OPERATION INSTRUCTION 4-Wire IP Video Door Phone 7 Inch Touch Screen Series User Manual Statement * If there is any doubt or disputable regarding information in this manual, you can call our company for clarification. * There maybe some difference between the description provided here and the actual devices, as our products are constantly developing and upgrading. We apologize if this manual does not contain all of the latest updates.
※ The doorbell/camera units should be fitted with an approved weather shield if the chosen position is in direct sunlight, or in contact with rain, snow or irrigation sprinkler systems. Limitation Of Liability ※ This users' manual is supplied 'as is', with no warranties, be it expressed or implied, including, but not limited to, the implied warranties of merchantability, suitability for any exact purpose, or non-infringement of any third party's rights.
1. Description Of The Indoor Monitor 1.3 Note On Wiring Connection 1.1 Fittings Indoor monitor (1pcs) The power supplies for electric lock, CCTV cameras and extension cables are not included in the package, user can purchase according to actual requirement. Screw anchors Bracket (4pcs) (1pcs) 4pin cable (5pcs) User Manual (1pcs) In the standard delivery the system supports locks with Normally Open (N.O.) door unlocking method.
1.4 Install The Indoor Unit 75-4+2*0.5mm 2 shielded coaxial wiring cable: Connect the shielded wiring cable to GND, connect the coaxial wiring cable to Video, connect the other two wiring cable to Audio and VCC; GND GND Video Video * Please be far from the devices with intense radiation: TV, DVR, etc. * Do not disassemble privately to avoid the electric shock. * Do not drop, shake or knock the device, otherwise will damage the elements. * Choose the best position to install.
1.7 Operation Introduction on Indoor Monitor 1.6 Description On Indoor Unit Visitor Call 1 2 4 5 3 Descriptions Name 1 2 3 4 5 1. Red -- Standby mode. 2. Green -- Monitoring Door 1. LED indicator 3. Yellow -- Monitoring Camera 1. 4. Blue -- Monitoring Door 2. 5. Purple pink -- Monitoring Camera 2. Standby mode The Visitor press the call button on outdoor camera 1 A continuous ring tone is heard inside and outside The visitor’s image automatically displayed on the screen. TFT display & 1.
Monitoring On Indoor Monitor Call Transfer To Other Extension Please be aware of Connection of 2 outdoor cameras and 2 CCTV cameras to 1 indoor monitor is required for dual entrance monitoring at least. Outdoor camera calls indoor monitor and conversation is underway. Standby Mode Touch the screen anywhere to access the main menu, press “ Internal communication function requires at least two indoor monitors and one outdoor doorbell to be connected.
B. This IP indoor monitor supports the directional call function, if the connected indoor extension also supports the directional call function, the user can enter the indoor extension menu “Mode” interface to set the “Mode” option, for example, set the “Mode” to “Slave 1”. Standby Mode Touch the screen anywhere to bring up the main menu. NOTICE: In internal communication mode, if a visitor press the call button on either of outdoor unit, the internal communication mode will be switched off.
System setting 2.1 Outdoor bell and Camera monitoring In standby mode, touch the screen anywhere to access the main menu, press “ ” to enter the next menu interface, option “ ” and “ ” to make outdoor bell monitoring, option “ ” and “ ” to make CCTV camera monitoring.
[Indoor unlock delay]: The unlocking time of the door lock connected to the indoor monitor can be set between 1 second and 10 seconds. Press “ < ” or “ < ” to modify. 2.2.2 Setting-Door setting Touch the option “Door setting” to enter the “Door1” menu. On Door setting menu, user can select Door1 or Door2 to set Signal mode, Signal type, unlock delay, Record mode, Motion detection, Motion detection duration, Motion display, Alarm by motion detection, Message, and Ring setting. ” to exit.
[Ring select]: When the “Ring mode” is set to “Standard”, 12 ringtones are available for setting. When the “Ring mode“ is set to “Customize”, user can select the mp3 ringtone on the TF card to set. Press “ < ” or “ < ” to modify. [Ring volume]: Press “ < ” or “ < ” to set the ring volume of the indoor monitor, which can be set from 0 to 10. [Out door volume]: Press “ < ” or “ < ” to set the volume of the outdoor bell, which can be set from Off to 10.
[Net pairing Mode]: Use this field to configure the device network. When the monitor will connect to the Wi-Fi router via a wireless network, user can select "EZ Mode" or "AP Mode" to set. When the monitor is connected to the Wi-Fi router through a network cable, uaer can select "cable" to set. Press “ < ” or “ < ” to select the net pairing mode, press “ ”, the following window will pop up, press “Ok” to confirm, the monitor will auto-reboot.
Information Information Software version Software version 0.0.0.1 0.0.0.1 Release date 2021-11-29 Release date 2021-11-29 SD remain space 7.3G/7.3G SD remain space 7.3G/7.3G UUID *8105f097 UUID *8105f097 City Zhongshan Weather Sunny O Temperature 25 C Humidity 46% Pressure 1014 mmHg 2.3 Scene mode [Call record]: All call record videos and call snapshots can be previewed on the “Call record” file.
4. Screen saver display Touch a list to play. Play back a video: Sunny Temperature:25oC Humidity:49% Pressure:1004 mmHg 20210525115515_0008_DOOR1.mov 3 7 99 00:07 00:13 0 2021-11-29 Monday [ [ [ [ [ [ [ [ ]: Touch this item to switch to the previous file. ]: Touch this item to pause, and the icon will change to “ ”. ]: Touch this item to switch to the next file. ]: Touch this item to decrease the volume. ]: Touch this item to increase the volume. ]: Play progress bar.
5. Mobile Phone Software Visit 5.4 Set up IP Indoor Monitor Home Security Begins at the Tuya Smart 5.4.1 Wired network Your new security products are start of Tuya Smart around your entire property. Now, you’ll always be connected to your home, so you can watch over your property and answer it from anywhere. 5.1 Download Tuya Smart app The Tuya Smart will walk you through setting up and managing your all security products.
Step 4. Login the Tuya Smart app, add a new IP monitor. Click “Add Device”->“Auto Scan”-> choose available device found to add. Step 2. Login the Tuya Smart app, add a new IP monitor. Click “Add Device” or “ ” Click “Add Manually”->“Video Surveillance”->“Access Control”; Wait for connection; 5.4.2 Wireless network Choose “EZ Mode”, make sure the monitor enter EZ mode; Choose 2.
5.5 The icons on live view Step 2. Login the Tuya Smart app, add a new IP monitor. Touch “Add Device” or “ ” Click “Add Manually”-> “Video Surveillance”-> “Access Control” Choose “AP Mode” Make sure the indoor monitor is already in AP mode, click “Next”; Setting Preview mode Mute Full screen preview Volume on Speak Album Switch Channel Snapshot Unlock for Door1 Choose 2.
6. Alarm Instructions CAM1 and CAM2 of this production have each an alarm function. When the trigger terminal and GND is shorted, the alarm is activate, the speaker of the indoor monitor rings and continues the duration according to the menu “Setting->Camera setting->Camera 1/Camera 2 -> Alarm time”, during this time, touch “ ” to stop alarming and enter the standby mode. For the models with SD card, simultaneously, triggers recording or snapshotting(related to the system settings).
After connecting to the Amazon Echo hotspot, return to the page. At this point, the connection is successful. Tap “Continue” to proceed to the next step. Choose a Wi-Fi network to connect to. Amazon Echo will take a few minutes to try to connect to the network. 4). After the network connection is successful, Tap “Continue”. An introduction video will appear. After the video ends, Tap “Continue” to jump to the Alexa Home page. You have now completed the Amazon Echo’s configuration. 3.