Quick Start Guide Model: D1000 PLEASE READ THESE INSTRUCTIONS CAREFULLY BEFORE USING THIS PRODUCT AND KEEP THIS MANUAL FOR FUTURE REFERENCE.
Kit Content JSW Smart Lock Keypad JSW Smart Lock Template Screwdriver Mounting Plate Rubber Screw Pack Door Sensor Mounting Plate Screw for Mounting Plate M4 *20mm *3 for 35~40mm door thickness M4 *30mm *3 for 40~50mm door thickness M4 *40mm *3 for 50~60mm door thickness Tail Piece Standoff Spacer AA Alkaline Battery *4 35mm *1 Standoff Spacer 25mm *2 Deadbolt Pack Screw for Smart Lock *1 (M4 *17mm) Strike Plate Set Screw for Battery Cover *2 Deadbolt *1 Screw *4 (Strike Plate & Deadbolt) (M
2 Specification Unlock Button Number Keypad * Press it after unlock password input. Lock/Return Button * Lock the door. * Restart the password if input error. Battery Cover Thumbturn USB Port Internal Lock Button Reset/Bluetooth Switch Reset: Long press 5 seconds for returning to factory default setting. Bluetooth Power: Short press 1 second for turn on or off the bluetooth.
Smart Lock Model Name D1000 Unlock Options Password/BT5.0(BLE) Battery Life 10 Unlocks/Day for 1 year Power Supply AA Alkaline Battery *4 Emergency Supply USB 5 V+/- 0.2V Low Power Alarm 4.8V +/- 0.
3 Preparation Handle under the deadbolt 1 Handle above the deadbolt Door Thickness Check Points 1. The distance between door handle and deadbolt. 35mm ~60mm >170mm >50mm 2. The door thickness. 2 Door thickness & Tail piece length Please adjust the length of tail piece based on the door thickness.
4 Remove the current lock Skip this step if using original deadbolt. 60mm 5 default Adjust the deadbolt length Please measure the distance from the center of the drilled hole to the door frame. 1. 60 mm 2.
4 Installation Step 1: Install the deadbolt (Skip this step if using original deadbolt) 1 Adjust the bolt length and make sure the “+” hole of deadbolt in the middle of the door hole. 2 Twist the”+”and ensure the plate line up the bolt. 3 Deadbolt must be in retracted position.
Fixing Hole Step 2: Drill the fixing hole on the door (optional) Positioning the template to the deadbolt hole and drill a fixing hole. Step 3: Install the keypad on the outside of the door 1 Screw the standoff spacer into the keypad. 2 Run the cables through the hole BELOW the deadbolt. 3 Turn the “+”hole and ensure the deadbolt extend-retract smoothly.
2 3 UP UP Step 4: Install the mounting plate 1 Run the cable through the rectangle hole on the right. 2 Screw: Mounting plate screw *3. 3 Turn the “+”hole and ensure the deadbolt extend-retract smoothly.
Step 5: Install the door sensor 1 Ensure the sensor is close to the frame. 1 Tape the sensor on the door. 2 Fasten the sensor onto the mounting plate. 1 2 Step 6: Fit in the mounting plate rubber 1 The door senor cable goes through the hole in the middle. 2 The keypad cable goes through the rectangle hole on the right.
Step 7: Insert the cable connector onto the smart lock Black Step 8: Insert the tail piece 1 Ensure the thumbturn is in vertical position. 2 The deadbolt must be in retracted position.
Step 9: Mount the smart lock onto the door Please screw the Smart Lock in the following order: 1 Screw the Smart Lock. 2 Screw the batttery cover. 1 Screw(smart lock) *1 2 Screw(battery cover) *2 Step 10: Test the smart lock Inside Step 11: Insert the batteries and put the battery cover back on.
5 APP Guide Please download and install the “J-LOCK” APP to your smartphone. Search the app in the App Store or Google Play Store.
FCC WARNING Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Canada Statement This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device.
