Wireless Ring Barcode Scanner Quick Guide For full user’s manual, please contact your local distributor.
FCC WARNING STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
BEEPER INDICATION INTRODUCTION Micro USB port LED Indicator (with Protective Cover) Function Button Restart Button (insert pin into the hole) Exit Window Touch-Activated Trigger Button Velcro Strap SPECIFICATIONS Sensor Resolution Indicator PCS Housing Profile Battery Life Charge Time Radio Coverage Symbologies Linear Image Sensor 4mil/ 0.1mm LED, Buzzer 30 Plastic(PC+ABS) BT HID, USB HID, USB VCP, Memory 6000 scans (1 scan/ 5 sec) 2.5 hours (fully charged) Bluetooth 4.1 (Class2) 10M/33ft.
OUT OF THE BOX CHARGING THE BATTERY Host Scanner USB A Wireless Ring Barcode Scanner USB Charger Cable Wirel ess Ring 1 Barcode Scanner 2 Quick Guide Micro USB 1. Flip open the micro USB port on the scanner. 2. Insert the micro USB connector into the port on the scanner and USB A connector into a USB port on the host PC. 3. Keep charging until the red LED indicator turns off.
STEP 1 - GETTING STARTED 1. Pull open the long end and insert your index finger through the loop. 3. Clench your fist and use your thumb to tap the touch-activated trigger button. A gentle touch on the button will work; there is no need to press with force. 2. Adjust and attach the long end for a comfortable fit. 4. Aim at the barcode you wish to scan.
STEP 3 - INTERFACE SELECTION ATTENTION 1. If either your hand or the Velcro strap is soaking wet, the Laser beam may automatically light up without touch trigger. The scanner can still work well in this condition but it will waste battery power, so it is recommended to dry both your hand and the Velcro strap. 2.
BT - HID GETTING CONNECTED 1. Scan [Disconnect] to delete previous pairing record. Alternatively, you may long-press the function button for 5 seconds until the the scanner emit two beeps. . E031$ *.E031$* *.E043$* *.F068$* *.F067$* Disconnect BT - HID SMARTPHONE/TABLET TOUCH KEYBOARD Please follow below instruction to toggle touch keyboard on smartphone/tablet. iOS To toggle iOS touch keyboard, please simply press the function button. 2. Scan [BT - HID]; the scanner will emit two beeps.
BT - HID POWER OFF TIMEOUT NUMERIC BARCODES The period of inactivity before auto power-off. Variable Timeout . B030$ *.B030$* *.B029$* SET MINUTE (Range: 00 ~ 60) . B029$ SET SECOND (Range: 00 ~ 60) The default timeout is 00 minute and 30 seconds. For example, to set the timeout as 5 minutes 30 seconds: 1. Scan [Set Minute] 2. Scan [0] & [5] on page 14. 3. Scan [Set Minute] 4. Scan [Set Second] 5. Scan [3] & [0] on page 14. 6. Scan [Set Second] No Timeout (Scanner Always On) . B021$ *.
GENERAL SETTINGS ILLUMINATION PREFERENCE . A001$ . F059$ DEFAULT LASER ALWAYS ON LED ON AFTER 1 SEC . P023$ *.F059$* *.F049$* *.F048$* *.F046$* . F049$ ABORT LASER ALWAYS ON LED AUTO-ADAPTIVE . A007$ . F048$ CHECK VERSION BEEPER LASER ALWAYS ON LED ALWAYS ON . F046$ LASER OFF LED ALWAYS ON . F018$ BEEP ON .
KEYBOARD LAYOUT . C009$ . C010$ ENGLISH (USA) JAPAN (106 key) . C018$ . C025$ ENGLISH (UK) CANADIAN (FRENCH) . C034$ . C012$ FRENCH CANADIAN (TRADITIONAL) . C029$ . C011$ GERMAN NORWEGIAN . C026$ . C014$ ITALIAN SWEDISH . C031$ .
KEYBOARD LAYOUT . C030$ . C017$ CZECH (QWERTY) BELGIAN (AZERTY) . C028$ . C022$ CZECH (QWERTZ) DUTCH . C027$ . C021$ HUNGARIAN (QWERTZ) DANISH . C032$ . C024$ HUNGARIAN (101 KEY) SLOVAK . C033$ . C016$ SWISS (GERMAN) BRAZILIAN (PORTUGUESE) . C023$ .
ENABLE SYMBOLOGIES . G010$ . A002$ ENABLE ALL CODE CODE 93 . N017$ . K010$ CODE 32 IATA . L014$ . L010$ UK PLESSEY TELEPEN . L001$ . N032$ MSI GS1 DATABAR . N010$ . N001$ INDUSTRIAL 2 OF 5 GS1 DATABAR LIMITED . N026$ .
TERMINATOR MEMORY MODE . D012$ . C035$ CR . D011$ MEMORY MODE *.c035$* LF After scanning the above barcode, the scanner will be able to collect barcode data off-line. The barcode data will be stored in the format of: < Date >, < Time >, < Barcode Data > < CR > CR + LF To retrieve stored data, please connect the scanner to the host with cable, access removable storage device “MiniScan” from which you may open or copy the file “BARCODE.txt” to your computer. . D013$ . D010$ NONE .
MEMORY MODE DATE & TIME SETUP MEMORY MODE DATA FORMAT . R011$ . R006$ *.R006$* SET DATE Example: To set Date to 2017-08-01 (Year-Month-Day): 1. Scan [Set Date] 2. Scan [1], [7], [0], [8], [0], [1] on page 14. 3. Scan [Set Date] DATA FORMAT *.R011$* The default Data Format is ,
MEMORY MODE DATE FORMAT MEMORY MODE . R008$ *.R008$* TIME FORMAT . R009$ DATE FORMAT TIME FORMAT *.
HOW TO REMOVE VELCRO STRAP 1. Pull open the long end. 3. Pull open the short end on the other side. 2. Pull out the long end through the slot. 4. Remove the whole Velcro strap from the scanner by pulling the long end.
HOW TO INSTALL VELCRO STRAP 1. Insert the short end through the slot, with Velcro side facing upwards. 3. Insert the long end through the other slot, with Velcro side facing upwards. 2. Attach the short end to the long end to close. 4. Attach the long end to itself to close.
TROUBLESHOOTING TEST BARCODES Code 39 CODE-39 TEST Interleaved 2 of 5 9876543210 Code 128 12345678 Q: Your Bluetooth is unable to detect the scanner. A: (1) Make sure your Bluetooth is 4.0 or later version that supports BLE. (2) Restart your Bluetooth or Host device and try again, following the instruction on page 11. (3) Make sure the scanner is in BT-HID mode (see page 10). If the scanner is discoverable, its LED indicator will be flashing Blue. (4) The scanner might be powered off.