MAXFOR Technology Inc. MAXFOR Technology 48, Banjeong-ro, Yangji-myeon, Cheoin-gu, Yongin-si, Gyeonggi-do, Korea Smart Gateway (MFG-G400) User’s Manual MAXFOR Technology Inc. MQEP-22-04 ( 1 / 10 ) R.
MAXFOR Technology Inc. MAXFOR Technology 48, Banjeong-ro, Yangji-myeon, Cheoin-gu, Yongin-si, Gyeonggi-do, Korea CONTENTS 1. Symbol Description and Definition ................................................................................................................ 3 2. Notice ............................................................................................................................................................................. 4 3. Introduction...............................
MAXFOR Technology Inc. MAXFOR Technology 48, Banjeong-ro, Yangji-myeon, Cheoin-gu, Yongin-si, Gyeonggi-do, Korea 1. Symbol Description and Definition WARNING Warning messages address situations that could result in injury or critical damage to the Gateway. CAUTION Caution messages address situations that could result in damage to the Gateway. NOTE Notes relate helpful information. DC Symbol Indicates the DC power. MQEP-22-04 ( 3 / 10 ) R.
MAXFOR Technology Inc. MAXFOR Technology 48, Banjeong-ro, Yangji-myeon, Cheoin-gu, Yongin-si, Gyeonggi-do, Korea 2. Notice Important matter ▷The following document is not contractually binding. MAXFOR Technology Inc. reserves the rights to revise the document at any point, following the any potential successful upgrade of the product; ▷First-time user, or whomever responsible for the repairing of the product, must read this manual thoroughly before operation.
MAXFOR Technology Inc. MAXFOR Technology 48, Banjeong-ro, Yangji-myeon, Cheoin-gu, Yongin-si, Gyeonggi-do, Korea 3. Introduction The MFG-G400 is functions as a gateway to transmit data to server without going through PC being collected data from wireless sensor network. 4. Features z Ubiquitous Sensor Network Gateway z SAMAUNG S3C6410 (ARM core) 633MHz chip. z Linux Kernel 2.6.x support. z Ethernet, Serial, JTAG, USB, GPIO Connectors. z USN to BcN Wireless interface. 5.
MAXFOR Technology Inc. MAXFOR Technology 48, Banjeong-ro, Yangji-myeon, Cheoin-gu, Yongin-si, Gyeonggi-do, Korea RF power -55dBm - 8dBm Boost mode Sensitivity -102dBm Receive sensitivity Antenna Dipole Antenna System Operation Temperature Range Humidity Range Power In Operating -20°C - 50°C Storage -20°C - 50°C 0~95% RH, non-condensing 12V DC USB Port: 5V Power Out , 500mA Alarm Port: 12V , 200mA Buzzer Port: 12V , 200mA Consumption 2.
MAXFOR Technology Inc. MAXFOR Technology 48, Banjeong-ro, Yangji-myeon, Cheoin-gu, Yongin-si, Gyeonggi-do, Korea 6. Designation NO. Description 1 LED ( Power, STATE, LINK, Tx, Rx) 2 ANTENNA(Dipole antenna) 3 Magnetic key 4 4.3 inch LCD 5 Power & Eternet Hole MQEP-22-04 ( 7 / 10 ) R.
MAXFOR Technology Inc. MAXFOR Technology 48, Banjeong-ro, Yangji-myeon, Cheoin-gu, Yongin-si, Gyeonggi-do, Korea 7. Remote access method to MFG-G400 - Remote access is used to confirm only sensor data and Set values is used to Default values. If you change the setting, remote VNC connection and data linkage can be a CAUTION problem. 7.1 Access method to VNC Viewer ① VNC Viewer Program Installation ② Run VNC Viewer and Connect Server ③ VNC connection screen MQEP-22-04 ( 8 / 10 ) R.
MAXFOR Technology Inc. MAXFOR Technology 48, Banjeong-ro, Yangji-myeon, Cheoin-gu, Yongin-si, Gyeonggi-do, Korea 8. Installation - Locate the Gateway in an area easily accessible by a technician. - Avoid locations in which the Gateway will be subjected to vibration or rapid temperature fluctuations. - Follow local regulations and site requirements. 9. Maintenance Cleaning - Use a soft cloth and mild detergent to clean the device. Do not use paint thinner, benzene, solvent or strong detergent.
MAXFOR Technology Inc. MAXFOR Technology 48, Banjeong-ro, Yangji-myeon, Cheoin-gu, Yongin-si, Gyeonggi-do, Korea FCC Part 15.105 statement This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
