Specifications

ManualsBrandsMaytag ManualsDryerLDE8604AAL

W10214569B

www.maytagcommerciallaundry.com

INSTALLATION INSTRUCTIONS

MFS80, MFS100, MFS125, MFS180, MFS230, MFS275

COMMERCIAL WASHER

TABLE OF CONTENTS

WASHER SAFETY .................................................................. 2

INSTALLATION REQUIREMENTS ......................................... 3

Tools, Parts, and Equipment ................................................. 3

Location Requirements ........................................................ 3

Electrical Requirements ......................................................... 6

Water Supply Requirements ................................................. 7

Drain Requirements .............................................................. 7

INSTALLATION INSTRUCTIONS ........................................... 8

Transport, Handling, Inspection, and Storage ...................... 8

Moving to Final Location ...................................................... 8

Water, Drain, and Venting Connections ................................ 9

Electrical Connection ......................................................... 10

Remove Shipping Brackets ................................................ 13

Complete Installation .......................................................... 15

Break-In Period .................................................................. 15

Controls Troubleshooting ................................................... 15

WASHER MAINTENANCE ................................................... 16

Maintenance Schedule ........................................................ 16

Vibration Switch Adjustment and Function Test ................. 17

Belt Inspection, Adjustment, and Replacement .................. 18

Tightening Moments ............................................................ 19

Lubrication .......................................................................... 20

Water and Steam Filters ..................................................... 20

Thrust of Door Seal ............................................................. 21

Spring Unit .......................................................................... 22

Fuse Capacities ..................................................................... 22

Earth Leakage Trips ...............................................................22

TROUBLESHOOTING .............................................................23

REMOVING THE WASHER FROM SERVICE.........................24

DIMENSIONS AND TECHNICAL SPECIFICATIONS .............25

Models MFS80, MFS100, and MFS125 ..............................25

Dimensions and Connections ...........................................26

Torque Specications ........................................................ 26

Technical Specications .................................................... 27

Model MFS180 .....................................................................29

Dimensions and Connections ...........................................30

Torque Specications ........................................................ 30

Models MFS230 and MFS275 .............................................31

Dimensions and Connections ...........................................32

Torque Specications ........................................................ 32

Technical Specications

(Models MFS180, MFS230, and MFS275) ........................33

Models MFS230 and MFS275

with Tilting Feature ..............................................................35

Dimensions and Connections ...........................................35

Technical Specications ................................................... 35

Summary of content (36 pages)

PAGE 1
INSTALLATION INSTRUCTIONS MFS80, MFS100, MFS125, MFS180, MFS230, MFS275 COMMERCIAL WASHER TABLE OF CONTENTS WASHER SAFETY ................................................................... 2 INSTALLATION REQUIREMENTS.......................................... 3 Tools, Parts, and Equipment.................................................. 3 Location Requirements ......................................................... 3 Electrical Requirements..........................................................
PAGE 2
WASHER SAFETY IMPORTANT: ■■ ■■ ■■ 2 This washer must be directly wired to the electrical system and may not be attached with a plug. The circuit must be a dedicated circuit and may not be combined with any lighting circuit. Adequate grounding is essential to washer operation.
PAGE 3
INSTALLATION REQUIREMENTS Location Requirements Tools, Parts, and Equipment Read and follow the instructions provided with any tools listed here. Tools Needed Washers must be installed by professional installers, who should have a full compliment of standard SAE and metric hand tools, and specialized tools as required. Gather the required tools and parts before starting installation. Washers must be installed on a level concrete floor on the ground level of a building.
PAGE 4
Spacing Spacing Between Multiple Washers and Feet Placement ■■ Washers require 2.4 ft (0.7 m) above the top for maintenance. ■■ Washers require 2.4 ft (0.7 m) (Models MFS80/MFS100/ MFS125) and 2.6 ft (0.8 m) (Models MFS180/MFS230/ MFS275) between the sides for maintenance and maximum door clearance. X4 1 2 X12 Allow 3.3 ft (1 m) behind washer and the wall for maintenance. 3 X13 ■■ Models MFS80, MFS100, MFS125 Models MFS80, MFS100, MFS125 4 X6 X15 X1 X2 X14 X5 700 mm 28" 2.
PAGE 5
Models MFS180, MFS230, MFS275 Spacing Between Multiple Washers and Feet Placement Models MFS180, MFS230, MFS275 2.3 ft 28" (711 mm) (0.7 m) 2.6 ft (0.8 P m) 2.6 ft (0.8 m)P Front View X1 X2 1 2 SideView View Side 1. Drain hose 2. Waste sump cover 3. Waste sump 3 X3 Dimensions X1 X2 X3 X13 27.55" (700 mm) 39.36" (1000 mm) 16.33" (415 mm) 9.84" (250 mm) 1. Washer contour line 2. Washer foot 3. Waste sump 4. Drain hose Feet Placement Distance MS180 MS230 X1 49.99" 54.
PAGE 6
Electrical Requirements Washer Connection to Electrical Network (With an Earth Leakage Trip) It Is Your Responsibility: ■■ ■■ ■■ To contact a qualified electrical installer. To be sure that the electrical connection is adequate and in conformance with the National Electrical Code, ANSI/NFPA 70-latest edition, or Canadian Electrical Code CSA C22.1, and all local codes and ordinances.
PAGE 7
Connection of the Main Power Inlet Water Supply Requirements Water supply requirements are as follows: 1 ■■ Valved hot and cold water supply with a water pressure between 14.5 and 116 PSI (100–800 kPa). Water pressure between 43 and 73 PSI (300–500 kPa) is recommended. ■■ A hot water heater or boiler supplying an adequate amount of water between 120–160°F (49–80°C). The water temperature within the washer is controlled to a maximum temperature that is set in the program.
PAGE 8
INSTALLATION INSTRUCTIONS Transport, Handling, Inspection, and Storage Models MFS80, MFS100, MFS125 4 2 NOTE: Refer to "Equipment for Handling, Transport, and Storage" under "Tools, Parts, and Equipment" for proper handling of washer. 1. I nspect carton for damage. Inspect washer if carton shows signs of damage. Do not remove washer from pallet. 2. Verify model number and serial number on the data plate with your order. Remove accessories and manuals from inside washer drum. 3.
PAGE 9
Water, Drain, and Venting Connections Water Hardness Drain Connections Determine the water hardness level in water supply. Good wash results are dependent on water hardness. In areas that have medium and very hard water levels, a water softener may be required. Contact your water or soap distributor for determining the proper soap and detergents to be used with your hardness levels for the best wash results. 1. Always use the flexible hoses delivered with the washer.
PAGE 10
Electrical Connection Washer Connection to Electrical Network (with a residual current device) 1 2 3 Check the data plate to determine electrical requirements. Before making the electrical connection, make sure the voltage and frequency listed on the data plate matches your electrical network. Each washer must be on an individual branch circuit.
PAGE 11
Residual Current Device (RCD) ■■ In some countries an RCD is known as an “earth leakage trip,” “Ground Fault Circuit Interrupter” (GFCI), “Appliance Leakage Current Interrupter” (ALCI), or “earth (ground) leakage current breaker.” Specifications: ■■ Tripping current: 100mA (if locally not available/allowed use a 30mA trip current, preferably selective type with small time delay set).
PAGE 12
Washer Earth Connection and Equipotential Bonding Connecting Liquid Soap Supply Systems Independent of the supply cable, the washer must be connected to the laundry earth system with a separate conductor. The protective conductor, which enables this connection, is not included with the washer. If there are other washers/appliances with exposed conductive parts which can be touched simultaneously, make equipotential bonding between all of these appliances.
PAGE 13
Electrical Connection Remove Shipping Brackets The power supply of the liquid soap pump system must be connected to an external electrical source. Only qualified technicians can make the electrical connection according to local codes. Instructions for the correct connection can be found on the wiring diagram located in a plastic bag inside the cabinet. Do not connect the liquid soap pump system in the washer. IMPORTANT: Shipping brackets must be removed before putting the washer into service.
PAGE 14
Remove Shipping Brackets (cont.) Models MFS180, MFS230, MFS275 1. Remove the rear lower panel and side panels. 2. Remove the rear shipping bracket (1), the three left-side shipping brackets (2), and the three right-side shipping brackets (3). Retain brackets and bolts if needed to secure the washer for transport in the future. 3. Replace panels.
PAGE 15
5. Remove the film covering from the cabinet. Complete Installation 6. Make sure the waste sump is ready for water drainage. 7. Open door and make sure that the washer drum is empty. 8. Verify that washer is level and does not rock from side-to-side. 9. Check electrical connection and ground – PE or PEN. 10. A djust vibration switch. See “Vibration Switch Adjustment” in Maintenance. 11. Check drain connection and clearance. 12. Turn power on at circuit breaker. 13. T urn the washer on.
PAGE 16
WASHER MAINTENANCE Maintenance Schedule After Each Load ■■ Remove debris from the wash drum including paper clips, coins, and other hard items. ■■ When not in use, leave the washer door open to allow the washer to air out and prolong gasket life. Daily Maintenance ■■ Clean water, detergent, and other stains off of the washer with a soft cloth dampened with a mild detergent solution. ■■ Dry with a soft cloth. Do not use abrasives.
PAGE 17
Vibration Switch Adjustment and Function Test 5. M oving the holder (7) with the switch left or right will center the switch control element in the limiter’s rubber bushing. C 5 B 3 5 2 6 A 1 7 2 4 4 1 Front view Side view 1. Front face of the drum 2. Limiter 3. Rubber bushing 4. Mounting plate 5. Vibration switch 6. Adjusting nut 7.
PAGE 18
Verifying the Vibration Switch Function Belt Inspection and Adjustment 1. Open the control panel cover. 1. Turn off power to washer at the circuit breaker or fuse box. 2. Start the extraction mode. 2. T he belts are accessible after the rear or side cover has been removed. Check the belts to make sure they are neither too tight or too loose. Change the belts if they are worn out or damaged. Always change a complete set of the belts for one transmission with the same type of belts being removed. 3.
PAGE 19
Tightening Moments Belt Replacement 1. Loosen the pulley bolts on the rear wall of the drum. IMPORTANT: ■■ Once every three months or every 500 working hours (whichever comes first) inspect the tightness of the bolts. 2. L oosen the adjusting screw. ■■ IMPORTANT: To avoid damage, do not use a pry bar to force the belts over the pulley grooves. 3. W hen replacing belts, replace them with a complete set. Make sure the new belts are the same type as the old ones. 4.
PAGE 20
Water and Steam Filters Lubrication WARNING Grease bearings and seals with a grease gun slowly, not faster than 5 strokes per minute. This avoids seal deformation and leakage. Do not operate the grease gun faster, even if the grease contains air gaps. Too much lubrication can cause the same damage as too little. Always make sure the grease gun is in perfect condition. Also, if you change lubricants, make sure the new one is compatible with the old one; failure to do so can lead to bearing failure.
PAGE 21
Thrust of Door Seal Method 2: Adjusting on the Side of the Door Hinge If there is a water leakage around the door, the door position may have shifted and is out of position or the door seal thrust may need adjustment. In some cases the door seal needs to be replaced. WARNING Method 1: Adjusting on the Side of the Door Handle 1. Unscrew the bolt (1) securing the door handle sleeve (2). 2.
PAGE 22
Models MFS180, MFS230, and MFS275: Spring Unit These models are to be adjusted by the manufacturer. 6 3 2 4 1 Models MFS80, MFS100, and MFS125: Adjust the spring units if a suspension part is not horizontal (without wash load and water) or after the spring unit has been replaced. 6 To adjust the spring unit, turn the nuts (2) the same number of turns simultaneously on the opposite guiding rods (3). The adjustment is correct when the gap in all four corners of the suspended part is the same (X = 2.
PAGE 23
TROUBLESHOOTING Door Will Not Unlock Possible Cause ■■ In an emergency (cont.): Models MFS80, MFS100, and MFS125: Use a screwdriver (1) or piece of wire with a maximum diameter of 0.21" (5.5 mm). Insert the screwdriver or wire through the finger hole in the lock cover (2) and push with normal pressure. The latch mechanism (3) will lift up and release the lock. The lock will stay unlocked even after the screwdriver or wire is removed.
PAGE 24
REMOVING THE WASHER FROM SERVICE Disconnecting the Washer 1. Disconnect the washer from electricity. 2. T urn off power at the main switch on the rear of the washer. 3. S hut off the water and steam to the washer. 4. D isconnect all water and steam inlets. 5. I nsulate the external electric power inlet conductors. 6. P lace an “Out of Service” sign on the washer. 7. U nscrew any nuts (bolts) that may be securing the washer to the floor. 8.
PAGE 25
DIMENSIONS AND TECHNICAL SPECIFICATIONS (Models MFS80, MFS100, and MFS125) Front View Side View Top View 1. F ront panel with operating elements 2. Electric switchboard cover 3. T ub ventilation: 2.4"/60 mm 4. Lubrication 5. Turnbuckle soap supply cable 6. Main power supply bushing 7. Main switch 8. Hard cold water inlet 9. Hot water inlet 10. Soft cold water inlet Back View 11. Hose connection external soap supply 12. Data plate 13. Steam inlet 14. External terminal 15. Drain outlet 16.
PAGE 26
Dimensions and Connections Washer Capacity A A1* B B1* C C1 D D1 E F G G1 H H1 J K L M N O P P* Q R S T U V W X Z 80 lbs (33 kg) 100 lbs (40 kg) 47.04" (1195 mm) 53.58" (1361 mm) 75.00" (1905 mm) 4.56" (116 mm) 41.54" (1055 mm) 38.58" (980 mm) 52.40" (1330 mm) 62.99" (1600 mm) 48.11" (1222 mm) 11.80" (300 mm) 1.97" (50 mm) 4.33" (110 mm) 63.66" (1617 mm) 0.98" (25 mm) 28.74" (730 mm) 61.69" (1567 mm) 16.61" (422 mm) 3.15" (80 mm) 3.15" (80 mm) 2.75" (70 mm) 70.16" (1782 mm) 65.82" (1672 mm) 2.
PAGE 27
Technical Specifications (Models MFS80, MFS100, and MFS125) MFS80 MFS100 MFS125 Washer Dimensions* Width Depth Height 47.04" (1195 mm) 52.40" (1330 mm) 75.00" (1905 mm) 47.04" (1195 mm) 56.30" (1430 mm) 75.00" (1905 mm) 47.04" (1195 mm) 63.40" (1610 mm) 75.00" (1905 mm) 56.30" (1430 mm) 58.10" (1475 mm) 82.90" (2105 mm) 156 ft3 (4.4 m3) 56.30" (1430 mm) 61.80" (1570 mm) 82.90" (2105 mm) 166 ft3 (4.70 m3) 56.30" (1430 mm) 68.90" (1750 mm) 82.90" (2105 mm) 187 ft3 (5.30 m3) 36.00" (914 mm) 20.
PAGE 28
Technical Specifications Cont. (Models MFS80, MFS100, and MFS125) MFS80 MFS100 MFS125 Washing Functions Washing High Extracting G-Factor 38 RPM 830 RPM Max. 350 38 RPM 830 RPM Max. 350 38 RPM 830 RPM Max. 350 Water Connection Water Inlet Connection Water Pressure Range Recommended Water Pressure Maximum Water Temperature BSP 1" 14.5–116 PSI/0.1–0.8 MPa/1–8 bar 43–73 PSI/0.3–0.5 MPa/3–5 bar 194°F/90°C Drain Connection Drain Valve Diameter Flow Rate 2 x 3"/76 mm 80 gal/300 dm² min.
PAGE 29
DIMENSIONS AND TECHNICAL SPECIFICATIONS (Model MFS180) 3 2 A 4 H G 5 I M L 6 F E K J D B C Front View Side View P 7 O R S Q 13 12 N BB 8 9 10 11 Y T AA Z U V W X 15 Top View 1. Operator panel 2. Data plate 3. C ompressed air supply 4. Main switch 5. Electric switchboard cover 6. Entry main power cable 7. Soap dispenser 8. Hard cold water inlet 9. Soft cold water inlet 10. Hot water inlet Back View 11. Hose (hoses) connection soap supply 12. Steam inlet 13.
PAGE 30
Dimensions and Connections Washer Capacity A B C D E F G H I J K L M N O P Q R S T U V W X Y Z AA BB 30 180 lbs (80 kg) 60.23" (1530 mm) 15.75" (400 mm) 54.72" (1390 mm) 45.27" (1150 mm) 77.55" (1970 mm) 78.58" (1996 mm) 0.39" (10 mm) 1.77" (45 mm) 53.42" (1357 mm) 26.77" (680 mm) 64.56" (1640 mm) 4.92" (125 mm) 7.28" (185 mm) 70.74" (1797 mm) 5.51" (140 mm) 4.92" (125 mm) 4.92" (125 mm) 3.93" (100 mm) 3.54" (90 mm) 2.83" (72 mm) 5.59" (142 mm) 55.11" (1400 mm) 11.81" (300 mm) 14.96" (380 mm) 1.
PAGE 31
DIMENSIONS AND TECHNICAL SPECIFICATIONS (Models MFS230 and MFS275) 1 A E D F 2 C B Side View Front View 3 G H I K L J 789 M Y N Y 4 5 6 15 14 10 U X W V O 13 12 11 PQ R S T Top View 1. Operator panel 2. Electric switchboard cover 3. S oap dispenser 4. Hard cold water inlet 5. Soft cold water inlet 6. Hot water inlet 7. Steam inlet 8. Data plate 9. Tub ventilation 10. Compressed air supply Back View 11. Entry main power cable 12. Main switch 13. Drain outlet 14.
PAGE 32
Torque Specifications Dimensions and Connections 32 Washer Capacity 230 lbs (104 kg) 275 lbs (125 kg) A B C D E F G H I J K L M N O P Q R S T U V W X Y 70.78" (1798 mm) 15.75" (400 mm) 66.45" (1688 mm) 47.24" (1200 mm) 76.61" (1946 mm) 25.59" (650 mm) 79.13" (2010 mm) 9.25" (235 mm) 4.92" (125 mm) 4.92" (125 mm) 4.64" (118 mm) 5.27" (134 mm) 3.14" (80 mm) 6.69" (170 mm) 9.6" (244 mm) 14.6" (371 mm) 15.55" (395 mm) 27.95" (710 mm) 7.48" (190 mm) 20.47" (520 mm) 3.22" (82 mm) 56.29" (1430 mm) 60.
PAGE 33
Technical Specifications (Models MFS180, MFS230, and MFS275) MFS180 MFS230 MFS275 Washer Dimensions* Width Depth Height 60.23" (1530 mm) 70.86" (1800 mm) 78.73" (2000 mm) 70.86" (1800 mm) 79.13" (2010 mm) 76.77" (1950 mm) 73.03" (1855 mm) 79.72" (2025 mm) 81.88" (2080 mm) 66.53" (1690 mm) 76.77" (1950 mm) 86.61" (2200 mm) 256 ft3 (7.25 m3) 73.42" (1865 mm) 83.66" (2125 mm) 92.33" (2345 mm) 328 ft3 (9.29 m3) 78.73" (2000 mm) 85.43" (2170 mm) 92.12" (2340 mm) 359 ft3 (10.16 m3) 43.
PAGE 34
Technical Specifications Cont. (Models MFS180, MFS230, and MFS275) MFS180 MFS230 MFS275 Washing Functions Washing High Extracting G-Factor 36 RPM 750 RPM Max. 350 35 RPM 725 RPM Max. 350 34 RPM 700 RPM Max. 350 Water Connection Water Inlet Connection Water Pressure Range Recommended Water Pressure Maximum Water Temperature BSP 1" 14.5–116 PSI/0.1–0.8 MPa/1–8 bar 43–73 PSI/0.3–0.5 MPa/3–5 bar 194°F/90°C Drain Connection Drain Valve Diameter Flow Rate 2 x 4"/103 mm 142 gal/540 dm² min.
PAGE 35
DIMENSIONS AND TECHNICAL SPECIFICATIONS (Models MFS230 and MFS275 with Tilting Feature) Dimensions and Connections Washer Capacity 230 lbs (104 kg) A B C D E F G H I J 73.22" (1860 mm) 86.41" (2195 mm) 86.41" (2195 mm) 97.55" (2478 mm) 40.11" (1019 mm) 34.01" (864 mm) 23.70" (602 mm) 20" (508 mm) 6.29" (160 mm) 27.24" (692 mm) 275 lbs (125 kg) 73.22" (1860 mm) 91.73" (2330 mm) 86.41" (2195 mm) 103.62" (2632 mm) 39.68" (1008 mm) 33.97" (863 mm) 24.64" (626 mm) 18.97" (482 mm) 5.9" (150 mm) 27.