Regular Cab All 2,495 (5,500) 1,025 (2,260) All 3,402 (7,500) 1,823 (4,020) Maximum frontal area of trailer m2 (ft2) Equal to frontal area of vehicle 4.64 (50) Cab Plus/Cab Plus 4 3,402 (7,500) 1,733 (3,820) 3.0L Dual All 4.64 (50) Sport 4.0L Dual All 4,309 (9,500) 2,604 (5,740) 4.
Driving 4x4 w/automatic transmission Rear axle Maximum Maximum Maximum ratio GCWR - kg trailer frontal area (lbs.) weight - kg of trailer (lbs.) m2 (ft2) Regular Cab 3.0L All 3,402 (7,500) 1,742 (3,840) 4.64 (50) Cab Plus/Cab Plus 4 3.0L All 3,402 (7,500) 1,651 (3,640) 4.64 (50) 4.0L All 4,309 (9,500) 2,504 (5,520) 4.64 (50) For high altitude operation, reduce GCW by 2% per 300 meters (1, 000 ft.) of elevation. For definition of terms used in this table, see Vehicle loading earlier in this chapter.
Driving Hitches For towing trailers up to 907 kg (2,000 lb), use a weight carrying hitch and ball which uniformly distributes the trailer tongue loads through the underbody structure. Use a frame-mounted weight distributing hitch for trailers over 907 kg (2,000 lb). Do not install a single or multi-clamp type bumper hitch, or a hitch which attaches to the axle. Underbody mounted hitches are acceptable if they are installed properly. Follow the towing instructions of a reputable rental agency.
Driving Using a step bumper The optional step bumper is equipped with an integral hitch and requires only a ball with a 19 mm (3/4 inch) shank diameter. The bumper has a 907 kg (2,000 lb.) trailer weight and 91 kg (200 lb.) tongue weight capability. The rated capacities (as shown in this guide) for trailer towing with the factory bumper are only valid when the trailer hitch ball is installed directly into the ball hole in the bumper.
Driving Trailer tow connector Color Function 3. Tan/White Tail lamp 4. White Ground Comment Relay controlled circuit activated when the park lamps/headlamps are on. Matching vehicle circuit returns to battery’s negative ground. Driving while you tow When towing a trailer: • Turn off the speed control. The speed control may shut off automatically when you are towing on long, steep grades. • Consult your local motor vehicle speed regulations for towing a trailer.
Driving • Vehicles with trailers should not be parked on a grade. If you must park on a grade, place wheel chocks under the trailer’s wheels. Launching or retrieving a boat Disconnect the wiring to the trailer before backing the trailer into the water. Reconnect the wiring to the trailer after the trailer is removed from the water. When backing down a ramp during boat launching or retrieval: • do not allow the static water level to rise above the bottom edge of the rear bumper.
Driving 4x2 equipped with automatic transmission and 4x4 vehicles: 4x2 vehicles with automatic transmissions or 4x4 vehicles with an electronic-shift transfer case and automatic transmission, follow these guidelines for recreational towing: • Release the parking brake. • Turn the key in the ignition to the OFF/UNLOCKED position. • Place the transmission in N (Neutral). • Do not exceed a distance of 80 km (50 miles). • Do not exceed 56 km/h (35 mph) vehicle speed.
Roadside Emergencies HAZARD FLASHER The hazard flasher is located on the steering column, just behind the steering wheel. The hazard flashers will operate when the ignition is in any position. Push in the flasher control and all front and rear direction signals will flash. Press the flasher control again to turn them off. Use it when your vehicle is disabled and is creating a safety hazard for other motorists. Note: With extended use, the flasher may run down your battery.
Roadside Emergencies This switch is located in the front passenger’s footwell, by the kick panel access cover. To reset the switch: 1. Turn the ignition OFF. 2. Check the fuel system for leaks. 3. If no leaks are apparent, reset the switch by pushing in on the reset button. 4. Turn the ignition ON. 5. Wait a few seconds and return the key to OFF. 6. Make another check of leaks. FUSES AND RELAYS Fuses If electrical components in the vehicle are not working, a fuse may have blown.
Roadside Emergencies Standard fuse amperage rating and color COLOR Fuse rating Mini fuses Standard fuses Maxi fuses 2A 3A 4A 5A 7.5A 10A 15A 20A 25A 30A 40A 50A 60A 70A 80A Grey Violet Pink Tan Brown Red Blue Yellow Natural Green — — — — — Grey Violet Pink Tan Brown Red Blue Yellow Natural Green — — — — — — — — — — — — Yellow — Green Orange Red Blue Tan Natural Passenger compartment fuse panel The fuse panel is located on the left-hand side of the instrument panel facing the driver’s side door.
Roadside Emergencies To remove a fuse use the fuse puller tool provided. The fuses are coded as follows: Fuse/Relay Location 1 2 Fuse Amp Rating 5A 10A 3 4 5 6 7 8 9 7.5A — 15A 2A 7.5A — 7.
Roadside Emergencies Fuse/Relay Location 10 Fuse Amp Rating 7.5A 11 7.5A 12 13 14 — 20A 10A 15 16 — 30A 17 18 19 20A — 25A 20 21 22 23 24 7.5A 15A 20A — 7.5A 25 26 — 10A 27 28 29 — 7.
Roadside Emergencies Fuse/Relay Location 30 31 32 33 Fuse Amp Rating — — — 15A 34 35 — 15A 36 — Passenger Compartment Fuse Panel Description Not used Not used Not used Headlamps, Daytime Running Lamps (DRL) module, Instrument cluster Not used Horn relay (if not equipped with a Central Security Module) Not used Power distribution box The power distribution box is located in the engine compartment.
Roadside Emergencies 2.
Roadside Emergencies Fuse/Relay Location 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 Fuse Amp Rating — — — 40A** 20A** — — — 10A* — 20A* 30A* 10A* — — 30A* — 15A* 20A* — 15A* — — — — 10A* — — 20A* 10A* — Power Distribution Box Description Not used Not used Not used Blower motor Auxiliary cooling fan Not used Not used Not used PCM memory Not used Fuel pump motor Headlamps A/C clutch relay Not used Not used ABS module Not used Trailer Tow Foglamp, Daytime Run
Roadside Emergencies Fuse/Relay Fuse Amp Location Rating 44 — 45A — 45B — 46A — 46B — 47 — 48 — 49 — 50 — 51 — 52 — 53 — 54 — 55 — 56A — 56B — * Mini Fuses ** Maxi Fuses 148 Power Distribution Box Description Not used Wiper HI/LO relay Wiper park/run relay Fuel pump relay Trailer tow relay Starter relay Auxiliary cooling fan relay Not used Not used Not used Not used PCM Diode PCM Relay Blower motor relay A/C clutch relay Front washer pump relay
Roadside Emergencies 3.0L and 4.
Roadside Emergencies Fuse/Relay Location 14 15 16 17 18 19 20 21 Fuse Amp Rating — — 40A** — — — — 10A* 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 — 20A* 30A* 10A* — — 30A* — 15A* 20A* — 15A* — — — — 10A* — — 20A* 10A* — 150 Power Distribution Box Description Not used Not used Blower motor Not used Not used Not used Not used Powertrain Control Module (PCM) memory Not used Fuel pump motor Headlamps A/C clutch solenoid Not used Not used Anti-lock Brake System (ABS) module Not used
Roadside Emergencies Fuse/Relay Fuse Amp Location Rating 44 — 45A — 45B — 46A — 46B — 47A — 47B — 48A — 48B — 51 — 52 — 53 — 54 — 55 — 56 — * Mini Fuses ** Maxi Fuses Power Distribution Box Description Not used Wiper HI/LO relay Wiper park/run relay Fuel pump relay Trailer tow relay A/C clutch solenoid relay Front washer pump relay Fog lamps Fog lamp relay Not used Not used Powertrain Control Module (PCM) Diode Powertrain Control Module (PCM) Blower relay Starter relay OVERHEATING If the temperature gauge
Roadside Emergencies to the ON position without starting the engine. The radiator cooling fans will start to cool the engine. • If neither coolant nor steam is escaping: open the hood and idle the engine until it cools. If this does not lower the temperature, stop the engine and let it cool. 5. Check the coolant level. If it is low, look for leaks in the radiator hoses and connections, heater hoses and connections, radiator and water pump.
Roadside Emergencies Location of the spare tire and tools The spare tire and tools for your vehicle are stowed in the following locations: Tool Spare tire Jack, jack handle, wheel nut wrench Key, spare tire lock (if equipped) Location Under the vehicle, just forward of the rear bumper Regular Cab: behind seats and underneath the jack and tools cover Cab Plus: stowed in the passenger side rear cab compartment or behind the jump seat in a separate tool bag Cab Plus 4–Door: stowed behind the front seats, bet
Roadside Emergencies 2. If equipped, unlock and remove the spare tire carrier lock from the rear access hole located just above the rear bumper and below the tailgate. 3. Insert the straight end of the jack handle into the rear access hole located just above the rear bumper and below the tailgate. Forward motion will stop and resistance to turning will be felt when properly engaged. 4. Turn the handle counterclockwise until tire is lowered to the ground and the cable is slightly slack. 5.
Roadside Emergencies 4. If your vehicle is equipped with P265/75 R15 AT tires, do not stow a flat or inflated full size spare tire in the spare tire carrier. The flat full size tire should be stowed and tied down in the pickup box bed until it can be repaired. 5. If removed, install the spare tire carrier lock on the access hole above the bumper.
Roadside Emergencies 3. Block the diagonally opposite wheel. 4. Insert tapered end of the lug wrench behind hub caps and twist them off. 5. Loosen each wheel lug nut one-half turn counterclockwise but do not remove them until the wheel is raised off the ground. 6. Position the jack according to the following guides and turn the jack handle clockwise until the tire is a maximum of 25 mm (1 inch) off the ground.
Roadside Emergencies • Rear Never use the differential as a jacking point. It is too easy for the vehicle to tilt or fall and you can be injured. 7. Remove the wheel lug nuts with the lug wrench. 8. Replace the flat tire with the spare tire, making sure the valve stem is facing outward. Reinstall the lug nuts until the wheel is snug against the hub. Do not fully tighten the lug nuts until the wheel has been lowered. 9. Lower the wheel by turning the jack handle counterclockwise. 10.
Roadside Emergencies Stowing the flat/spare tire 1. Lay the tire on the ground with the valve stem facing up. 2. Slide the wheel partially under the vehicle and install the wire and retainer through the center of the wheel. 3. Turn the jack handle clockwise until the tire is raised to its original position underneath the vehicle. The effort to turn the jack handle increases significantly as the tire contacts the frame. The spare tire carrier will ratchet when the tire is in the fully stowed position.
Roadside Emergencies Preparing your vehicle When the battery is disconnected or a new battery is installed, the transmission must relearn its shift strategy. As a result, the transmission may have firm and/or soft shifts. This operation is considered normal and will not affect function or durability of the transmission. Over time, the adaptive learning process will fully update transmission operation. 1. Use only a 12–volt supply to start your vehicle. 2.
Roadside Emergencies + + – – 2. Connect the other end of the positive (+) cable to the positive (+) terminal of the assisting battery. + + – – 3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery.
Roadside Emergencies + + – – 4. Make the final connection of the negative (-) cable to an exposed metal part of the stalled vehicle’s engine, away from the battery and the carburetor/fuel injection system. Do not use fuel lines, engine rocker covers or the intake manifold as grounding points. WARNING: Do not connect the end of the second cable to the negative (-) terminal of the battery to be jumped. A spark may cause an explosion of the gases that surround the battery. 5.
Roadside Emergencies Removing the jumper cables + + – – Remove the jumper cables in the reverse order that they were connected. 1. Remove the jumper cable from the ground metal surface. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery. + + – – 2. Remove the jumper cable on the negative (-) connection of the booster vehicle’s battery.
Roadside Emergencies + + – – 3. Remove the jumper cable from the positive (+) terminal of the booster vehicle’s battery. + + – – 4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle’s battery. After the disabled vehicle has been started and the jumper cables removed, allow it to idle for several minutes so the engine computer can relearn its idle conditions.
Roadside Emergencies WRECKER TOWING If you need to have your vehicle towed, contact a professional towing service or, if you are a member, your roadside assistance center. It is recommended that your vehicle be towed with a wheel lift or flatbed equipment. Do not tow with a slingbelt. Mazda Motor Corporation has not approved a slingbelt towing procedure. On 4x2 vehicles, it is acceptable to tow the vehicle with the front wheels on the ground and the rear wheels off the ground.
Customer Assistance CUSTOMER ASSISTANCE (U.S.A.) Your complete and permanent satisfaction is our business. We are here to serve you. All Authorized Mazda Dealers have the knowledge and the tools to keep your Mazda vehicle in top condition.
Customer Assistance CUSTOMER ASSISTANCE (CANADA) Your complete and permanent satisfaction is our business. We are here to serve you. All Authorized Mazda Dealers have the knowledge and the tools to keep your Mazda vehicle in top condition. In our experience, any questions, problems or complaints regarding the operation of your Mazda or any other general service transactions are most effectively resolved by your dealer.
Customer Assistance Please recognize that the resolution of service problems in most cases requires the use of your Mazda dealer’s service facilities. personnel and equipment. We urge you to follow the above three steps in sequence therefore for most effective results. MEDIATION/ARBITRATION PROGRAM Occasionally a customer concern cannot be resolved through Mazda’s Customer Satisfaction Program. If after exhausting procedures in this manual, your concern is still not resolved, you have another option.
Customer Assistance Provincial Administrators may be reached locally as listed below: Province/Territory CAMVAP Number British Columbia & Yukon (604) 681–0312 Territories Alberta & Northwest Territories (403) 426–0650 Saskatchewan (306) 352–9259 Manitoba (204) 942–7166 Ontario (416) 596–8824 Atlantic Canada (902) 422–5413 Quebec (418) 649–1330 REGIONAL OFFICES Regional Offices Mazda Canada Inc. Western Region 8171 Ackroyd Road Suite 2000 Richmond, B.C. V6X 3K1 (604) 303–5670 Mazda Canada Inc.
Customer Assistance CUSTOMER ASSISTANCE (PUERTO RICO) Your complete and permanent satisfaction is our business. That is why all Authorized Mazda Dealers have the knowledge and the tools to keep your Mazda vehicle in top condition. If you have any questions or recommendations for improvement regarding the service of your Mazda vehicle or servicing by Mazda Dealer personnel, we recommend that you take the following steps: STEP 1 Discuss the matter with an Authorized Mazda Dealer.
Customer Assistance MAZDA IMPORTERS/DISTRIBUTORS U.S.A (Importer/Distributor) Mazda North American Operations 7755 Irvine Center Drive Irvine, CA 92618–2922 P.O. Box 19734 Irvine, CA 92623–9734 TEL: 1 (800) 222–5500 (in U.S.A.) (949) 727–1990 (outside U.S.A.) (Distributor in each area) CANADA Mazda Canada Inc. 305 Milner Avenue, Suite 400 Scarborough, Ontario M1B 3V4 Canada TEL: 1 (800) 263–4680 (in Canada) (416) 609–9909 (outside Canada) PUERTO RICO Plaza Motors Corp. (Mazda de Puerto Rico) P.O.
Customer Assistance ADD-ON NON-GENUINE PARTS AND ACCESSORIES Non-genuine parts and accessories for Mazda vehicles can be found in stores. These may fit your vehicle, but they are not approved by the manufacturer for use with Mazda vehicles. When you install non-genuine parts or accessories, they could affect your vehicle’s performance or safety system; the manufacturer’s warranty doesn’t cover this. Before you install any non-genuine parts or accessories, consult an Authorized Mazda Dealer.
Customer Assistance • Tire Warranty NOTE: Detailed warranty information is provided with your Mazda portfolio. OUTSIDE THE UNITED STATES AND CANADA Government regulations in the United States require that automobiles meet specific emission regulations and safety standards. Therefore, vehicles built for use in the United States, its territories, and Canada may differ from those sold in other countries.
Customer Assistance (Note) If you live in the U.S.A., all correspondence to Mazda Motor Corporation should be forwarded to: Mazda North American Operations 7755, Irvine Center Drive Irvine, California 92618–2922 P.O. Box 19734 Irvine, CA 92623–9734 Customer Assistance Center or toll free at 1 (800) 222–5500 If you live outside of the U.S.A., please contact the nearest Mazda Distributor. (See the Mazda Importers/Distributors section of this manual).
Customer Assistance IN CALIFORNIA (U.S. ONLY) California Civil Code Section 1793.
Customer Assistance REPORTING SAFETY DEFECTS (U.S. ONLY) If you believe that your vehicle has a defect that could cause a crash, or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Mazda Corporation. If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign.
Cleaning WASHING YOUR VEHICLE Wash your vehicle regularly with cold or lukewarm water. Never use strong detergents or soap. If your vehicle is particularly dirty, use a quality car wash detergent. Always use a clean sponge, washing glove or similar device and plenty of water for best results. To avoid spots, avoid washing when the hood is still warm, immediately after or during exposure to strong sunlight. During winter months, it is especially important to wash the vehicle on a regular basis.
Cleaning REPAIRING PAINT CHIPS Minor scratches or paint damage from road debris may be repaired with Genuine Mazda Touch-Up Paint. Observe the application instructions on the products. Remove particles such as bird droppings, tree sap, insect remains, tar spots, road salt and industrial fallout immediately. CLEANING THE WHEELS Wash with the same detergent as the body of your vehicle. Do not use acid-based or alcohol-based wheel cleaners, steel wool, fuel or strong detergents.
Cleaning • 2.3L Engine • 3.
Cleaning • 4.0L Engine • Never wash or rinse the engine while it is running; water in the running engine may cause internal damage. CLEANING NON-PAINTED PLASTIC EXTERIOR PARTS Use vinyl cleaner for routine cleaning. Clean with a tar remover if necessary. Do not clean plastic parts with thinners, solvents or petroleum-based cleaners. CLEANING MIRRORS Do not clean your mirrors with a dry cloth or abrasive materials. Use a soft cloth and mild detergent and water.
Cleaning If the wiper still does not wipe properly, this could be caused by substances on the windshield or rear window such as tree sap and some hot wax treatments used by commercial car washes. Clean the outside of the windshield or rear window with a non-abrasive cleaner. Do not use abrasive cleansers on glass as they may cause scratches. The windshield or rear window is clean if beads do not form when you rinse it with water.
Cleaning • Do not use household cleaning products or glass cleaners, which can stain and discolor the fabric and affect the flame retardant abilities of the seat materials. INSIDE WINDOWS Use glass cleaner for the inside windows if they become fogged. Leather seats (if equipped) Your leather seating surfaces have a clear, protective coating over the leather. • To clean, use a soft cloth with Deluxe Leather and Vinyl Cleaner. Dry the area with a soft cloth.
Maintenance and Specifications INTRODUCTION Be extremely careful to prevent injury to yourself and others and damage to your vehicle when using this manual for inspection and maintenance. If you’re unsure about any procedure it describes, we strongly urge you to have a reliable and qualified service shop perform the work, preferably an Authorized Mazda Dealer. Factory-trained Mazda technicians and genuine Mazda parts are best for your vehicle.
Maintenance and Specifications Chart symbols I: Inspect, and if necessary correct, clean or replace A: Adjust R: Replace L: Lubricate Normal driving service intervals – perform at the months or distances shown, whichever occurs first.
Maintenance and Specifications Maintenance Interval (Number of months or km (miles), whichever comes first) Months 4 8 12 16 20 24 28 32 36 40 44 48 x 1000 Miles 5 10 15 20 25 30 35 40 45 50 55 60 Maintenance Item (x 1000 km) (8) (16) (24) (32) (40) (48) (56) (64) (72) (80) (88) (96) Caliper slide rails L L L L Drum brake system, lines and hoses I I I I Exhaust system for leaks, damage, looseness I I Manual transmission fluid Automatic transmission fluid R *2 Exha
Maintenance and Specifications 5. The California Air Resources Board has determined that the failure to perform this maintenance item will not nullify the emission warranty nor limit recall liability prior to completion of the vehicle’s useful life.
Maintenance and Specifications Maintenance Interval (Number of months or Miles (km), whichever comes first) Months 52 56 60 64 68 72 76 80 x 1000 Miles 65 70 75 80 85 90 95 100 105 110 115 120 Maintenance Item (x 1000 km) 84 88 92 (104) (112)(121)(128)(136)(144)(152)(160)(168)(176)(184)(192) Drum brake system, lines and hoses I I Exhaust system for leaks, damage, looseness I I I I Manual transmission fluid Automatic transmission fluid R *2 Exhaust system shielding (for trap
Maintenance and Specifications 4. Refer to vehicle emission control information label for spark plug and gap specifications. 5. The California Air Resources Board has determined that the failure to perform this maintenance item will not nullify the emission warranty nor limit recall liability prior to completion of the vehicle’s useful life.
Suggested Maintenance Interval Towing a trailer or using a camper or car top carrier Extensive idling or low-speed driving for long distances as in heavy commercial use such as delivery, taxi or patrol car Operating in dusty conditions such as unpaved or dusty roads Off road operation 3,000 5,000 15,000 30,000 60,000 As As As 30,000 60,000 miles or miles miles miles miles required required required miles miles 3 months X X X X X X X X X X X X X X X X X For specific recommendations see yo
Maintenance and Specifications While operating your vehicle • Note any changes in the sound of the exhaust or any smell or exhaust fumes in the vehicle. • Check for vibrations in the steering wheel. Notice any increased steering effort or looseness in the steering wheel, or change in this straight ahead position. • Notice if your vehicle constantly turns slightly or “pulls” to one side when traveling on a smooth, level road.
Maintenance and Specifications • Check cooling system fluid level and coolant strength. • Check battery water level (non-maintenance free). • Check battery connections and clean if necessary. SERVICE RECOMMENDATIONS To help you service your vehicle: • We highlight do-it-yourself items in the engine compartment for easy location. • We provide a Scheduled Maintenance section which makes tracking routine service easy.
Maintenance and Specifications Working with the engine on • Automatic transmission: 1. Set the parking brake and shift to P (Park). 2. Block the wheels. • Manual transmission: 1. Set the parking brake, depress the clutch and place the gearshift in N (Neutral). 2. Block the wheels. Note: Do not start your engine with the air cleaner removed and do not remove it while the engine is running. OPENING THE HOOD 1.
Maintenance and Specifications IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 2.3L I4 engine 1. Windshield washer fluid reservoir 2. Engine coolant reservoir 3. Engine oil dipstick 4. Transmission fluid dipstick (automatic transmission) 5. Engine oil filler cap 6. Brake fluid reservoir 7. Power distribution box 8. Clutch fluid reservoir (manual transmission) 9. Battery 10. Power steering fluid reservoir 11.
Maintenance and Specifications 3.0L V6 engine 1 2 3 4 5 6 7 8 11 10 9 1. Engine coolant reservoir 2. Windshield washer fluid reservoir 3. Engine oil filler cap 4. Transmission fluid dipstick (automatic transmission) 5. Engine oil dipstick 6. Brake fluid reservoir 7. Power distribution box 8. Clutch fluid reservoir (manual transmission) 9. Battery 10. Power steering fluid reservoir 11.
Maintenance and Specifications 4.0L SOHC V6 engine 1. Windshield washer fluid reservoir 2. Transmission fluid dipstick (automatic transmission) 3. Engine oil filler cap 4. Engine oil dipstick 5. Brake fluid reservoir 6. Power distribution box 7. Clutch fluid reservoir (manual transmission) 8. Battery 9. Power steering fluid reservoir 10. Air filter assembly 11.
Maintenance and Specifications WINDSHIELD WASHER FLUID Windshield washer fluid Add fluid to fill the reservoir if the level is low. In very cold weather, do not fill the reservoir completely. UID SHER FL WA ON LY RADIATOR COOLANT ONLY Only use a washer fluid that meets Mazda specification . Refer to Lubricant specifications in this chapter. State or local regulations on volatile organic compounds may restrict the use of methanol, a common windshield washer antifreeze additive.
Maintenance and Specifications ENGINE OIL Checking the engine oil Refer to the service maintenance section for the appropriate intervals for checking the engine oil. 1. Make sure the vehicle is on level ground. 2. Turn the engine off and wait a few minutes for the oil to drain into the oil pan. 3. Set the parking brake and ensure the gearshift is securely latched in P (Park) (automatic transmission) or 1 (First) (manual transmission). 4. Open the hood. Protect yourself from engine heat. 5.
Maintenance and Specifications • 3.0L V6 engine • 4.
Maintenance and Specifications 6. Wipe the indicator clean. Insert the indicator fully, then remove it again. • If the oil level is between the MIN and MAX marks, the oil level is acceptable, DO NOT ADD OIL. • If the oil level is below the MIN mark, add enough oil to raise the level within the MIN-MAX range. • 2.3L I4 engine SAE 5W-20 • 3.
Maintenance and Specifications • 4.0L SOHC V6 engine SAE 5W-30 • Oil levels above the MAX mark may cause engine damage. Some oil must be removed from the engine by a service technician. 7. Put the indicator back in and ensure it is fully seated. Adding engine oil 1. Check the engine oil. For instructions, refer to Checking the engine oil in this chapter. 2. If the engine oil level is not within the normal range, add only certified engine oil of the recommended viscosity.
Maintenance and Specifications Engine Oil Recommendations 2.3L & 3.0L Engines Look for this certification trademark. SAE 5W-20 engine oil is recommended. Only use oils “Certified For Gasoline Engines” by the American Petroleum Institute (API). Use an equivalent oil Mazda specification. SAE 5W-20 oil provides optimum fuel economy and durability performance meeting all requirements for your vehicle’s engine.
Maintenance and Specifications 4.0L Engine Look for this certification trademark. SAE 5W-30 engine oil is recommended. Only use oils “Certified For Gasoline Engines” by the American Petroleum Institute (API). Use an equivalent Mazda Specification. Do not use supplemental engine oil additives, oil treatments or engine treatments. They are unnecessary and could, under certain conditions, lead to engine damage which is not covered by your warranty.
Maintenance and Specifications BATTERY Your vehicle is equipped with a Mazda maintenance-free battery which normally does not require additional water during its life of service. However, for severe usage or in high temperature climates, check the battery electrolyte level. Refer to the service maintenance section for the service interval schedules. Keep the electrolyte level in each cell up to the “level indicator”. Do not overfill the battery cells.
Maintenance and Specifications WARNING: When lifting a plastic-cased battery, excessive pressure on the end walls could cause acid to flow through the vent caps, resulting in personal injury and/or damage to the vehicle or battery. Lift the battery with a battery carrier or with your hands on opposite corners. WARNING: Keep batteries out of reach of children. Batteries contain sulfuric acid. Avoid contact with skin, eyes or clothing.
Maintenance and Specifications will not affect function or durability of the transmission. Over time the adaptive learning process will fully update transmission operation to its optimum shift feel. TU LE AD RE If the battery has been disconnected or a new battery has been installed, the clock and the preset radio stations must be reset once the battery is reconnected. • Always dispose of automotive batteries in a responsible manner. Follow your local authorized standards for disposal.
Maintenance and Specifications • 2.3L engine • 3.0L & 4.0L engines RADIATOR COOLANT ONLY When the engine is cold, check the level of the engine coolant in the reservoir. • The engine coolant should be at the “cold fill level” or within the “cold fill range” as listed on the engine coolant reservoir (depending upon application). • Refer to the service maintenance section for service interval schedules. • Confirm the color and type of engine coolant before adding, to avoid mixing uncompatible products.
Maintenance and Specifications WARNING: Automotive fluids are not interchangeable; do not use engine coolant, antifreeze or windshield washer fluid outside of its specified function and vehicle location. Adding engine coolant Use only Mazda Genuine Engine Coolant or a premium engine coolant that meets a Mazda specification. • DO NOT USE Extended Life Engine Coolant (orange in color). • DO NOT USE a DEX-COOLt engine coolant or an equivalent engine coolant.
Maintenance and Specifications Check the coolant level in the reservoir before you drive your vehicle the next few times (with the engine cool). If necessary, add a 50/50 mixture of engine coolant and distilled water to the engine coolant reservoir until the coolant level is at the “cold fill level” or within the “cold fill range” as listed on the reservoir (depending upon application). Have your dealer check the engine cooling system for leaks if you have to add more than 1.0 liter (1.
Maintenance and Specifications • It may be necessary to increase the coolant concentration above 50%. • NEVER increase the coolant concentration above 60%. • Increased engine coolant concentrations above 60% will decrease the overheat protection characteristics of the engine coolant and may cause engine damage. • Refer to the chart on the coolant container to ensure the coolant concentration in your vehicle will provide adequate freeze protection at the temperatures in which you drive in the winter months.
Maintenance and Specifications WARNING: The fuel system may be under pressure. If the fuel filler cap is venting vapor or if you hear a hissing sound, wait until it stops before completely removing the fuel filler cap. Otherwise, fuel may spray out and injure you or others. WARNING: If you do not use the proper fuel filler cap, excessive pressure or vacuum in the fuel tank may damage the fuel system or cause the fuel cap to disengage in a collision, which may result in possible personal injury.
Maintenance and Specifications clothing and wash skin thoroughly with soap and water. Repeated or prolonged skin contact with fuel liquid or vapor causes skin irritation. • Be particularly careful if you are taking “Antabuse” or other forms of disulfiram for the treatment of alcoholism. Breathing gasoline and/or ethanol vapors, or skin contact could cause an adverse reaction. In sensitive individuals, serious personal injury or sickness may result.
Maintenance and Specifications WARNING: Flexible fuel components and standard unleaded gasoline fuel components are not interchangeable. If your vehicle is not serviced in accordance with flexible fuel vehicles procedures, damage may occur and your warranty may be invalidated. WARNING: When refueling always shut the engine off and never allow sparks or open flames near the filler neck. Never smoke while refueling. Fuel vapor is extremely hazardous under certain conditions.
Maintenance and Specifications 4. To install the cap, align the tabs on the cap with the notches on the filler pipe. 5. Turn the filler cap clockwise 1/8 of a turn until it stops. “Check Fuel Cap” illuminates when the ignition is turned to the ON position to ensure your bulb is working. When this light turns on, check the fuel filler cap. Continuing to operate the vehicle with the Check Fuel Cap light on, can activate the Service Engine Soon warning.
Maintenance and Specifications Octane recommendations Do not be concerned if your engine sometimes knocks lightly. However, if it knocks heavily under most driving conditions while you are (R+M)/2 METHOD using fuel with the recommended octane rating, see your authorized Mazda dealership to prevent any engine damage. Unleaded Gasoline engines Your vehicle is designed to use “Regular” unleaded gasoline with an (R+M)/2 octane rating of 87.
Maintenance and Specifications Unleaded Gasoline engines If you are experiencing starting, rough idle or hesitation driveability problems during a cold start, try a different brand of “Regular” unleaded gasoline. “Premium” unleaded gasoline is not recommended (particularly in the United States) because it may cause these problems to become more pronounced. If the problems persist, see your authorized Mazda dealership.
Maintenance and Specifications Replace the fuel filter with an authorized Mazda part. The customer warranty may be void for any damage to the fuel system if an authorized Mazda fuel filter is not used. ESSENTIALS OF GOOD FUEL ECONOMY Measuring techniques Your best source of information about actual fuel economy is you, the driver. You must gather information as accurately and consistently as possible. Fuel expense, frequency of fillups or fuel gauge readings are NOT accurate as a measure of fuel economy.
Maintenance and Specifications • Have the vehicle loading and distribution the same every time. Your results will be most accurate if your filling method is consistent. Calculating fuel economy 1. Fill the fuel tank completely and record the initial odometer reading (in kilometers or miles). 2. Each time you fill the tank, record the amount of fuel added (in liters or gallons). 3. After at least three to five tank fill-ups, fill the fuel tank and record the current odometer reading. 4.
Maintenance and Specifications • Revving the engine before turning it off may reduce fuel economy. • Using the air conditioner or defroster may reduce fuel economy. • You may want to turn off the speed control in hilly terrain if unnecessary shifting between third and fourth gear occurs. Unnecessary shifting of this type could result in reduced fuel economy. • Warming up a vehicle on cold mornings is not required and may reduce fuel economy.
Maintenance and Specifications • Four-wheel-drive operation (if equipped) is less fuel efficient than two-wheel-drive operation. • Close windows for high speed driving. EPA window sticker Every new vehicle should have the EPA window sticker. Contact your dealer if the window sticker is not supplied with your vehicle. The EPA window sticker should be your guide for the fuel economy comparisons with other vehicles. It is important to note the box in the lower left corner of the window sticker.
Maintenance and Specifications Illumination of the “Service Engine Soon” light, charging system warning light or the temperature warning light, fluid leaks, strange odors, smoke or loss of engine power, could indicate that the emission control system is not working properly. WARNING: Exhaust leaks may result in entry of harmful and potentially lethal fumes into the passenger compartment. Do not make any unauthorized changes to your vehicle or engine.
Maintenance and Specifications CHECKING AND ADDING POWER STEERING FLUID • 2.3L I4 engine • 3.0L V6 engine • 4.
Maintenance and Specifications Check the power steering fluid. Refer to the service maintenance section for the service interval schedules. If adding fluid is necessary, use only MERCONt ATF. 1. Start the engine and let it run until it reaches normal operating temperature (the engine coolant temperature gauge indicator will be near the center of the normal area between H and C). 2. While the engine idles, turn the steering wheel left and right several times. 3. Turn the engine off. 4.
Maintenance and Specifications 2. Visually inspect the fluid level. 3. If necessary, add brake fluid from a clean un-opened MAX container until the level reaches MAX. Do not fill above this line. 4. Use only a DOT 3 brake fluid certified to meet Mazda specification . Refer to Lubricant specifications in this chapter. WARNING: Brake fluid is toxic. If brake fluid contacts the eyes, flush eyes with running water for 15 minutes. Seek medical attention if irritation persists.
Maintenance and Specifications 1. Clean the reservoir cap before removal to prevent dirt and water from entering the reservoir. 2. Remove cap and rubber diaphragm from reservoir. 3. Add fluid until the level reaches the step in the reservoir. 4. Reinstall rubber diaphragm and cap onto reservoir. TRANSMISSION FLUID Checking automatic transmission fluid (if equipped) Refer to your service maintenance section for scheduled intervals for fluid checks and changes. Your transmission does not consume fluid.
Maintenance and Specifications 6. Install the dipstick making sure it is fully seated in the filler tube. 7. Remove the dipstick and inspect the fluid level. The fluid should be in the designated area for normal operating temperature or ambient temperature. Low fluid level Do not drive the vehicle if the fluid level is at the bottom of the dipstick and the ambient temperature is above 10°C (50°F).
Maintenance and Specifications Use of a non-approved automatic transmission fluid may cause internal transmission component damage. If necessary, add fluid in 250 ml (1/2 pint) increments through the filler tube until the level is correct. If an overfill occurs, excess fluid should be removed by a qualified technician. An overfill condition of transmission fluid may cause shift and/or engagement concerns and/or possible damage.
Maintenance and Specifications 6. Fluid level should be at the bottom of the opening. 7. Add enough fluid through the filler opening so that the fluid level is at the bottom of the opening. 8. Install and tighten the fill plug securely. Use only fluid that meets Mazda specifications. Refer to Lubricant Specifications in this chapter. Checking and adding transfer case fluid (if equipped) Vehicle must be on level surface. 1. Clean the filler plug. 2. Remove the filler plug and inspect the fluid level. 3.
Maintenance and Specifications Use only fluid that meets Mazda specifications. Refer to Lubricant Specifications in this chapter. DRIVELINE UNIVERSAL JOINT AND SLIP YOKE Your vehicle may be equipped with universal joints that require lubrication. If the original universal joints are replaced with universal joints equipped with grease fittings, lubrication will also be necessary.
Maintenance and Specifications Traction AA A B C The traction grades, from highest to lowest are AA, A, B, and C. The grades represent the tire’s ability to stop on wet pavement as measured under controlled conditions on specified government test surfaces of asphalt and concrete. A tire marked C may have poor traction performance.
Maintenance and Specifications Tire rotation Because your vehicle’s tires perform different jobs, they often wear differently. To make sure your tires wear evenly and last longer, rotate them as indicated in the service maintenance section. If you notice that the tires wear unevenly, have them checked. The following procedure applies to vehicles equipped with single rear wheels, if your vehicle is equipped with dual rear wheels it is recommended that only the front wheels be rotated (side to side).
Maintenance and Specifications Replacing the tires Replace the tires when the wear band is visible through the tire treads. WARNING: When replacing full size tires, never mix radial bias-belted, or bias-type tires. Use only the tire sizes that are listed on the Certification Label. Make sure that all tires are the same size, speed rating, and load-carrying capacity. Use only the tire combinations recommended on the label.
Maintenance and Specifications SNOW TIRES AND CHAINS WARNING: Driving too fast for conditions creates the possibility of loss of vehicle control. Driving at very high speeds for extended periods of time may result in damage to vehicle components. NOTE: Snow tires must be the same size and grade as the tires you currently have on your vehicle. The tires on your vehicle have all weather treads to provide traction in rain and snow. However, in some climates, you may need to use snow tires and chains.
Maintenance and Specifications REFILL CAPACITIES Fluid Engine oil (includes filter change) Brake fluid Power steering fluid Transmission fluid 1 232 Mazda Part Name Mazda SAE 5W20 Super Premium Motor Oil Mazda SAE 5W30 Super Premium Motor Oil High Performance DOT 3 Motor Vehicle Brake Fluid Mazda MERCONt ATF Mazda MERCONt ATF Mazda MERCONtV ATF Application Capacity 2.3L engine 3.8L (4.0 quarts.) 4.3L (4.5 quarts) 4.7L (5.0 quarts) 3.0L V6 engines 4.
Maintenance and Specifications Fluid Engine coolant Fuel tank Transfer Case Fluid Front axle lubricant 4 Mazda Part Application Name Premium Engine 2.3 L I4 engine Coolant with manual transmission 2.3L I4 engine with automatic transmission 3.0L V6 engine with manual transmission 3.0L V6 engine with automatic transmission 4.0L V6 engine with manual transmission 4.
Maintenance and Specifications Fluid Rear axle lubricant5 Windshield washer fluid Mazda Part Name Mazda SAE 80W-90 Premium Rear Axle Lubricant Ultra-Clear Windshield Washer Concentrate Application Capacity All 2.4-2.5L (5.0-5.3 pints) All 2.6L (2.75 quarts) 1 Ensure the correct automatic transmission fluid is used. Transmission fluid requirements are indicated on the dipstick or on the dipstick handle. MERCONt and MERCONt V are not interchangeable. DO NOT mix MERCONt and MERCONtV.
Maintenance and Specifications LUBRICANT SPECIFICATIONS Item Front axle (4X4) Rear axle Brake fluid and clutch fluid (if equipped) Door weather strips Engine coolant Engine oil 2.3L I4 and 3.0L V6 engines Engine oil 4.
Maintenance and Specifications handle. MERCONt and MERCONt V are not interchangeable. DO NOT mix MERCONt and MERCONt V. Refer to your service maintenance section to determine the correct service interval. 3 Do not mix different types or colors of engine coolant. ENGINE SPECIFICATIONS Engine Cubic inches Required fuel Firing order Spark plug gap Ignition system Compression ratio 2.3L I4 engine 138 87 octane 1-3-4-2 1.04-1.19mm (0.041-0.047 inch) EDIS 9.7:1 3.0L V6 engine 182 87 octane 1-4-2-5-3-6 1.
Maintenance and Specifications 3 5 2 4 1 237
Maintenance and Specifications 4 1 IDENTIFYING YOUR VEHICLE Certification label The National Highway Traffic Safety Administration Regulations require that a Certification Label be affixed to a vehicle and prescribe where the Certification Label may be located. The Certification Label is located on the front door latch pillar on the driver’s side. Vehicle identification number (VIN) The vehicle identification number is attached to a metal tag and is located on the driver side instrument panel.
Accessories CELL PHONES Use of cell phones and other devices by driver: WARNING: Use of any electrical devices such as cell phones, computers, portable radios, vehicle navigation or other devices by the driver while the vehicle is moving is dangerous. Dialing a number on a cell phone while driving also ties-up the driver’s hands. Use of these devices will cause the driver to be distracted and could lead to a serious accident.
Index A ABS (see Brakes) .....................115 Air bag supplemental restraint system ..........................................82 and child safety seats ..............84 description ................................82 disposal ......................................88 driver air bag ............................86 indicator light ...........................87 operation ...................................86 passenger air bag .....................86 passenger deactivation switch ..............................
Index instrument cluster lens ..........180 instrument panel ....................180 interior .....................................180 Mazda car care products .......181 mirrors .....................................179 plastic parts ............................179 washing ....................................176 waxing .....................................176 wheels ......................................177 windows ..................................181 wiper blades ............................
Index driving off road .......................126 electronic shift ........................125 indicator light .........................125 preparing to drive your vehicle .....................................118 Fuel ............................................208 calculating fuel economy .......215 cap ...........................................211 capacity ...................................232 choosing the right fuel ...........212 comparisons with EPA fuel economy estimates .................
Index Jump-starting your vehicle ......158 K Keys positions of the ignition .........110 Mirrors automatic dimming rearview mirror ........................................50 cleaning ...................................179 side view mirrors (power) .......53 Motorcraft parts ........................214 L Lamps bulb replacement specifications chart ..................40 cargo lamps ...............................39 daytime running light ...............38 fog lamps ...................................
Index S Safety belts (see Safety restraints) .........69–73 Safety defects, reporting ..........175 Safety restraints ....................69–73 belt minder ...............................77 cleaning the safety belts ..........80 extension assembly ..................76 for adults .............................70–72 for children .........................93–94 lap belt ......................................74 warning light and chime ..........76 Safety restraints - LATCH anchors ................................
Index W Warning lights (see Lights) .......12 Washer fluid ..............................195 Washing your vehicle ................176 Water, Driving through .............128 Waxing your vehicle .................176 Windows power .........................................49 Windshield washer fluid and wipers ..........................................47 checking and adding fluid .....195 checking and cleaning ..............47 replacing wiper blades .............48 Wrecker towing .........................
