USER’S MANUAL BAND DIVERSITY WIRELESS MICROPHONE SYSTEM
WIRELESS MICROPHONE SYSTEM Table of Contents 1. Introduction … … … … … … … … … … … … … … … … .… … … .… … … .… … 1 2. Safety … … … … … … … … … … … … … … … … … … … … … … … … … … … … 1 3. Environment … … … … … … … … … … … … … … … … … … … … … … … … ... 1 4. Wireless Note… … … … … … … … … … … … … … … … … .… … … … … ... 1 5. Product Description … … … … … … … … … … … … ..… … … … .… … … ..… 2 5.1 Receivers 5.2 Handheld Microphone 5.3 Bodypack Transmitter 6. Basic Connections… … … … … … .… … … … … … … ..
WIRELESS WIRELESS NOTE FCC Statement This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference and (2) This device must accept any interference received, including interference that may cause undesired operation Notice : The changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
WIRELESS PRODUCT DESCRIPTION 5. Product Description 5.1 Receivers This is a stationary diversity receiver for use with our 16- or 64-channel selectable transmitters. The receiver operates in UHF band frequency with PLL synthesized control. Powered by 12V DC. ¬ - ® ¯ ° ± ² ³ ´ ´ µ 11 1. Power: Pushes the receiver on and off. 2. Group LED Display: 3. Channel LED Display: 12 13 14 15 Displays group number. Displays channel number.
WIRELESS PRODUCT DESCRIPTION 4. Group Button: Press this button to choose a displayed group number and the setting group will be locked in 5 seconds. 5. Channel Button: Press this button to choose a displayed channel number and the setting channel will be locked in 5 seconds. 6. Set Button: Press this button to choose a displayed group or channel number. 7. RF Level Indicators: Five LEDs per RF antenna channel glow to indicate RF signal strength.
WIRELESS PRODUCT DESCRIPTION 5.2 Handheld Microphone The handheld microphone operates in UHF band frequency with PLL synthesized control. UHF 16-or 64 preprogrammed selectable frequencies to avoid interference. Uni-directional dynamic or uni-directional electret condenser capsules with different characters for various choices. Use 1.5V x 2 AA size batteries for low operating cost. ¬ - ® ° 1 8 2 3 7 6 4 5 GR. 81 2 7 3 6 4 5 CH. ¯ CHANNEL SELECTOR ± ² ´ ³ 1.
WIRELESS PRODUCT DESCRIPTION 5.3 Bodypack Transmitter The bodypack transmitter operates in UHF band frequency with PLL synthesized control. UHF 16 or 64 preprogrammed selectable frequencies to avoid interference. Uni-directional condenser capsules with different characters for various choices. Use 1.5V x 2 AA size dry or rechargeable batteries for low operating cost. ° ® ¯ - µ ± ´ ¬ 12 13 ² ³ 1. On/Off Switch: Turns transmitter power on and off. 2. Mini XLR /3.
WIRELESS BASIC CONNECTIONS 6. Basic Connections Connect the receiver output to the audio mixer or amplifier input, using a standard audio cable with 3-pin XLR connectors or 6.3j phone plugs. Never use the balanced and unbalanced audio outputs at the same time! This may cause signal loss or increased noise.
WIRELESS SETTING UP 7. Setting Up NOTICE: Prior to setting up, check that the transmitter and receiver are tuned to the same frequency. Two or above transmitters operating in the same frequency can not be used at the same time and area, so please select the different frequencies which can be used simultaneously at local area. 7.1 Connecting the receiver to power Ø Plug the antennas into the TNC socket on the receiver and point them upward.
WIRELESS TROUBLE SHOOTING 7.5 Setting up the bodypack transmitter A. Connecting a microphone Ø Open the battery cover. Push the MIC/LINE switch to “MIC” and use the supplied screwdriver to adjust the GAIN at appropriate position. Ø Plug the mini XLR connector (3.5j plug) of the microphone cable into the audio input connector on the bodypack transmitter. Ø Switch the transmitter and hi-fi appliance (amplifier, tape deck etc.) power on. Ø Test the microphone and adjust the levels on your mixer or amplifier.
WIRELESS FEATURES & SPECIFICATIONS 9. System Feature Ø Operating in UHF band frequency with synthesizer controlled. Ø The wireless microphone system with 16 or 64 selectable frequencies via Phase Locked Loop (PLL) circuitry makes it easy to choose non-interfered channels. Ø Super high sensitivity, extremely low noise transmission and reception. Ø SMT assembled PCB module ensures the quality and stability. 10.