MAC Encore™ Performance CLD and WRM Safety and Installation Manual
Dimensions All measurements are given in millimeters 731 452 550 254 740 585 238 ©2017-2018 HARMAN PROFESSIONAL DENMARK ApS. All rights reserved. Features, specifications and appearance are subject to change without notice. HARMAN PROFESSIONAL DENMARK ApS and all affiliated companies disclaim liability for any injury, damage, direct or indirect loss, consequential or economic loss or any other loss occasioned by the use of, inability to use or reliance on the information contained in this document.
Contents Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Packing . . . . . . . . . . . . . .
Safety Information WARNING! Read the safety precautions in this section before installing, powering, operating or servicing this product. The following symbols are used to identify important safety information on the product and in this document: DANGER! Safety hazard. Risk of severe injury or death. DANGER! Hazardous voltage. Risk of lethal or severe electric shock. WARNING! Fire hazard. WARNING! Burn hazard. Hot surface. Do not touch. WARNING! Intense light emission.
PROTECTION FROM ELECTRIC SHOCK • Do not remove any cover from the fixture except as described under “Service and maintenance” on page 13. • Disconnect the fixture from AC power before servicing it and when it is not in use. • Ensure that the fixture is electrically connected to ground (earth). • Use only a source of AC power that complies with local building and electrical codes and has both overload and ground-fault (earth-fault) protection.
• Do not expose persons to the fixture’s light output from a distance of less than 0.2 m (8 ins.). • Do not look at LEDs with magnifiers, telescopes, binoculars or similar optical instruments that may concentrate the light output. • Ensure that persons are not looking at the LEDs when the fixture lights up suddenly. This can happen when power is applied, when the fixture receives a DMX signal, or when certain control menu items are selected.
Introduction Thank you for selecting the MAC Encore Performance from Martin. This moving-head spotlight is available in CLD (cold white LED) and WRM (warm white LED) variants.
The SIP inserts are designed to protect the head without the tilt lock (see Figure 1) applied. Release the tilt lock before putting a fixture into a flightcase for transport. Leaving the tilt lock applied may cause damage that is not covered by the product warranty.
Physical installation Warning! The MAC Encore Performance has a powerful pan motor. The torque reaction when the head is panned suddenly can cause the base to move if the fixture is standing unsecured on a surface. Do not apply power to the MAC Encore Performance unless the base is securely fastened to a surface or to rigging hardware. Warning! Use two clamps to rig the fixture. Do not hang the fixture from only one clamp. Lock each clamp with both 1/4-turn fasteners.
Clamping the fixture on a truss 1. Check that all rigging hardware is undamaged and can bear at least 10 times the weight of the fixture or as required by locally applicable regulations. Check that the supporting structure can safely bear the weight of all installed fixtures, clamps, cables, auxiliary equipment, etc. and complies with locally applicable regulations. 2. Bolt each rigging clamp securely to an omega bracket with an M12 bolt (minimum grade 8.8) and self-locking nut.
AC power Warning! Read '“Safety Information” on page 4 before connecting the fixture to AC mains power. For protection from electric shock, the fixture must be electrically connected to ground (earth). The AC mains power distribution circuit must be equipped with a fuse or circuit breaker and ground-fault (earth-fault) protection. Power input Important! Connect the MAC Encore Performance directly to AC power. Do not connect it to a dimmer system; doing so may damage the fixture.
DMX data link The MAC Encore Performance has 5-pin locking XLR sockets for DMX and RDM input and output (see Figure 8 on page 11). The default pin-out on both sockets is: • pin 1 to shield • pin 2 to data 1 cold (-) • pin 3 to data 1 hot (+). Pins 4 and 5 are not used by the fixture but are bridged between input and output sockets. These pins can therefore be used as a pass-through connection for an additional data signal if required.
Service and maintenance Warning! Read “Safety Information” on page 4 before servicing the MAC Encore Performance. Warning! Disconnect the fixture from AC mains power and allow to cool for at least 30 minutes before handling. Do not stare into the light output. Be prepared for the fixture to light and move suddenly when connected to power.
3. You can let the head cover hang on its safety wire, but for easiest access push the cover’s safety wire retaining clip B in towards the head chassis, slide the clip until you can remove it, then remove the head cover completely from the fixture. A A B Figure 9: Access to the head 4. For easiest access to the components inside the head, position the head at an angle with the front facing downwards as shown in Figure 9, then apply the tilt lock. To reinstall the top head cover: 1. See Figure 9.
Access to the multi-module The multi-module contains the rotating gobo, color and animation wheels as well as the CMY flags. Access to these is easiest if you remove the module from the head. To remove the multi-module: 1. Remove the top head cover, position the head with the front glass angled downwards and the top side facing upwards, and apply the tilt lock (see “Access to the head” on page 13). 2. See Figure 10. Unhook the multi-module wiresets from their cutout A in the zoom/focus module chassis.
4. See Figure 12. Loosen the four Torx 20 screws D (arrowed) to release the multi-module, then lift the module out of the head and place it on a work surface as shown in Figure 12. D D D D Figure 12: Removing the multi-module 5. Use the steps above as a guide when reinstalling the multi-module. Check that you do not trap any wires during reinstallation. Do not disassemble the multi-module itself without service documentation or assistance from Martin Service.
Work in a clean, well lit area. Use gentle pressure only when cleaning. Do not use any product that contains abrasives. Do not use solvents. Use care when cleaning optical components: surfaces are fragile and easily scratched. To clean the fixture: 1. Disconnect the fixture from power and allow it to cool for at least 30 minutes. 2.
Gobo orientation The orientations shown in Figure 13 are correct in most cases, but consult your Martin dealer or gobo supplier if you are in any doubt about the orientation of a specific gobo type. Coated Glass Gobos The heavy matted aluminum coated borosilicate gobos in the MAC Encore Performance are factory-installed with the more reflective sides facing towards the light source. Replacement gobos must also be installed with more reflective sides facing the LEDs in order to avoid heat damage.
Replacing rotating gobos Important! A gobo can fall out of its holder if its spring is inserted the wrong way round. Do not lubricate gobo bearings: excess grease can cause loss of step. Correct gobo orientation is critical. Read the guidelines in Figure 13 carefully before installing a gobo. The MAC Encore Performance has a rotating gobo wheel with rotating texture/breakup gobos. Gobos are interchangeable. To replace a gobo: 1. Disconnect the fixture from power and allow it to cool for 30 minutes. 2.
5. See Figure 15. Rotate the goboholder until its magnet (arrowed) lines up with a reference point that you choose on the module chassis. Remove and insert any gobos you replace one by one, with the goboholder magnets lined up with your reference point, and avoid rotating the gobo wheel while a gobo is removed. This will keep gobos in the orientation they were designed for and avoid the need to reprogram the controller because a gobo orientation has changed during service. Figure 15: Goboholder magnet 6.
10. See Figure 18. Rotate the gobo in its holder if necessary to line up the alignment marks (arrowed) in the gobo and goboholder. 11. Insert the spring with the narrow end against the gobo, as shown in Figure 17. To identify the narrow end, press the spring flat: the narrow end is on the inside. Push the wide end of the spring in under the lip of the holder. 12. Check that the gobo is seated flush against the holder. Press the spring as flat as possible against the back of the gobo.
Replacing color filters The MAC Encore Performance has six dichroic color filters. See the MAC Encore Performance User Guide available for download from www.martin.com for filter names and part numbers. Use only genuine Martin™ color filters. Handle and store filters with care. Wear cotton gloves while handling them and keep them perfectly clean. To replace a color filter: 1. Disconnect the fixture from power and allow it to cool for 30 minutes. 2.
Using the fixture Before using the fixture, download and read the latest version of the MAC Encore Performance User Guide from the MAC Encore Performance Product Support page on the Martin website at www.martin.com. The User Guide contains details of: • The effects available in the fixture. • The control options available using DMX. • The setup, monitoring and control options available using the onboard control and display panel. • RDM (Remote Device Management) compatibility. • Software service functions.
Troubleshooting Problem Probable cause(s) Remedy No power to fixture. Check that power is switched on and cables are plugged in. Fuse blown or internal fault. Contact Martin Service or authorized service partner. Do not remove base or yoke covers, attempt to replace a fuse or carry out any repairs or service that are not described in this Safety and Installation Manual unless you have both authorization from Martin and official Martin service documentation. Bad data link.
Specifications Physical Length . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .452 mm (17.8 in.) Width (across yoke) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .480 mm (18.9 in.) Height (maximum) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .740 mm (29.2 in.) Height (head straight up) . . . . . . . . . . .
Photometric Data CLD variant Light engine luminous output. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ≥ 39 400 lumens Fixture luminous output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ≥ 11 600 lumens CRI (Color Rendering Index) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . > 80 CQS (Color Quality Scale) . . . . . . . . . . . . . . .
Approvals EU safety . . . . . . . . . . . . . . . . . . . . . . EN 60598-2-17, EN 62471, EN62493 EU EMC . . . . . . . . . . . . . . . . . . . . . . . . .EN 55015, EN 55032, EN 55103-2, EN 61000-3-2, EN 61000-3-3, EN 61547 US safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . UL 1573 US EMC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . FCC Part 15 Class A Canadian safety . . . . . . . . . . . . . . . . . . . . . . . . . .CSA C22.2 No.
Photobiological Safety Warning RISK GROUP 2 The label shown on the right is displayed on this product. If it becomes difficult or impossible to read, it must be replaced using the illustration on the right to reproduce a new label. CAUTION Possibly hazardous FCC Compliance optical radiation emitted from this product. Do not stare at operating lamp. May be harmful to the eyeV. This device complies with Part 15, Class A, of the FCC Rules.
www.martin.
