User Manual M2 MID POWER 4T4R Digital Radios 37dBm Output Power 5G NR Compliant Outdoor Rated
MID POWER 37dBm Octa Band Digital Radio Copyright © Mavenir 2020. All rights reserved. This document is protected by international copyright law and may not be reprinted, reproduced, copied or utilized in whole or in part by any means including electronic, mechanical, or other means without the prior written consent of Mavenir.
MID POWER 37dBm Octa Band Digital Radio Content General ............................................................................................................................................................................. 4 Warnings .................................................................................................................................................................... 4 Site Considerations ...................................................................................
MID POWER 37dBm Octa Band Digital Radio General The M2RU components are designed for maximum safety and reliability when they are installed, used, and maintained by trained and qualified technicians in accordance with the procedures and instructions contained in this manual. To ensure the safe operation of your system, always follow the safety and operational recommendations in this manual. Warnings ⚫ M2RU is not a consumer product. Please install and use M2RU in accordance with the instructions.
MID POWER 37dBm Octa Band Digital Radio -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help. Note: Only authorized person can enter the area where the antenna is installed. And the person is fully aware of the potential for exposure and can exercise control over his or her exposure by leaving the area or by some other appropriate means.
MID POWER 37dBm Octa Band Digital Radio Warning Marks The warning marks on the equipment shell should be kept clean, readable and identifiable. ALWAYS disconnect all lines and power connections before servicing or disassembling this equipment. NEVER touch the surface after the devices power on. For performance and safety reasons, NEVER disassemble and remodel the devices.
MID POWER 37dBm Octa Band Digital Radio Preparation Unpacking and Inspection Unpack and inspect the packages as follows: 1. Open the shipping packages carefully for each unit from the protective packing sponge. 2. Ensure that all equipment and accessories have been delivered. 3. Ensure that all equipment and accessories have no damage. If there is any damage, contact your Mavenir service agent.
MID POWER 37dBm Octa Band Digital Radio Installation of the M2RU M2RU Accessories Figure 1.
MID POWER 37dBm Octa Band Digital Radio Wall Installation (Back on the Wall) 1. Attach and fasten the handle to the side of M2RU with screws M6×14 using T5 Wrench. 2. Attach and fasten the Bracket I to the back of M2RU with screws M6×14 using T5 Wrench.
MID POWER 37dBm Octa Band Digital Radio 3. Mark the position of the drilling holes in the mounting Bracket II. Note: R=13mm. 4. Drill 4 holes at the marked positions.
MID POWER 37dBm Octa Band Digital Radio 5. Attach the dowels, expansion screws or the like and fasten the Bracket II to the wall. Tips: use Bracket II as a reference to control each devices’ separation distance before hanging and locking M2RU up. 6. Hang the M2RU on the mounting bracket II and fasten with nuts M10.
MID POWER 37dBm Octa Band Digital Radio Commercial in Confidence © Copyright 2020, Mavenir 12 | P a g e
MID POWER 37dBm Octa Band Digital Radio 7. Fasten the Bracket I and II with screws M6×14. 8.
MID POWER 37dBm Octa Band Digital Radio 9.
MID POWER 37dBm Octa Band Digital Radio Wall Installation (Side on the Wall) 1. Attach and fasten the handle to the side of M2RU with screws M6×14 using T5 Wrench. Figure 2.
MID POWER 37dBm Octa Band Digital Radio 2. Attach and fasten the Bracket I to the left side of M2RU with screws M6×14 using T5 Wrench. 3. Mark the position of the drilling holes in the mounting Bracket II. Note: R=13mm.
MID POWER 37dBm Octa Band Digital Radio 4. Drill 4 holes at the marked positions. Note: H=70mm. 5. Attach the dowels, expansion screws or the like and fasten the Bracket II to the wall. Tips: use Bracket II as a reference to control each devices’ separation distance before hanging and locking M2RU up.
MID POWER 37dBm Octa Band Digital Radio 6. Hang the M2RU on the mounting bracket II and fasten with nuts M10. 7. Fasten the Bracket I and II with screws M6×14.
MID POWER 37dBm Octa Band Digital Radio Pole Installation 1. Install the handle and Bracket I to the back of M2RU. 2. Install the bracket II and Bracket III to the pole. 3. Hang the M2RU on the mounting bracket and fasten with nuts M10. 4. Connect the ground cable and power cable. Note: The diameter of Pole shall not be over 110mm or less than 55mm.
MID POWER 37dBm Octa Band Digital Radio M2RU Mounting Dimension Spacing Commercial in Confidence © Copyright 2020, Mavenir 20 | P a g e