Specifications: Active Loudspeaker Specifications Powered Wireless loudspeaker system Texas Instruments DSP & Class D amplification Wireless Solution – STS technology (SMSC) Rear firing reflex port WS10i HF unit (x2) 2” full range driver, paper cone with titanium dust-cap. High efficiency, low distortion NdFEB Motor 12W@THD 1% for each channel.
What's in the box? 1 x Active loudspeaker 1 x Power cords/Power Supply 1 x Desk Stand 1 x Remote control 1 x Line out cable- (RCA – mini jack) 1 x 3.5mm Mini Jack cable (3.5mm mini jack – 3.5mm mini jack) The loudspeaker is covered with a soft faux leather material. Please take care when unpacking the loudspeaker to avoid scratching or indenting the material. Before installing this product please read all of the instructions.
Getting Started Place the speaker in your preferred position but within reach of a wall socket. With the mains socket in the OFF position, connect the a/c lead to the speaker using only the supplied mains leads and power supply. Turn the mains socket ON. Your WS10i has been supplied with two cables to enable connection to your source devices. Devices with 3.5mm headphone out socket (e.g. Mp3 player) 3.5 3.5 cable Connect one end of the 3.5mm to 3.
When using optional transmitter (WST) Wireless Mode When the transmitter is connected to a source device the LED will flash intermittently When the speaker is connected to mains power the LED on the front of the speaker will light up for 3 seconds then power off. Using the remote control, aim at the speaker and press the Power On button.
To use your speakers with a PC or MAC MAC set-up 1.Insert the USB connector from the transmitter to a free USB socket on your MAC. 2.Go to System Preferences and under Hardware choose Sound. 3.Click Output in Menu and choose USB headset. PC set-up 1.Insert the USB connector from the transmitter to a free USB socket on your PC or laptop. 2.Wait until the software has been installed, usually a confirmation beep or message window alert. If the above instructions do not work you may need to do the following.
Remote control Power on/off Mute Station VOL+ VOL- Page | 6 201205-WS10i說明書NEW.
Rear Panel WS10i STATION CBA R Stereo L ZONE Channel LINE IN DC IN Line In Right - Stereo - Left Switch Set to Stereo when one WS10 i is used. Multi-Zone Switch Power STATION Change station by pressing this button Page | 7 201205-WS10i說明書NEW.
To use your speakers with MP3 devices (headphone out) Plug one end of the supplied 3.5mm mini jack lead into the transmitter and the other end into the headphone socket on your device. Plug the USB connector from the transmitter into the mains adapter and plug the mains adapter into a convenient wall socket and turn on. Push the button in the centre of the transmitter to select a free zone. Using the remote control press the “station” button” to find the signal from the new source equipment. ….
Complete home wireless network set up. Take it seriously easy. Page | 9 201205-WS10i說明書NEW.
Wireless link TV Line out cable- (RCA – mini jack) Computer USB Cd、MP3、Mobilephone... 3.5mm Mini Jack cable Select the LED colour WS30 Subwoofer Amplifier Speaker WS80 WS10 or Select same colour Page | 10 201205-WS10i說明書NEW.
Optional Extra’s WS10 i Active loudspeakers - add more speakers to complete your multi room requirements WSt Transmitter - more transmitters, more devices can be used! Wireless dongle For more information please visit www.blueaura.co.uk or contact info@blueaura.co.uk Page | 11 201205-WS10i說明書NEW.
Product Registration (address on back cover) Model Serial Number Date of purchase Customer details Name Address line 1 Address line 2 Town Country Postcode/zip code Telephone Dealer details Dealer name Address line 1 Address line 2 Town County Postcode Country Page | 12 201205-WS10i說明書NEW.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER. NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
IMPORTANT SAFETY INSTRUCTIONS 01. 02. 03. 04. 05. 06. 07. Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use apparatus near water. Clean only with a dry cloth. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 08. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 09.
IMPORTANT SAFETY INSTRUCTIONS 13. Damage Requiring Service D If the apparatus does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the apparatus to its normal operation. E. If the apparatus has been dropped or damaged in any way, and. F.
FCC Compliance This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help.
FCC RF Exposure Requirements (MPE) To satisfy FCC RF exposure requirements, a separation distance of 20 cm or more should be maintained between the antenna of this device and persons during device operation. To ensure compliance, operations at closer than this distance is not recommended. Les antennes installées doivent être situées de facon à ce que l a popul ation ne puisse y être exposée à une distance de moin de 20 cm.
and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. Conformément à l a réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour l'émet teur par Industrie Canada.
Blue Aura Worldwide Guarantee This entitles you to have the unit repaired free of charge, during the first two years after purchase, at any authorised Blue Aura distributor provided that it was originally purchased from an authorised Blue Aura dealer or distributor.