USER’S MANUAL WIRELESS MICROPHONE SYSTEM TALK
WIRELESS INTRODUCTION Introduction Thank you for purchasing our product. This PLL synthesized wireless microphone system operates in UHF band frequency with 700 selectable channels. Please read this instruction manual carefully before operating the system. This manual covers the function and operation of the wireless microphone system. FCC Statement This device complies with part 15 of the FCC rules.
Quick Start Guide 1. Connected Receiver Power Cable AUDIO OUT SQ DC ONLY 12V 500mA LINE MIC AC/DC ADAPTER UNBALANCED BALANCED 2. Connect Mixer or Amplifier AUDIO OUT ANT B UNBALANCED DC ONLY SQ 12V 500mA ANT B ANT A AUDIO OUT UNBALANCED LINE MIC DC ONLY SQ 12V 500mA ANT A LINE MIC BALANCED BALANCED 3.
4. Insert Batteries 12 11 1 10 2 9 3 8 4 7 Power Sync -20 -10 5 6 Sync Power 0 -20 1.5V AA 1.5V AA 1.5V AA 11 12 10 1.5V AA 1.5V AA Step 2 Hold Sync Power Sync -20 10 0 Hold 1.5V AA 1.5V AA TALK OR TALK Step 1 3 1 3 8 5. SYNC < 1M 1.
WIRELESS PRODUCT DESCRIPTION Receiver Front : 1 2 3 4 5 6 1. Power Button. 2. LCD Display: Display channel, frequency and settings. 3. Button ▲▼: Tap the channel forward / backward. 4. SYNC Button: Press the button to actuate the synchronization with transmitter. 5. SET Button: Press button to active the manual or auto-scan or preset mode. 6. Volume Controller: Adjust the receiver output level. LCD Display : 1 3 5 6 2 4 7 8 9 10 11 1.
WIRELESS PRODUCT DESCRIPTION Rear : AUDIO OUT DC ONLY 12V 500mA ANT A 2 3 4 5 6 1 ANT B UNBALANCED SQ LINE MIC BALANCED 1 1. Antenna 2. Balanced XLR Audio Output 3. Unbalanced 6.35mm Audio Output 4. Mic/Line Switch: Use this to adjust audio output level for mic level (-20dB) or line level (0dB). 5. Squelch: Turn the knob to adjust or decrease the noise floor level. 6.
WIRELESS PRODUCT DESCRIPTION Handheld Microphone 1.5V AA 1.5V AA 6 TALK 1 7 5 4 3 2 1. Power Button: Press for 2 seconds to power the microphone on or off. 2. Power LED: Indicate the power / low battery level status. LED Indicator Status Green Ready Flashing Green The synchronization process is actuated. Flashing Red Low battery power when less than 10 minutes operation 3. Talk Button: Push the button up to talk. Push the button down for mute. 4.
WIRELESS PRODUCT DESCRIPTION Bodypack Transmitter 4 2 8 6 3 1 5 1. 2. 3. 4. 5. 6. 7. 8. 9. Power -20 Sync -10 0 9 1.5V AA 1.5V AA 7 Power Button: Press for 2 seconds to power the microphone on or off. Mute Button: With the transmitter on, a slight press for button will toggle between mute and unmute function. Power LED: Indicate the power / low battery level status LED Indicator Status Green Ready Flashing Green The synchronization process is actuated.
WIRELESS SYSTEM OPERATION Connecting the receiver Prior to setting up, please check that the transmitter and receiver are tuned to the same frequency or channel. Two or more transmitters operating in the same frequency can not be used at the same time and area. 1 Connected the provided DC power supply to the receiver power input with an appropriate AC power source. The LCD display will light and the receiver is on.
WIRELESS SYSTEM OPERATION Setting up channel on receiver Manual Mode Setting interference-free channel by manual operation. Using the △ button to select the “MANUAL” mode. Press “SET” button for 2 seconds till LCD display is flashing. Press button △ to change the channel forward. Press the “SET” button to lock the setting.
WIRELESS SYSTEM OPERATION Auto-Scan Mode Set interference-free channel by automatic frequency scan function. Using the △ button to select the “SCAN” mode. Press “SET” button for 2 seconds till LCD display is flashing. Press button △ to scan in forward direction, and it will stop at the free-interference channel automatically. Press the “SET” button to lock the setting.
SYSTEM OPERATION WIRELESS Preset Mode Set multiple constructions by using preset channels. There are 4 preset groups. Excluding the interference from external, there are 8 preprogrammed channels can be operated simultaneously in each group. Using the △ button to select the “PRESET” mode. Press “SET” button for 2 seconds till LCD display is flashing. Press channel button △ to change the programmable group forward. Press the “SET” button to lock the group setting.
WIRELESS SYSTEM OPERATION Set up the handheld microphone / bodypack transmitter Open the battery cover and insert batteries into the battery compartment conforming to the polarity (+)(-) marks. Power Sync -20 -10 0 1.5V AA 1.5V AA Unscrew the handheld Mic and open the battery cover to insert the battery into the battery compartment and confirm the marks of the polarity (+) (-). Connect to the lavalier microphone, headset microphone or guitar cable.
WIRELESS SYSTEM OPERATION 12 11 11 1 10 2 9 1.5V AA 1.5V AA 6 5 Sync Power 1 2 9 4 7 12 10 3 8 -20 -10 0 Press for 4 seconds to turn the Handheld/ Bodypack transmitter on. 3 8 4 7 6 5 If the LED stays flashing , it indicates that the battery will out of power soon and should be changed. 1.5V AA Bodypack Handheld 1.5V AA Sync Power Power Sync -20 1.5V AA 1.5V AA -10 -20 -10 Adjust the audio input level. • 0dB (Default Setting) • -10dB • -20dB 0 0 1.5V AA • 0dB 1.
WIRELESS SYSTEM OPERATION Synchronizing a transmitter with a receiver Automatic frequency synchronization via remote channel for easy setup. First, switch the transmitter and the receiver on. Press and hold the SYNC button on your transmitter. The SYNC flashes on the receiver display panel. Press the SYNC button on the receiver front panel, the transmitter will set the same channel as receiver automatically. When using SYNC setting, the distance of receiver and transmitter is within 1 M.
COLOR LABEL IDENTIFICATION WIRELESS Color Label Identification TA LK You can also stick the color label on the receiver and transmitter for quickly identify the pair system.
WIRELESS BASIC CONNECTIONS Basic Connections To combine two receivers in a 19” standard rack by using 2 short L type metal racks and 2 metal connecting plates. L4 To mount a receiver in a 19” standard rack by using 2 long L type metal racks. (L type long metal racks is an optional product, so please purchase extra in local shops.) L3 By using the antenna holder to install the UHF antenna in high place for better reception quality.
TROUBLE SHOOTING WIRELESS Trouble Shooting whether is set too high or too low.
WIRELESS SPECIFICATION System Performance Receiver Frequency Range Case Oscillator Modulation S/N Ratio Image & Spurious Rejection Receiving Sensitivity AF Response T.H.D. IF Frequency Dynamic Range Tone Signal Audio Output Power Supply Current Consumption Dimension(MM) WxHxD Weight : : Half 19” EIA Rack Metal Case : PLL Synthesized : FM : >100dB, at 20KHz deviation and 60dBµV antenna input : 70dB minimum : At 2µV over 52dB S/N ratio : 80Hz to 18KHz : <1% (at 1KHz) : 1st: 243.95MHz 2nd: 10.