User's Manual

ManualsBrandsMaxon CIC ManualsElectronicsPrivate Land Mobile Radio for Handheld (VHF)

SP-6102

About Your S

P-6102 Radio

Maxon's S

P-6102 radio feature up to 13 groups and up to 16 channel operation per group for a total

channel capacity of 208 channels of superior performance and reliability. Operation and functions for

Maxon's S

P-6102 radios are described in this manual.

We urge you to thoroughly read this manual before operating the radio.

Application of some of the functions described in this manual is determined by the system you use. Your

Maxon Dealer will program your radio so that you have the greatest number of functions possible

relative to your needs.

Should you have questions regarding the operation of the radio please consult your Maxon Dealer.

SP-6102 Specification

MODEL: S

P- 6102

MODEL CODE: 7858

EQUIPMENT TYPE: Handportable

PERFORMANCE SPECIFICATIONS: TIA/EIA-603/ETSI300.086

BAND: VHF2(148~174Mhz)

CHANNEL SPACINGS: 12.5KHz, 25KHz PROGRAMMBLE

RF OUTPUT POWER: 5 / 1 WATT

MODULATION TYPE: F3E

AUDIO POWER: 500mW ( EXT WITH 16 OHM)

1W ( INT WITH 4 OHM)

INTERMEDIATE FREQUENCY: 45.1MHz

455KHz

CHANNELS: 208 Channel

FREQUENCY SOURCE: SYNTHESIZER

POWER SUPPLY: Li-ION(1750mA)

7.5 VDC NOMINAL EXTREME

+/- 10% VDC EXTREME

Safety Information

WARNING - DO NOT

hold the radio in such a manner that the antenna is next to, or touching, exposed

parts of the body, especially the face or eyes, while transmitting.

WARNING -DO NOT allow children to operate transmitter - equipped radio equipment.

CAUTION -DO NOT operate the radio near unshielded electrical blasting caps or in an explosive

atmosphere unless it

is a type especially designed and qualified for such use.

Summary of content (13 pages)

PAGE 1
SP-6102 About Your SP-6102 Radio Maxon's SP-6102 radio feature up to 13 groups and up to 16 channel operation per group for a total channel capacity of 208 channels of superior performance and reliability. Operation and functions for Maxon's SP-6102 radios are described in this manual. We urge you to thoroughly read this manual before operating the radio. Application of some of the functions described in this manual is determined by the system you use.
PAGE 2
CAUTION - DO NOT press and hold the transmit switch (P-T-T) when not actually wishing to transmit. NEVER use the radio in an aircraft NEVER use the radio near to sensitive medical equipment or in areas where instructed , e.g. Petrol filling stations When used in a vehicle, do not mount the radio unit on or near the Airbag or Airbag activating device. The use of an accessory not recommended or supplied by Maxon may cause damage to equipment or injury to personnel , and will invalidate warranty.
PAGE 3
4) GWR/PWR Button 5) Lamp / Lock Button 6) Battery Latch 7) Push-To-Talk (PTT) 8) Monitor Button 9) Menu/Scan Button 10)Emergency Button 11)Microphone 12) Accessory Connector 13) Belt Clip 14)Battery 15) Battery Charge Contacts 16) LCD 17) Speaker Antenna Installation Fasten the antenna to the radio by turning the antenna clockwise into the receptacle on top of the radio.
PAGE 4
To receive maximum performance from your radio and battery pack, periodically completely discharge and recharge the battery pack. Status Indicators and Audible Alert Tones Your SP-6102 has a sophisticated microprocessor control which provides a series of audible alert tones. Upon initial power up, a quick melody indicates that the self-test of the microprocessor functions has been completed satisfactorily.
PAGE 5
Menu Button you can enter the menu mode by pressing 2seconds more menu/scan button. It is possible to enable/disable or change options like below in menu mode. beep(on/off), dtmf(on/off), password(on/off), vox(on/off), squelch level(1~10), vox level(1~9), vox delay time(1~6). VOX (Voice operated transmit) This is the function that the radio can transmit by voice without pressing the PTT key. The radio can transmit with low and high voice in accordance with Vox level 1~9.
PAGE 6
This function is set when holding the Lamp.Lock button 2 seconds or more and padlock icon is displayed. Lock function is not disabled although power off and then power on again. To disable Lock function, press the Lamp/Lock button again 2secs or more. Battery Indicator It displays charging level of battery.(1~7) Upon detection of low battery condition, the radio shall emit three beeps repeatedly with display message "LOW-BATT".
PAGE 7
password Password function is the function that the user knows the password can use the radio. You can set password enable and the password code at pc program. And you can set password enable/disable by programmable key (password and menu option). Display “0000” on LCD and “↓” at currently place that you can enter the password code. At this time you can enter the password code by using Up/Dn button. To move next place, press PTT key.
PAGE 8
/ H : Tx power is high L : Tx power is Low. This icon is displayed if there is a group. Display when DTMF is set. Display when Beep is On. Display when Key_Lock option is On. Display charging level of battery. Menu / Scan Button ① Pressing the Menu/Scan Key : scan operating ② Pressing the menu/Scan Key 2 seconds or more : enter the menu mode Channel UP / DOWN ① Normal : Select a channel. ② Menu Mode : On/Off or change Option in the Menu mode. ③ Password : Channel UP/DOWN.
PAGE 9
Release squelch and tone circuit to check whether you can use or not current channel. EMG Button ① transmit DTMF ID 3 times and generate warning audio alert during 5secs. Scan Modes Scanning is a Dealer programmable feature that allows you to monitor a number of channels or channels within a Group. Your Dealer will help you define a scanning mode and your channel "scan list" . Normal Channel Scan During programming of the radio, any channel can be selected as a scanned channel.
PAGE 10
· Priority Only TX: Allows a transmission on the priority channel when scanning and not stopped on an active channel. It can also be programmed to ( Remove) will always transmit on the priority channel if scanning or stopped on an active channel. · Receive Only Scan: This allows only reception. If a transmission is made at any time, the radio will sound an alarm (two beeps) ,, display TX inhibit and will not allow the transmission.
PAGE 11
The Radio shall support the encoding and decoding of 83 normal and inverted DCS data. • TX operation : Upon the pressing of PTT, the radio shall encode the programmed DCS bit pattern for the selected channel and enter TX mode. The data shall last for the duration of the transmission. • End of TX operation : Upon leaving TX mode, the radio may employ squelch tail elimination. This shall be done by sending a turn off code.
PAGE 12
switch to the “ON” position(the yellow LED on the radio flashes). Release the monitor switch on the second led flash(In this time, the radio display “SLAVE” message on LCD). (4) Connect the cloning cable through mic jack. (5) Press the slave radio’s monitor switch. The LED shall glow green. (6) Press the master radio’s monitor switch. The LED shall glow red. And Cloning will start. (7) After cloning, the slave radio display "COMPLETED" message, and the master radio display “MASTER” message on LCD.
PAGE 13
FCC Warning Statement Any changes or modifications to the equipment not expressly approved by the party responsible for compliance could void user’s authority to operate the equipment.