Pin 1 CW User Manual Professional Entertainment Technology
© 2013 Martin Professional A/S. Information subject to change without notice. Martin Professional A/S and all affiliated companies disclaim liability for any injury, damage, direct or indirect loss, consequential or economic loss or any other loss occasioned by the use of, inability to use or reliance on the information contained in this manual.
Table of contents Safety information ............................................................................................. 4 Introduction ....................................................................................................... 7 Fixture overview ................................................................................................ 7 Before using the product for the first time ......................................................... 7 Physical installation ..................
Safety information WARNING! Read the safety precautions in this manual before installing, powering, operating or servicing this product. The following symbols are used to identify important safety information on the product and in this manual: Warning! Safety hazard. Risk of severe injury or death. Warning! LED light emission. Risk of eye injury. Warning! Refer to manual before installing, powering or servicing. Warning! Hazardous voltage. Risk of lethal or severe electric shock.
Before using the fixture, check that all power distribution equipment and cables are in perfect condition and rated for the current requirements of all connected devices. Isolate the fixture from power immediately if the power plug or any seal, cover, cable, or other component is damaged, defective, deformed, wet or showing signs of overheating. Do not reapply power until repairs have been completed Do not expose the fixture to rain or moisture.
Fasten the fixture securely to a fixed surface or structure when in use. The fixture is not portable when installed. Ensure that any supporting structure and/or hardware used can hold at least 10 times the weight of all the devices they support. If suspending from a rigging structure, fasten the fixture to a rigging clamp. Do not use safety cables as the primary means of support.
Introduction The Pin 1 CW is a small, powerful pinspot incorporating a single 10 W long-life LED. It provides two focusable beam angles—7° and 11°—and is ideal for projecting onto mirror balls or other applications for mobile DJ’s or small fixed installations. Fixture overview 1. Power inlet 3. Safety cable attachment point 2. Heat sink (do not cover) 4. Focus ring Before using the product for the first time 1.
Physical installation The fixture is designed for indoor use only and must be used in a dry location with adequate ventilation. Always ensure that the fixture’s heat sink is not covered and always ensure that the product is firmly affixed. The fixture should be mounted via its screw holes on the bracket. Fastening the fixture to a flat surface The fixture can be fastened to a hard fixed flat surface that is oriented at any angle.
AC power Read Safety information on page 4 before connecting the fixture to AC mains power. For protection from electric shock, the fixture must be grounded (earthed). The power distribution circuit must be equipped with a fuse or circuit breaker and ground-fault (earth-fault) protection. Socket outlets or external power switches used to supply the fixture with power must be located near the fixture and easily accessible so that the fixtures can easily be disconnected from power.
Maintenance Read Safety information on page 4 before servicing the fixture. . Refer any service operation not described in this user manual to a qualified service technician. Disconnect mains power before cleaning or servicing the fixture. Fixtures must be serviced in an area where there is no risk of personal injury from falling parts, tools or other materials. Excessive dust, smoke fluid, and particle buildup degrades performance, can cause overheating and can damage the fixture.
To clean the fixture: 1. Disconnect the fixture from power and allow it to cool for at least 10 minutes. 2. Vacuum or gently blow away dust and loose particles from the outside of the fixture and the air vents at the back and sides of the head and in the base with low-pressure compressed air. 3. Clean the LED lenses by wiping gently with a soft, clean lint-free cloth moistened with a weak detergent solution. Do not rub the surface hard: lift particles off with a soft repeated press.
Specifications Physical Weight ...................................................................................... 1.1 kg (2.4 lbs.) Dimensions (W x H x D).................... 142 x 184 x 159 mm (5.6 x 7.2 x 6.3 in.) Optics Light source ........................................... 10 W Cree multi-chip cool white LED Beam angle ......................................................................................... 7° or 11° Minimum LED lifetime .....................
Electrical AC power ......................................................... 100 - 240 V, 50/60 Hz nominal Typical total power consumption* ............................................................. 10 W Typical power and current 110 V, 60 Hz ................................................................................ 0.15 A, 10 W 230 V, 50 Hz .................................................................................. 0.1 A, 10 W Measurements made at nominal voltage at full intensity.
RUSH Pin 1 CW user manual
I n n o v a t i o n Q u a l i t y P e r f o r m a n c e