MODEL: SK1204/SK1208 SK1204 SK1208
A CA LL LL DO NOT CONNECT TO COMPUTER ! USE MOBILE PHONE BATTERY IF NECESSARY (POWER BANK OR MOBILE PHONE BATTERY NOT INCLUDED) ALL CALL WARNING: WHEN NOT IN USE DISCONNECT BATTERY 1
Thanks for purchasing this MULTI-channel FM wireless intercom . This is an "INDEPENDENT" intercom system. Simply plug the intercom into standard AC outlets, and you're ready to send and receive calls or to monitor the room where the stations are installed. All the safety and operating instruction should be read before the appliance is operated and retained for future reference.
Operation Follow these steps to prepare the workstation. 1.To turn on the intercom, press and hold the power button for 3 seconds until it clicks. The channel (button) is on. Set the volume to medium 2.Set CHANNEL and CALLING for each station to the appropriate channel, as follows: * If you want all the stations to communicate with each other at the same time. set all stations to the same channel. * If you want to set up separate communica- tion systems, set each station to a different channel.
• Wipe the stations with a damp cloth occasionally to keep them looking new. Do not use harsh chemicals, cleaning solvents, or strong detergents to clean the stations. • Modifying or tampering with the stations internal components can cause a malfunction and might invalidate the intercoms warranty and void your FCC authorization to operate it. lf your intercom is not performing as it should, take it to your local store for assistance.
SK1204 FRS Frequencies: Channel Frequency (MHz) 1 CTCSS CODE CTCSS (Hz) 462.5625 A 67.0 2 462.5875 B 69.3 3 462.6125 C 165.5 4 467.5625 Troubleshooting Guide Problem Possible Solution Channel Button (Power indicator) does notlight. - Check AC power cord; Is the connection correct? - Hold down the POWER button for 3 seconds until "click" is turned on. Cannot receive response. - Is intercom set to designated channel and same CTCSS code? - Release TALK when not talking.
Problem Possible Solution Static noise or cannot communicate -All unit should be set to same CODE & same CHANNEL (refer to instruction manual Page. 4 . 6 and 8) -Change locations by using Mobile Phone Power Bank, moving to other locations for better reception and transmission.
UNNECESSARY NOISES FROM NEARBY DEVICES : (CTCSS) A/B/C Code : If your intercom system setting is at "A" code and get lot of outside unnecessary voices or noises; then, you may change your intercom system (all units) to "B" or "C" code in order to avoid unnecessary noises from nearby devices. USB ABC ABC Note : LOCK function (10 hours only) ---- For continuous talk, or room monitoring, please note following arrangement : Code A : No LOCK function.
USE MOBILE PHONE BATTERY TO POWER UP YOUR UNIT Location Troubleshooting Guide This intercom operates on radio frequency (RF) signal.The signal strength has been optimized for effective operation within ordinary residential or small industrial complex. If reception problem is found; for example, no audio signal or poor reception, user can but separated within short distance (3 or 6 feet) to check if the problem persists. The quality of RF signal is affected by interference and fading.
Limited 12 months Warranty This product is warranted by Seller against manufacturing defects in material and workmanship under normal use for twelve(12) months from the date of purchase from Seller. EXCEPT AS PROVIDED HEREIN, Seller MAKES NO EXPRESS WARRANTIES AND ANY IMPLIED WARRANTIES, INCLUDING THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO THE DURATION OF THE WRITTEN LIMITED WARRANTIES CONTAINED HEREIN.
“ ALL CALL ”function : You may call/talk or make announcement to all stations by depressing and holding the “ ALL CALL” button. The “CHANNEL LED” indicator will start to flash after the depressing and holding the “ ALL CALL” Speak in a normal tone while the “CALL” button is being depressed. Release the “CALL” button after you have done.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
SEM-PK20803OT