User Manual N2 NANO POWER Octa Band Digital Radios Integrated Antennas Integrated Bluetooth
NANO POWER Digital Radio Copyright © Mavenir 2020. All rights reserved. This document is protected by international copyright law and may not be reprinted, reproduced, copied or utilized in whole or in part by any means including electronic, mechanical, or other means without the prior written consent of Mavenir.
NANO POWER Digital Radio Content General ....................................................................................................................................................................................................... 5 Warnings ............................................................................................................................................................................................ 5 Site Considerations ...............................................
NANO POWER Digital Radio Draw Circles for Plastic Expansion Nails ................................................................................................................................ 20 Assemble Mounting Bracket .................................................................................................................................................... 21 Buckle Up and Connect Wire ...........................................................................................................
NANO POWER Digital Radio General The N2 system components are designed for maximum safety and reliability when they are installed, used, and maintained by trained and qualified technicians in accordance with the procedures and instructions contained in this manual. To ensure the safe operation of your system, always follow the safety and operational recommendations in this manual. Warnings ⚫ N2 system is not a consumer product. Please install and use N2 system in accordance with the instructions.
NANO POWER Digital Radio -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help. Note: Only authorized person can enter the area where the antenna is installed.
NANO POWER Digital Radio Preparation Unpacking and Inspection Unpack and inspect the packages as follows: 1. Open the shipping packages carefully for each unit from the protective packing sponge. 2. Ensure that all equipment and accessories have been delivered. 3. Ensure that all equipment and accessories have no damage. If there is any damage, contact your Sunwave service agent.
NANO POWER Digital Radio Figure 1. N2RU Spacing to Wall The minimum spacing of 2 N2RU is 24mm. Figure 2. Minimum Spacing of 2 N2RU Note: 2 N2RU installed in one spot are directional for case installation and cooling.
NANO POWER Digital Radio Installation of the A2 Mount the A2 in the Rack A2 Accessories Figure 3. A2 Accessories Note: the ground wire of A2 is 12AWG and 2 meter in Accessories package.
NANO POWER Digital Radio Attach A2 Handle 1. Attach the 19" mounting brackets at the front of the A2, using 4 screws M3×16 per bracket and the Phillips screwdriver. Observe the orientation of the brackets. 1. Attach the sliding rails Ⓑ to the rack. Figure 4. Attaching a 19" Mounting Bracket Attach Sliding Rails and A2 to Rack Note: the sliding rails are not included in the delivery. Figure 5. Attached Sliding Rails 2. Place the A2 in the rack. Figure 6.
NANO POWER Digital Radio 3. Secure the A2 using 2 screws M6×16 on both sides and the Phillips screwdriver. Figure 7. Fix A2 with Screws For rack installation, it is highly recommended to use a fan tray in the middle of 2 adjacent A2 for cooling. Note: It will reduce service life if A2 is continuously working in environment of high temperature. Figure 8. Separation of Adjacent A2 Connect Power and Ground Cable to A2 1. Connect and lock the power cable at the rear of the A2. Figure 9.
NANO POWER Digital Radio 2. Connect and screw the ground wire at the rear of the A2. Figure 10. Connect Ground Cable at Rear Side Mount the A2 on the Wall Attach Handle to A2 Attach the 19" mounting brackets to the rear of the A2 unit, using 4 screws M3×16 per bracket and the Phillips screwdriver. Observe the orientation of the brackets shown in Figure 11. Figure 11.
NANO POWER Digital Radio Mount A2 to Wall 1. Hold the A2 to the installation location and mark the position of the 4 mounting holes in the mounting brackets. 2. Drill the mounting holes according to the chosen mounting accessories. 3. Attach the dowels, expansion screws, or the similar and fasten the A2 to the wall. Figure 12. Marking the position of mounting holes Figure 13.
NANO POWER Digital Radio Connect Power and Ground Cable to A2 1. Connect and lock the power cable at the rear of the A2. 1. Connect and screw the ground wire at the rear of the A2. Figure 14. Connect power cable at the rear of the unit Figure 15.
NANO POWER Digital Radio Installation of the N2RU N2RU Ceiling Installation (with the suspended ceiling) N2RU Accessories Figure 16.
NANO POWER Digital Radio Assemble Bracket I&II 1. Assemble Mounting Bracket I & IV with 6 x M3 x 6 screws. 2. Attach Nylon Cable Tie to the Bracket I & IV combination 1. Drill a hole with a diameter of 90mm for putting Mounting Bracket I & IV. Figure 17. Assembling Bracket I & IV Figure 18. Attaching Cable Tie to Mounting Bracket Place the Bracket Figure 19.
NANO POWER Digital Radio 2. Place the Mounting Bracket I & IV on to which the N2RU will be attached to the reverse of the Ceiling Tiles. 3. Ensure the nylon tie hangs down through the hole. 1. Attach Mounting Bracket II to Mounting Bracket I using 2 x M6 x 70 screws, Flat Washer M6, and Spring Washer M6. Figure 20. Placing Bracket I & IV Figure 21. Placing Bracket 2 Assemble Bracket II Note: Paired Mounting Bracket III is already assembled into N2RU in factory Figure 22.
NANO POWER Digital Radio Buckle Up and Connect Wire 1. Clip the bar on paired Bracket III over the hooks on Bracket II. 2. Connect the power cable and fiber cable to N2RU Figure 23. Connecting Bar over Hooks on Bracket II Note: Connect power cable first and then power it on. Do NOT connect the powered cable to the N2RU in case of excessive current impulse. Figure 24. Wire Connection Diagram 3.
NANO POWER Digital Radio Figure 25. Installation Completed Diagram 4. Tighten the M3 x 3 screws 1. Depress the hook on the front of the N2RU to expose top panel of N2RU for debugging and maintenance Figure 26. Tighten N2RU To Perform Maintenance on the N2RU Figure 27.
NANO POWER Digital Radio Figure 28. Unlock Rotary Hook Diagram 2 N2RU Ceiling Installation (without suspended ceiling) Draw Circles for Plastic Expansion Nails 1. Using the Mounting Bracket III keyholes as guides, mark the position of the 2 holes to be drilled into the ceiling. Figure 29.
NANO POWER Digital Radio 2. Drill 2 holes with a diameter of 10mm and depth of 55mm at the positions in step 1 3. Insert plastic wall plugs into holes by hammer 1. Assemble Mounting Bracket III to the ceiling using ST6.3 X 50 screws. Figure 30. Drilling Holes Diagram 1 Figure 31. Insert Plastic Wall Plugs Assemble Mounting Bracket Figure 32.
NANO POWER Digital Radio Figure 33. Assembling Bracket III Diagram 2 Buckle Up and Connect Wire 1. Clip the bar on paired Bracket III over the hooks on Bracket II. 2. Connect the power cable and fiber cable to N2RU Figure 34. Connecting Bar over Hooks on Bracket II Note: Connect power cable first and then power it on. Do NOT connect the powered cable to the N2RU in case of excessive current impulse.
NANO POWER Digital Radio Figure 35. Wire Connection Diagram 3. Engage the rotary hook on Bracket IV into Bracket II 4. Tighten the M3 x 3 screws Figure 36. Installation Completed Diagram Figure 37.
NANO POWER Digital Radio 1. Depress the hook on the front of the N2RU to expose the top panel of N2RU for debugging and maintenance. Figure 38. Unlock Rotary Hook Diagram 1 Figure 39.