20 Volt Right Angle Drill 241-0436 OPERATOR’S MANUAL CAUTION: To Reduce The Risk Of Injury, User Must Read And Understand The Operator’s Manual. Save These Instructions For Future Reference. For questions / comments, technical assistance or repair parts – Please Call Toll Free: 1-866-917-4374. (M-F 8am – 6pm EST.
table of contents Safety Symbols. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 2 Safety Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 3 Overview / Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 7 Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
safety symbols Some of these following symbols may be used on this tool. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the tool better and more safely.
safety INSTRUCTIONS The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols and the explanations with them deserve your careful attention and understanding. The symbol warnings do not, by themselves, eliminate any danger. The instructions and warnings they give are no substitutes for proper accident prevention measures.
safety INSTRUCTIONS WARNING: Read all safety warnings and instructions.Failure to follow the warnings and instructions may result in electric shock, fire and / or serious injury. Save all warnings and instructions for future reference. The term power tool in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool. WARNING: Risk of fire and electric shock. Dry location use only. Do not expose to rain. Risk of injury. Work area safety 1.
safety INSTRUCTIONS 4. Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury. 5. Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations. 6. Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing and gloves away from moving parts.
safety INSTRUCTIONS Service 1. Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained. SPECIFIC SAFETY RULES FOR CORDLESS DRILL/DRIVER 1. Use the tool only with the batteries and charger listed below: . Battery pack 252-8024 252-8028 252-8029 252-8030 252-8031 252-8032 252-8033 252-8034 Charger 252-8036 252-8037 252-8044 2.
OVERVIEW Keyless chuck LED Worklight Vents Direction of Rotation Selector (Forward/Center Lock/ Reverse) Variable speed trigger Switch Bit storage SPECIFICATIONS PRODUCT SPECIFICATIONS Switch VSR (Variable Speed Reversible) No Load Speed 0-1050 RPM Chuck 3/8” single sleeve Max.torque 150 in. lbs. Drill Weight (without battery) 2 lbs. 7 oz.
ASSEMBLY VARIABLE SPEED The variable-speed trigger switch delivers higher speed with increased pressure and lower speed with decreased trigger pressure. KEYLESS CHUCK The keyless chuck allows you to hand-tighten or release the drill bit in the chuck jaws. FORWARD/CENTER LOCK/REVERSE The direction-of-rotation selector located above the trigger switch changes the direction of bit rotation.
OPERATION TO ATTACH BATTERY PACK (Fig. 1) FIG. 1 CAUTION: when placing battery pack on the tool, be sure that the raised rib on battery pack aligns with the groove on the saw and the latches snap into place properly. Improper assembly of the battery pack can cause damage to internal components. TRIGGER SWITCH (Fig. 2a) FIG. 2a 1. L ock the trigger switch on the drill by placing the direction of rotation (forward/ center lock/reverse) selector in center (OFF) position. 2.
OPERATION DIRECTION-OF-ROTATION SELECTOR (FORWARD/CENTER LOCK/REVERSE) (Fig. 2b) KEYLESS CHUCK (Fig. 3) FIG. 3 UNLOCK (Release) FIG. 2b LOCK (Tighten) REVERSE FORWARD The direction of rotation is reversible and is controlled by a selector located above the switch trigger. With the drill held in normal operating position, the direction of rotation selector should be positioned to the left of the switch trigger for drilling.
OPERATION The LED worklight, located on the front of the Drill, will illuminate when the trigger switch is depressed. This provides additional light on the surface of the workpiece for operation in lower-light areas. The LED worklight will turn off when the trigger switch is released. INSTALLING BITS (Fig.5) FIG. 5 UNLOCK (Release) Drill bits Chuck jaws LOCK (Tighten) 1. L ock the switch trigger by placing the direction of rotation selector in center (OFF) position. 2.
OPERATION DRILLING (Fig. 7) FIG. 7 Move the drill bit into the workpiece applying only enough pressure to keep the bit cutting. Do not force or apply side pressure to elongate a hole. WARNING: Be prepared for binding at bit breakthrough. When these situations occur, drill has a tendency to grab and kick opposite to the direction of rotation and could cause loss of control when breaking through material. If not prepared, this loss of control can result in possible serious injury.
CHUCK REMOVAL (Fig. 8 & 9) FIG. 8 Mallet Chuck jaws Hex key FIG. 9 Mallet Chuck jaws Hex key To remove the chuck: 1. Lock the switch trigger by placing the direction of rotation selector in the center (OFF) position. 2. I nsert a 5/16 in. hex key into the chuck of the drill and tighten the chuck jaws securely. 3. Tap the hex key sharply with a mallet in a clockwise direction. This will loosen the screw in the chuck for easy removal. Open the chuck jaws and remove the hex key.
20 Volt Right Angle Drill WARRANTY 90-DAY MONEY BACK GUARANTEE: This MASTERFORCE® brand power tool carries our 90-DAY Money Back Guarantee. If you are not completely satisfied with your MASTERFORCE® brand power tool for any reason within ninety (90) days from the date of purchase, return the tool with your original receipt to any MENARDS® retail store, and we will provide you a refund – no questions asked.
© 2013 Menard, Inc.