User's Manual

ManualsBrandsMaxon CIC ManualsElectronicsTwo Way Radio

SP-6402

Synthesized Scanning Radio

FCC RF EXPOSURE COMPLIANCE REQUIREMENTS FOR OCCUPATIONAL USE ONLY

The Federal Communications Commission (FCC), with its action in General Docket 93-62, November 7,

1997, has adopted a safety standard for human exposure to Radio Frequency (RF) electromagnetic energy

emitted by FCC regulated equipment. Topaz3 / Legacy subscribes to the same safety standard for the use

of its products. Proper operation of this radio will result in user exposure far below the Occupational Safety

and Health Act (OSHA) and Federal Communications Commission limits.

DO NOT transmit for more than 50% of total radio use time (50% duty cycle). Transmitting more than

50% of the time can cause FCC RF exposure compliance requirements to be exceeded.



This radio is NOT approved for use by the general population in an uncontrolled environment. This radio

is restricted to occupational use, work related operations only where radio operator must have the

knowledge to control the user’s exposure conditions for satisfying the higher exposure limit allowed for

occupational use.

When transmitting, hold the radio in a vertical position with its microphone 1 inches (2.5 cm) away from

your mouth.

The radio is transmitting when the red LED on the front of the radio is illuminated. You can cause the

radio to transmit by pressing the PTT bar on the radio.

These are required operating configurations for meeting FCC RF exposure compliance.Failure to observe

these restrictions mean violation.

Operating Instructions

About Your SP-6402 Radio

Maxon's SP-6402 radio feature up to 13 groups and up to 16 channel operation per group for a total

channel capacity of 208 channels of superior performance and reliability. Operation and functions for

Maxon's SP-6402 radios are described in this manual.

We urge you to thoroughly read this manual before operating the radio.

Application of some of the functions described in this manual is determined by the system you use. Your

Maxon Dealer will program your radio so that you have the greatest number of functions possible

relative to your needs.

Should you have questions regarding the operation of the radio please consult your Maxon Dealer.

Summary of content (10 pages)

PAGE 1
SP-6402 Synthesized Scanning Radio FCC RF EXPOSURE COMPLIANCE REQUIREMENTS FOR OCCUPATIONAL USE ONLY The Federal Communications Commission (FCC), with its action in General Docket 93-62, November 7, 1997, has adopted a safety standard for human exposure to Radio Frequency (RF) electromagnetic energy emitted by FCC regulated equipment. Topaz3 / Legacy subscribes to the same safety standard for the use of its products.
PAGE 2
SP-6402 Specification MODEL: MODEL CODE: EQUIPMENT TYPE: PERFORMANCE SPECIFICATIONS: SP- 6402 BAND: CHANNEL SPACINGS: RF OUTPUT POWER: MODULATION TYPE: AUDIO POWER: UHF2(440~470Mhz) 12.5KHz, 25KHz PROGRAMMBLE 5 / 1 WATT F3E 500mW ( EXT WITH 16 OHM) 1W ( INT WITH 4 OHM) 45.1MHz 455KHz 208 Channel SYNTHESIZER INTERMEDIATE FREQUENCY: CHANNELS: FREQUENCY SOURCE: POWER SUPPLY: Handportable TIA/EIA-603 Li-ION 7.5 VDC NOMINAL EXTREME +/- 10% VDC EXTREME Table of Contents Safety Information..................
PAGE 3
CTCSS/DCS/DTMF Scanning........................................ Normal Scan TX..................................................... Priority Scan TX..................................................... Priority Only TX..................................................... Receive Only Scan................................................. Scan List Edit ........................................................................ Licensing and Service Information........................................
PAGE 4
· Priority channel scan · Look back channel · CTCSS/DCS/DTMF tone signaling · Busy channel lockout · Time-out timer Scan List Edit Priority Channel Edit Description of Radio Components 1) Antenna Receptacle 2) Channel Selector Buttons 3) On/Off - Volume Control 4) Busy/TX/BT Indicator 5) Battery Latch 6) Push-To-Talk (PTT) 7) Monitor Button 8) Scan Button 9) Emergency Button 10)Microphone 11) Accessory Connector 12) Belt Clip 13)Battery 14) Battery Charge Contacts 15) LCD 16) Speaker 4
PAGE 5
Antenna Installation Fasten the antenna to the radio by turning the antenna clockwise into the receptacle on top of the radio. Installing and Removing the Battery Pack To Install: Position the guides of the battery in line with the radio battery guide rails and slide the battery into position until a click is heard. To Remove: Holding radio in one hand, push and hold battery latch button located in the upper right hand corner of the battery pack , held as if looking at the back of the unit.
PAGE 6
NOTE: Federal Communications Commission Rules and Regulations require that you monitor a channel for activity before transmitting. NOTE: The tri-color LED located on the top panel can help with channel monitoring. It will glow amber if RF activity is present; or green if the transmission has a CTCSS or DCS or DTMF tone that matches a tone programmed for receive in your radio. When this LED is not illuminated, the radio is indicating a "clear" channel.
PAGE 7
Scan Modes Scanning is a Dealer programmable feature that allows you to monitor a number of channels or channels within a Group. Your Dealer will help you define a scanning mode and your channel "scan list" . Normal Channel Scan Once the scan list has been established you can initiate scan by press and release of scan button, first button located beneath the PTT button. The top panel LED can be programmed to flash green as the radio is scanning.
PAGE 8
Scan List Edit You as a user can edit your radio’s scan list and priority scan channel at anytime form your radios original program. Your radio may have been programmed for channel only scan operation or channel Group scan operation this operation was determined by your Dealer programming. Please note, if your radio has been programmed for channel only scan you will not be able to edit your scan list. You will be able to edit your priority channel.
PAGE 9
Licensing and Service Information FCC Licensing The Federal Communications Commission requires that the operator of this radio be properly licensed under the applicable Part and/or Parts of the FCC Rules and Regulations. Consult with your Maxon Dealer, or contact the nearest FCC Field Office for information about obtaining a license. Service Do not tamper with internal adjustments. Damage to the equipment and/or improper operation may result. There are no user serviceable items inside the radio.
PAGE 10
Limited Warranty Maxon shall have no obligation to make repairs or to cause replacement required which result from normal wear and tear or necessitated in whole or in part by catastrophe, fault or negligence of the user, improper or unauthorized alterations, repairs to the Product, use of the Product in a manner for which it was not designed, or by causes external to the Product. This warranty is void if the serial number is altered, defaced or removed.