Note: While every precaution has been taken in the preparation of this manual, no responsibility for errors or omissions is assumed. Neither is any liability assumed for damages resulting from the use of information contained here in.
CONTENTS 1 IB DESCRIPTION OF FEATURES -DISPLAY PANEL FEATURES oven -TCP PANEL FEATURES SR. -SIDE AND BACK PANEL FEATURES -FRONT PANEL FEATURES M OPTION SETTING MOC 13 : Bl BATTERY PACK INSTRUCTION RECEIVE 16 : MW SPECIFICATION .. 16 Caution : Any changes or modifications in construction of this device which are not expressly approved by the pasty responsible for compliance could void the user's authority to operate the equipment.
[ _OPTION SETTING MODE Press and hold "FUN" button under the condition of Power off, and then turn on the radio. To enter each option setting mode, press "FUN button POWER AND VOLUME Function 11 1. Setting of Po war Save mode This feature allows to increase the useful life of your battery significantly. » Display of Operating Power save On/Off setting Mode. PS ofF If you press the "A of ¥" button in this setting mode, power save ON/OFF will toggle en the LCD 2.
if you press the "A or ¥” button in this setting mode, scan delay time will Increase (or decrease) 1 second per press the button and changed contents will appear on the LCD. NOTE ; In the option setting mode, A. If you hold "FUN" button and then press “4 or ¥" button, the next (or previous) setting mode will appear on the LCD. B. If you press the “monster " button, ali changed contents wilt be stored and the radio will return for normal operation, C.
[I DESCRIPTION OF FEATURES @® Display Panel Features 1. Function Mode indicates the "FUN" button has been selected. 2.0W Indicates that the "Dual Watch” feature has been activated. 3.PS Indicates that the radio is in the "Battery Save” or "Power Save” mode, 4, Lock Indicates the “Key Lock” feature has been activated 5. Beep Indicates that "Beep phone confirmation is on, 6. Memory channel indicator Display the mode channel number, 7. d2 (Dot No. 2) Not Used 8. d1 (Dot No.
11. Battery remainder level meter Not Used 12. Battery indicates batteries are getting low. If the battery level is lower than the standard point, Battery Level Indicator will twinkle. 13, BUSY indicates that RF signal received.
1. Power On/Off, Volume Turn the Volume switch clockwise to turn power on and set desired volume. Turn the Volume button counterclockwise to turn power off. 2. Squelch This control is to cut off or eliminate receiver background noise In the absence of an incoming signals. For maximum receiver sensitivity, it is desired that the control be adjusted only to the point where the receiver background on ambient background noise is eliminated.
1. MON {Monitor} Press and hold the "MON {Monitor)” button in the receiving mode to override squelch control. This is useful when weak signal is to be monitored. 2. Function (FUN) button This button, when used in conjunction with the buttons in the front panel, allows for access of each function. 3. Belt Clip Allows for easy of carrying while attached to users belt 4. DC Jack Allows for using external DC Walt Charger.
@ Front Panel Features 1. AVER Press the "AIR" button fo change the Air Band Weather Band alternate. 2. Channel Down(¥} 1) Channel Down(¥) bunion Press the button to snow to move to 2 lower Channel than is currently shown on the LCD. 2) Left Cursor function Button Frequency Selection by Cursor Function (DUNG + '¥ Button) Preferred frequency can be directly watered using cursor function in normal and memory mode. The preferred frequency however should be within allocated frequency of the receiver.
Channel Up{a) ) Channel Uptake) button Press the "A" button to arrow to move to a higher Shanna! tho is currently shown on the LCD. ) Right Cursor Button Frequency Selection by Cursor Function (FUN + & Button) The procedure for Cursor function using FUN + A key is same for FUN +¥ key. The only difference is that last 6th digit start to flash first.
With this second method the up or down key can only increment or decrement the frequency by channel step value To change the memory frequency stored within the memory faction press "FUN + MR (MW)" button whilst in memory mode. in memory mode MR icon and the memory no are displayed. The MR icon starts to blink as soon as the "FUN + MR button is pressed. This mode is called memory set mode. Now press up or down button to select the detest frequency and press MR (MW) to store it memory.
» Display of Pass message : PASS SF EEE : NOTE : The memory channels passed from scanning process is : automatically recovered when the radio is switched off and on ; again. » Display of EMPTY message | EPnpLYy go : J] spr n Men if only one channel will remain because of the passing channel! from scanning process, the process will stop and "EMPTY" message will appear on the LCD. NOTE : Other buttons located on the front of the radio will not operate.
: To turn off the “Dual Watch” Channel, simply press the "FUN + : SCOW "button. Note that the radio will return fo the “A” channel! for : normal operation. If you press the “FUN + SCOW" button when a : signal is receiving on the channel "A" or "B”, the Dual Watch feature | Witt be turn off, on the "A" or "8". : if a signal is being received at A channel, Unit will stay on channel A until the signet disappears.
[Bl BATTERY PACK INSTRUCTION 1 Press down the battery lock button on the bottom side of the radio. (D) : 2. Open the battery cover on the back side of the radio Install the battery as like & : 4. Put on the battery cover. : 5. Press the battery lock button upward to lock the battery case, | : To supply the power, use the DC charge adapter or desk top charger.
[Ml TO RECEIVE Keep the radio turned on and select the channel you want to listen to. if the Squelch is activated more than 20ms in the receiving mode, BUSY wilt appear co the LCD and speaker mute will ba removed and the audio on that channel will be heard through speaker. |W SPECIFICATION ] 1. GENERAL FREQUENCY oversensitiveness AIR BAND 1 108MH2 TO 136.
(VP may com Co., Ltd. Suite 463, APT Factory 201, Han-dong, Pyongyang-City, ; Kong K-Do, Korea. Kwangju, P.O Box 77.