IC3 | IC3-AW | IC6 | IC6-HT | IC6-ST IC8 | IC8-AW | IW5-LCR | IW6 user’s manual Register your warranty online at www.MartinLogan.com. See your local MartinLogan dealer for new construction pre-install brackets (sold separately).
Content Check List . . . . . . . . . . . . . . . . . 2 Safety Warnings and WEEE Recycling . . . . 2 Square Grilles, Pre-Installation Brackets, & Fire Rated Backboxes . . . . . . . . . . . . 3 Protect Your Investment . . . . . . . . . . . . . . 6 Break-In . . . . . . . . . . . . . . . . . . . . . . . . 6 General Speaker Placement . . . . . . . . . . . 6 Placement Options (IC3, IC3-AW IC6, IC8, IC8-AW, IW5-LCR, IW6 Speakers) . . . . . . 7 Placement Options (IC6-ST Stereo Speaker) . .
In accordance with the European Union WEEE (Waste Electrical and Electronic Equipment) directive effective August 13, 2005, we would like to notify you that this product may contain regulated materials which upon disposal, according to the WEEE directive, require special reuse and recycling processing. For this reason MartinLogan has arranged with our distributors in European Union member nations to collect and recycle this product at no cost to you.
Fig. 1a Multiple speakers, distributed audio. Fig. 2b IC6-ST: Wide dispersion surrounds in a 5.1-channel system using two speakers. Fig. 2d IC6-ST: Surround and rear channels in a 7.1-channel system using two speakers. 4 Fig. 2a IC6-ST: 2-channel sound from a single speaker. Fig. 2c IC6-ST: Wide dispersion rear in a 6.1-channel system using one speaker. Fig. 2e IC6-ST: Rear channels in a 7.1-channel system using one speaker.
˝ Min. 12 ˝ Min. 12 ´ ´ 10 -14 ´ ´ 10 -14 Fig. 3a Fig. 3b IC6-HT: Front left and right speakers. IC6-HT: Front left, center, and right speakers. Fig. 3c Fig. 3d ˝ Min. 12 IC6-HT: Non-direct surround channels in a 5.1-channel system. ˝ Min. 12 IC6-HT: Non-direct rear channel in a 6.1-channel system. ˝ Min. 12 ˝ Min. 12 Fig. 3e ˝ Min. 12 IC6-HT: Non-direct rear channels in a 7.1-channel system. Fig. 3f IC6-HT: Direct radiating surround and rear channels in a 7.1-channel system.
Protect Your Investment • Use an amp that approximately matches the speaker's specified power handling. • To avoid damage, turn down the volume if the speaker sounds like it is distorting, sounds harsh, or the bass begins to break up. • Tone controls and equalizers may increase the likelihood of distortion, especially at high volumes. Use these settings sparingly. Break-In When you first begin to play your speakers, they will sound a bit bass shy.
When choosing placement follow these simple tips: • Place a minimum of 12-inches (30cm) from any wall corner. • Place fronts/centers equidistant between 10–14 feet (3–4.3m) from the listening position. • IC6-HT: Install in-ceiling only. Placement Options (IC3, IC3-AW, IC6, IC8, IC8-AW, IW5-LCR, IW6) Stereo and Home Theater Applications (no illustration) MartinLogan Installer Series in-wall and in-ceiling speakers are ideal for 2-channel stereo and multi-channel home theater installations.
toward the front of the room and the other points toward the back. Connect the amp's left and right surround and rear channels to the appropriate speakers. 7.1-Channel System: Rear Placement Using One Speaker (Fig. 2e) Center one IC6-ST behind the listening area with tweeters positioned toward the left and right sides of the room. Connect the amp's left and right rear channels to the speaker.
Connection ALL MODELS EXCEPT “IC6-ST” (2 SPEAKER STEREO SETUP) L RECEIVER / AMPLIFIER Connect the red (+) amplifier terminal to the red (+) speaker terminal. Connect the black (-) amplifier terminal to the black (-) speaker terminal. Fasten cable to bracket with wire tie (Fig. 4a). R L R - + + - Fig. 4a: Wiring for 2-channel stereo sound.
In-Ceiling Mounting (pictorial) Note: Before pushing speaker into ceiling or wall clamps must be positioned as shown. ✔ ✘ ✔ ✘ Fig. 5a Fig. 5b Fig. 5c Fig. 5d Fig.
In-Wall Mounting (pictorial) Note: Before pushing speaker into ceiling or wall clamps must be positioned as shown. ✘ ✔ Fig. 6a.1 Fig. 6a.2 Fig. 6b Fig. 6c Fig. 6d Fig.
Installation NOTE: These instructions assume the mounting surface is of standard wood frame and standard sheet rock construction. If you wish to mount the speakers to another type of material you should contact a bonded contractor. NOTE: See your local dealer for new construction pre-install brackets (sold separately). NOTE: While it is possible to use a manual screwdriver for installation, we strongly suggest using a power drill. To avoid damaging or breaking the clamps, set your drill to a LOW setting.
Take great care to assign the same color to the (+) terminal on both the speaker and the amplifier. IC6-ST: See the section, "Connecting the IC6-ST". 7. Set your power drill to the low setting. 8. Ensure the clamps on the lip of the speaker are positioned exactly as shown in the Warning Diagrams. 9. Gently push the assembly into the ceiling or wall hole (Figs. 5c & 6c). 10. Supporting the assembly with one hand, tighten each screw. Stop tightening when you sense resistance (Figs. 5d & 6d).
Frequently Asked Questions How do I clean my speakers? Use a dust free cloth or a soft brush to remove the dust from your speakers. Do not spray any kind of cleaning agent on or in close proximity to the drivers. What size amplifier should I use? We recommend an amplifier rated within the suitable amplifier range of your speaker.
Warranty MartinLogan offers online warranty registration at www.martinlogan.com. Your speaker is provided with an automatic Limited 90 Day Warranty coverage. You have the option, at no additional charge, to receive a Limited 5 Year Warranty coverage. To obtain the Limited 5 Year Warranty coverage register your speakers at www.martinlogan.com. Save a copy of your dealer receipt as it may be requested if service is required.
Specifications* IC3 System Frequency Response . . . . . . . . . . . . . 100–20,000 Hz ±3 dB Aiming . . . . . . . . . . . . . . . . . . . . . . . . . . . . N/A Sensitivity . . . . . . . . . . . . . . . . . . . . . . . . . . 88dB Impedance . . . . . . . . . . . . . . . . . . . . . . . . . Compatible with 8 ohms Crossover Frequency . . . . . . . . . . . . . . . . . . 1,800 Hz High-Frequency Driver . . . . . . . . . . . . . . . . . 0.75" (1.9cm) titanium domes Low-Frequency Driver . . . . . . .
IC3-AW IC6 100–20,000 Hz ±3 dB 55–20,000 Hz ±3 dB N/A N/A 88dB 89dB Compatible with 8 ohms Compatible with 8 ohms 1,800 Hz 3,000 Hz 0.75" (1.9cm) titanium domes 0.75" (1.9cm) titanium domes 3.5" (8.9cm) mineral-filled polypropylene cone 6.5" (16.5cm) mineral-filled polypropylene cone Push style accommodates wire up to 12AWG Push style accommodates wire up to 12AWG 15–100 Watts 15–80 Watts 60 Watts 50 Watts 1.2 lbs. each (0.5 kg) 3.5 lbs. each (1.6 kg) 4.1" x 4.17" (10.4 x 10.6cm) 8.
Specifications* IC6-HT System Frequency Response . . . . . . . . . . . . . 55–20,000 Hz ±3 dB Aiming . . . . . . . . . . . . . . . . . . . . . . . . . . . . Rotate speaker Sensitivity . . . . . . . . . . . . . . . . . . . . . . . . . . 89dB Impedance . . . . . . . . . . . . . . . . . . . . . . . . . Compatible with 8 ohms Crossover Frequency . . . . . . . . . . . . . . . . . . 2,500 Hz High-Frequency Driver . . . . . . . . . . . . . . . . . 1" (2.5cm) titanium dome Low-Frequency Driver . . .
IC6-ST IC8 52–20,000 Hz ±3 dB 45–20,000 Hz ±3 dB Rotate speaker N/A 89dB 90dB Compatible with 4 ohms mono / 8 ohms stereo Compatible with 8 ohms 3,000 Hz 2,500 Hz Two 0.75" (1.9cm) titanium domes 1" (2.5cm) titanium dome Dual voice-coil 6.5" (16.5cm) mineral-filled poly cone 8" (20.
Specifications* IC8-AW System Frequency Response . . . . . . . . . . . . . 45–20,000 Hz ±3 dB Aiming . . . . . . . . . . . . . . . . . . . . . . . . . . . . N/A Sensitivity . . . . . . . . . . . . . . . . . . . . . . . . . . 90dB Impedance . . . . . . . . . . . . . . . . . . . . . . . . . Compatible with 8 ohms Crossover Frequency . . . . . . . . . . . . . . . . . . 2,500 Hz High-Frequency Driver . . . . . . . . . . . . . . . . . 1" (2.5cm) titanium dome Low-Frequency Driver . . . . . . . .
IW5-LCR IW6 60–20,000 Hz ±3 dB 55–20,000 kHz ±3 dB N/A N/A 89dB 89dB Compatible with 8 ohms Compatible with 8 ohms 2,500 Hz 2,500 Hz 0.75" (1.9cm) titanium dome 0.75" (1.9cm) titanium dome Two 5.5" (14cm) mineral-filled polypropylene cones 6.5" (16.5cm) mineral-filled polypropylene cone Push style accommodates wire up to 12AWG Push style accommodates wire up to 12AWG 15–100 Watts 15–90 Watts 70 Watts 60 Watts 5.9 lbs. each (2.7 kg) 3.5 lbs. each (1.6 kg) 9.26" x 12.64" x 3.46" (23.
Lawrence, Kansas, USA www.martinlogan.com ©2018 MartinLogan. All rights reserved.
Lawrence, Kansas, USA www.martinlogan.com ©2018 MartinLogan. Tous droits réservés. Rev.