User's Manual

ManualsBrandsMASTER ManualsElectronicsRemote control transmitter

Dear Customer, thank you for purchasing a MASTER

S.p.A. product. This guide contains all the information you

will need concerning the use of this product. Read the

instructions carefully and keep them for further

consultation. ARCO is designed to be coupled with

MASTER S.p.A. receivers. All other use beyond the field

defined by MASTER S.p.A. is forbidden. This, as well as

the breach of the instructions given in this guide, shall

release MASTER S.p.A. from any liability and shall annul

the product warranty. Water, humidity, heat sources,

accidental falls can damage the device. Do not use

abrasive products or solvents to clean the product.

Do not use radio systems in places with strong interference (for example, near police stations, airports, banks, hospitals). It is in any case

advisable to carry out a technical inspection prior to installing any radio system in order to identify possible sources of interference.Radio systems

can be used where any disturbances or malfunction of the transmitter or receiver do not constitute a risk factor, or if such factor is eliminated using

appropriate safety systems.The presence of radio devices working at the same transmission frequency (433.42 MHz) may interfere with the

radio receiver and reduce the range of the system, limiting functionality.

433,42 MHz

rev04_12.04.19

ARCO5 - ARCO10 - ARCO20

Package contents

- 1 transmitter

- 1 CR2032 lithium battery

- 1 wall bracket

- 2 dowels

- this manual

Technical specifications

- Power supply: n° 1 CR2032 lithium battery

- Operating temperature: 0° C / +55°C

- Operating frequency: 433.42 Mhz

- Operating frequency band: 433,050 – 434,790 Mhz

- Max radiated power, e.r.p. : <10 mW

- N° of channel ARCO: 1

- N° of channels ARCO2: 2 + sequencer channel

- N° of channels ARCO5: 5 + sequencer channel

- N° of channels ARCO10: 10 + sequencer channel

- N° of channels ARCO20: 20 + 4 groups

Notes on radio system

Battery insertion /replacement

The transmitter is powered by a battery C R2032. To insert the battery,

remove the battery cover on the back of the transmitter, insert the battery

respecting the polarity, close the cover.

It it recommended to replace

the battery every 2 years.

Use of batteries different than

those referred can cause an explosion hazard. Used batteries must

be discarded in appropriate containers.

Fixing the wall bracket

A) Fix the bracket to the wall using the supplied plugs (distance between holes 36 mm).

B) Cover the screw heads with the coverage provided.

C) Hang the transmitter to the support.

1. ASSOCIATED FUNCTIONS AT BUTTONS

Basic functions

stop

down

channel - / prev

SUN On/Off

FOR ME

right orientation

To memorize:

To recall:

access to the

receiver menu

transmitters

insertion-deletion

PROG

Favorite position

Sun / Automatic lowering function

NOTE: Sun/Automatic lowering» bothIn ARCO2 the « function is active for channels: if you enable it for channel 1, it is

automatically activated for channel 2 and viceversa It is possible that some receiving devices do not associate any

operations to some transmitter buttons or that associate to the transmitter buttons some operations different from what it is

described. In this case consider the instruction manual of the receiving device.

By the «SUN On / Off " button you can activate / deactivate the SUN function or theAUTOMATIC LOWERING function, in the

receivers equipped with these functions. To modify the setting:

C) YELLOW LED IS ON activeIf : sun/automatic lowering function

B) Press until the state of the yellow LED varies (about 2seconds)

A) Select the channel (excluded sequencer channel and groups)

All products and technical specifications given in this document are

subject to variation without notice. Unless previously and

specifically authorised by the manufacturer, the device must be

used exclusively with receivers produced by the same

manufacturer. The manufacturer shall not be liable for damage

resulting from improper, incorrect or unreasonable use.

Press and then and hold

the buttons until the motor signalation (about 5 seconds)

STOP FOR ME

This transmitter complies with FCC (Federal

Communications Commission) Part 15.

Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received,

including interference that may cause undesired operatio.

Changes or modification not expressly approved by the

party responsible for compliance could void the user's

authority to operate the equipment.

2ASK4ARCOFCC ID:

User manual :

ARCO / ARCO 2 / ARCO

5 ARCO 10 / ARCO 20

MASTER S.p.A.

via S.Pertini 3, 30030 Martellago (VE)

www.mastermotion.eu

channel + / next

left orientation

MENU PROG

YELLOW Led

At the end of the product life cycle, dispose of the device

in compliance with local regulations. This product could

contain substances that are harmful to human health and

the environment: do not dispose of

the product in

domestic waste.

Disposal

Advanced functions

Pulsante MENU

Pulsante PROG

: permette di accedere velocemente alla configurazione dei parametri del ricevitore. Fare riferimento al manuale d’uso del ricevitore per le procedure.

: permette l’inserimento/cancellazione del telecomando nella memoria del ricevitore. Se il telecomando è già memorizzato, permette la memorizzazione di ulteriori

telecomandi. Fare riferimento al manuale d’uso del ricevitore per le procedure.

2. ENABLING/DISABLING GROUPS AND CHANNELS

3. DELAY OF TRANSMISSION ON GROUPS AND SEQUENCER CHANNEL

ARCO 2, ARCO 5 and ARCO 10 Sequencer

Sequencer SE ARCO 20 Groups G1 G2 G3 G4

transmitters have a virtual channel called , which sends the selected command in succession for all active radio channels. To select the

, scroll the list of channels until symbol appears. The transmitter is equipped with 4 virtual channels (called , indicated with ,,,)which send the

selected command in succession for all the active radio channels belonging to the group. To select a group, scroll the list of channels until the symbols G1, G2, G3 and G4 appear.

It is possible to set the interval (from 1 to 10 sec) of time which must pass between the transmission on one channel and the next. The factory sets the delay at 1 second. The use of high

intervals of time can negatively effect on the battery life.

To modify the setting:

4. SETTING THE CHANNELS BELONGING TO A GROUP (only ARCO20)

The transmitter is equipped with 4 virtual channels (Groups, indicated by ,,,)which send the selected command in succession for all the active radio channels

belonging to the group. It is possible to associate up to 20 channels to each group.

To set different groups, follow the procedure:

ARCO 20 G1 G2 G3 G4

A) Press and hold the buttons for about 3 seconds, until the symbol is displayed.

Press . will appear.

Press to modify the setting.

If necessary,press PREV and NEXT to select another channel/group and return to point C.

To exit, or wait about 15 seconds (the display switches off).

STOP and then MENU ch

B) STOP 01

STOP

F) press twice MENU

If : / If :YELLOW LED IS ON channel/group enabled RED LED IS ON channel/group enabled

Press and hold the buttons for about 3 seconds, until the symbol is displayed.

Press . The symbol appears on the display.

Press . The currently set value appears on the display (from 01 to 10 sec).

Use and to set the required value.

Press to save the setting.

To exit, or wait about 15 seconds (the display switches off).

STOP and then MENU ch

B) NEXT Sd

C) STOP

PREV NEXT

E) STOP

F) press 1 time MENU

A) Press and hold the buttons for about 3 seconds, until the symbol is displayed.

Press twice NEXT. symbol appears on the display. To select another group press NEXT.

Press STOP. Channel 01 appears.

Press to modify the setting.

If necessary, press PREV and NEXT to select another channel and return to point E.

To exit, or wait about 15 seconds (the display switches off).

STOP and then MENU ch

B) G1

E) STOP

G) press twice MENU

D) YELLOW LED IS ON: channel belongs to the group RED LED IS ON channel not belongs to the groupIf / If :

With transmitters ARCO 5, ARCO 10 and ARCO 20 you can turn off the channels that are not used; this will facilitate the use of the transmitter because when you scroll through the list of

channels, you find only those actually used. It's possible, with the same procedure, reactivate the channels.

The procedure is as follows:

YELLOW LedRED Led