Operating Manual

ManualsBrandsMAYFLASH ManualsElectronicsPodsKit

System Compatibility

Introduction

Quick Start

Product Specification

Thank you for purchasing the MAYFLASH PodsKit

Bluetooth Audio Adapter for Nintendo Switch, PS4 and PC!

Please read this manual thoroughly before using the

PodsKit for the first time, and retain this manual for future

reference.

-Switch (handheld mode), Switch

Lite and PC (with an available USB-

C port):

Plug the PodsKit into the USB-C port

of your Switch console / PC.

-Switch (docked mode), PS4 and PC

(with an available USB-A port):

Attach the USB-C to USB-A adapter

(included) before plugging the

PodsKit in.

Bluetooth USB Audio Adapter

for Nintendo Switch, PS4 & PC

Nintendo

Switch

Nintendo Switch

Lite

Windo

PodsK

PodsKit

USB-A

adapter

USB-

2. Enter pairing mode on the PodsKit, by holding button 1 or

button 2 for 4 seconds.

1. Set your Bluetooth headphones or earphones to “pairing”

mode (please

consult the operating manual of your Bluetooth device for

instructions on how to enable pairing mode).

4. Pairing is successful when the LED on the PodsKit changes

from flashing white to constant white.

1. To connect a second pair of headphones / earphones, please repeat

steps 1-4 above.

2. If you used pairing button 1 to connect the first bluetooth device, please

use pairing button 2 to connect the second device (and vice versa). Note:

Once a device has been paired with the PodsKit, it will reconnect automati-cally

next time you turn use it.

3. To connect a second pair of headphones / earphones, please repeat

steps 1-4 above.

4. If you used pairing button 1 to connect the first bluetooth device, please

use pairing button 2 to connect the second device (and vice versa). Note:

Once a device has been paired with the PodsKit, it will reconnect automati-cally

next time you turn use it.

Microphone

Input port: USB Type C / USB A (using the included adapter). Transmission distance:

10m/33ft

Frequency range:2.402GHz - 2.480GHz

Product size: 48mm x 14mm x 5.0mm

Platforms: Nintendo Switch,Switch Lite,PS4,PC

Supported protocols: Qualcomm® aptX LL™&aptX™,SBC,A2DP,AFH,HFP,HSP

■ Low Latency transmission is available only when both the Bluetooth

adapter and headset support aptX LL™ or AptX™ technology.

■ Bluetooth headsets with AptX LL™ or AptX™ technology are

recommended for music games

■ T

o activate low delay transmission using atpX™ or aptX LL™ protocols,

the Bluetooth headset and Bluetooth transmitter must both be

equipped with aptX™ or aptX LL™ technology.

■ Due to the particularity of Bluetooth signal transmission and size

limitation, TWS earphones normally have weaker signal strength and

anti-interference ability compared with ordinary Bluetooth earphones.

■ Due to the specific wireless technology built into individual Bluetooth

headsets, users may experience temporary disconnection or sound

delays causedby electromagnetic interferences in air.When this

happens, please reduce the distance between the Bluetooth headset and

the Bluetooth transmitter, and or move to a new location.

■ Warning: Changes or modifications to this unit not expressly approved by the

party responsible for compliance could void the user’s authority to operate the

equipment.

■ NOTE: This device complies with part 15 of the FCC Rules. Operation is

subject to the following two conditions: (1) This device may not cause harmful

interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.

■ FCC Statement:This equipment has been tested and found to comply with the

limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in accordance with

the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or

more of the following measures:

—Reorient or relocate the receiving antenna.

—Increase the separation between the equipment and receiver.

—Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

—Consult the dealer or an experienced radio/TV technician for help.

■ RF exposure compliance statement:

This device has been evaluated to meet the general RF exposure requirement

3. The LED indicator will start flashing white to indicate the

PodsKit has successfully entered pairing mode.

USB-

FCC ID: 2ASVQ-NS003

You are now ready to enjoy high quality sound through

your Bluetooth headphones / earphones!

Connecting a Second Bluetooth Device

PodsKit supports connection for two pairs of Bluetooth

headphones / earphones simultaneously.