MULTICOM STATIONARY 2.
1. General Information 1.1 Introduction The "Multicom Stationary 2.4G" is designed by using the most advanced Multiplex communication technology. It serves user-friendly features and extremely convenient to operate including a crystal clear sound quality and also long distance communication coverage.
2. Controls and Indicators LCD Down Button Mode Button UP Button Ear / MIC XLR-4PINs (Desk top Mic. IN) Power S.W Antenna Jack USB XLR-3PINs 55 Jack (Audio IN) Power S.
3. How to use 3.1 Power On/Off Press the "Power S.W" switch to the upward to turn the stationary power on. The LCD display is on and shows the default volume level with "VOL 03". If you pressed the "Power S.W" to the downward, the stationary power is turned off. 3.2 Volume Up / Down It gives you to adjust the hearing volume level with 9 steps as per you prefer. Press "▲" button to control volume up and "▼" button for volume down after turn the device power on.
3.4 ID selection In a group, every Stationary needs to have each different ID per Stationary from "00" to "99". The ID "00" becomes a master device in a group and every group needs to have a master device with ID "00" per group without alternative. The "MASTER" is displaying on the LCD as soon as the ID "00" is set. Press and hold the "Mode" button longer than 3 seconds after turn the device power on. The "GRP" symbol on the LCD is blinking. And press the "Mode" button one more time instantly.
Normal Audio Output mode Loud Audio Output mode Note; 1) Its default setting is "UL". 2) There might be a kind of white noise creation when you set the audio output at "UH". Hence, it is recommendable to set the audio output at "UL" except using the device at the heavy noise surround place. It is available to select the microphone sensitivity up to 5 steps according to the environment you have. Press and hold the "Mode" button longer than 3 seconds after turn the device power on.
4. Specifications ITEM SPECIFICATION Radio Frequency Type ISM 2405MHz ~ 2477MHz Type Wireless Microphone/Receiver Unit Radio Interface ISM 2.4GHz: FSK Modulation with Frequency Hopping Voice Codec 16bit/8KHz Tx Max. Output Power 10dBm RX Sensitivity -95dBm Voice Latency <35ms Num. of Frequency Channel 145CH Operation Hopping 16CH Channel Spacing 0.5MHz Data Rate 0.5Mbps Freq. Bandwidth 2MHz Power Supply Output Voltage: DC 5.
5. How to install 5.1 General Publishing Speaking only or Speaking and Listening 100~ 400m distance Unlimited Listeners with MTT-R Notice) It is required to tune the same group number only between Stationary and MTT-R Listening device regardless its ID number. 5.2 Full duplex communication with up to two other MTT-T devices Stationary MTT-T 1 100~ 400m distance MTT-T 2 Notice) It is required to tune the same group number between Stationary and two other MTT-T devices.
5.3 Full duplex communication and general publishing Stationary MTT-T 1 MTT-T 2 Full Duplex communications between Stationary, MTT-T1 and MTT-T2 Listening all the talking between Stationary, MTT-T1 and MTT-T2 Unlimited number of Listeners with MTT-R 5.4 Line repeat communication between Stationary and Stationary It is available to repeat the communication in one Stationary to the other Stationary by cable connection between two stationeries.
FCC Information to User This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. 5) Do not use this equipment near water. 6) Do not using near any heat sources such as radiators, heat resisters, stove, or other equipment that produce heat. European CE notice to users and product statements This product is CE marked according to the provisions of the R&TTE Directive(1999/5/EC). Hereby, Maytel Co.
CONTACT INFORMATION Manufacturer Address #417 Doosan Venture Digm 126-1, Pyeongchon-dong, Dongan-gu, Anyang-si, Gyeonggi-do, Republic of Korea To locate in-country MAYTEL CO., LTD., distributors of the Multicom Stationary 2.4G (MTT Stationary T-1) please refer to the MAYTEL CO., LTD. Website http:// www.maytel.com These distributor(s) represent local contacts for this product. CORPORATE HEADQUARTERS: MAYTEL CO., LTD.
EUROPEAN UNION “DECLARATION OF CONFORMITY” DECLARATION OF CONFORMITY MAYTEL CO., LTD. #417 Doosan Venture Digm 126-1, Pyeongchon-dong, Dongan-gu, Anyang-si, Gyeonggi-do, Republic of Korea declare under our sole responsibility that the product(s) Multicom Stationary 2.4G (MTT Stationary T-1) – MS-11 2.4G to which this declaration relate(s) is in conformance with the following standards: EN 301 489-1 V1.9.2:2011 EN 301 489-17 V2.2.1:2012 EN 60950-1:2006/A2:2013 EN 300 328 V1.9.