Mini Wireless Barcode Reader Quick Guide For full user’s manual, please contact your local distributor.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
OUT OF THE BOX INTRODUCTION Micro USB port (w/ Protective Cover) Mini Wireless Barcode Reader Trigger Button NUMERIC BARCODES *1* *2* *3* *4* *5* Silicone Cover Mini Wireless 1 Barcode Reader Quick Guide 2 3 4 5 Quick Guide & Quick Connection Card USB Charger Cable Neck Strap -3- LED Indicator (1) iOS Hotkey Button (2) Delete Button SPECIFICATIONS Sensor Resolution Memory Indicator PCS Housing Profile Battery Life Charge Time Radio Coverage Symbologies Exit Window Linear CMOS sensor 4mil/ 0.
BEEPER INDICATION GETTING STARTED Single long beep Single beep Single short beep Two beeps To scan a barcode, make sure the aiming beam crosses every bar and space of the barcode. Two short beeps Four beeps (Hi-Lo-Hi-Lo) Five beeps Three beeps Three short beeps CHARGING THE BATTERY Host Scanner Several short beeps USB A Micro USB 1. Flip open the micro USB port on the scanner. 2.
INTERFACE INTERFACE There are 5 interfaces for data transmission/collection: . E043$ *.E043$* *.E042$* BT HID . E042$ BT SPP . C035$ *.c035$* *.c008$* *.C006$* Memory Mode . C008$ USB HID 1. BT HID - Emulates a Bluetooth HID keyboard that transmits each barcode data to the host after decode. (See page 9) 2. BT SPP - Emulates a Bluetooth SPP device that transmits each barcode data to the host after decode. (See page 9) 3.
GETTING CONNECTED PINCODE SETUP There are two modes of wireless communication: . E043$ *.E043$* [ Recommended ] BT mode - HID 1. Press the trigger for 1 second to activate the scanner. 2. Scan [DISCONNECT] 3. Scan [BT mode - HID]; the scanner will emit several beeps. 4. Select “Wireless Scanner” from discovered device list. 5. The Bluetooth application may prompt you to scan a pincode(see PINCODE SETUP section) it generated. 6. The scanner will beep twice to verify the connection. . E042$ *.
NUMERIC BARCODES *1* *2* *3* *4* *5* - 11 - 1 6 2 7 3 8 4 9 5 0 *6* *7* *8* *9* *0* - 12 -
SMARTPHONE/TABLET CONNECTION Getting Connected - iOS & Android BATCH MODE . E054$ ENABLE . E053$ DISABLE Simply follow instruction in [BT mode - HID] (page 9) ,in which step 5 can be skipped since iOS & Android will not require pin-code for connection. Touch Keyboard - iOS iOS Hotkey Button In Batch Mode, data will be temporarily stored in memory buffer (2KB RAM) when the scanner is out of range or in poor connection quality.
POWER OFF TIMEOUT BINARY CHECK CHARACTER The period of inactivity before auto power-off. Variable Timeout . E029$ ENABLE . B030$ *.B030$* *.B029$* SET MINUTE (Range: 00 ~ 60) . B029$ SET SECOND (Range: 00 ~ 60) The default timeout is 3 minutes 0 second. For example, to set the timeout as 5 minutes 30 seconds: 1. Scan [Set Minute] 2. Scan [0] & [5] on page 11 & 12. 3. Scan [Set Minute] 4. Scan [Set Second] 5. Scan [3] & [0] on page 11 & 12. 6. Scan [Set Second] .
GENERAL SETTINGS READING MODE . A001$ . F002$ DEFAULT TRIGGER . P023$ . F001$ ABORT FLASH . F005$ . A007$ CHECK VERSION BEEPER CONTINUOUS VIBRATOR . F012$ . D035$ BEEP OFF VIBRATOR OFF . F018$ *.D035$* *.D034$* .
KEYBOARD LAYOUT . C010$ ENGLISH (USA) JAPAN (106 key) ENGLISH (UK) CANADIAN (FRENCH) FRENCH CANADIAN (TRADITIONAL) . C018$ . C009$ . C025$ . C034$ . C012$ . C029$ . C011$ GERMAN NORWEGIAN . C026$ . C014$ ITALIAN SWEDISH . C031$ .
KEYBOARD LAYOUT . C017$ CZECH (QWERTY) BELGIAN (AZERTY) . C030$ . C028$ . C022$ CZECH (QWERTZ) DUTCH . C027$ . C021$ HUNGARIAN (QWERTZ) DANISH . C032$ . C024$ HUNGARIAN (101 KEY) SLOVAK SWISS (GERMAN) BRAZILIAN (PORTUGUESE) . C033$ . C016$ . C023$ SWISS (FRENCH) - 21 - .
ENABLE SYMBOLOGIES . G010$ . A002$ ENABLE ALL CODE CODE 93 . N017$ . K010$ CODE 32 IATA . L014$ . L010$ UK PLESSEY TELEPEN . L001$ . N032$ MSI GS1 DATABAR INDUSTRIAL 2 OF 5 GS1 DATABAR LIMITED MATRIX 2 OF 5 GS1 DATABAR EXPANDED . N010$ . N001$ . M010$ - 23 - .
MEMORY MODE TERMINATOR . D012$ . C035$ CR . D011$ LF . D013$ CR + LF *.c035$* Memory Mode After scanning the above barcode, the scanner will be able to collect barcode data off-line. The barcode data will be stored in the format of: < Date >, < Time >, < Barcode Data > < CR > To retrieve stored data, please connect the scanner to the host with cable, access removable storage device “MiniScan” from which you may open or copy the file “BARCODE.txt” to your computer.
MEMORY MODE MEMORY MODE . R006$ *.R006$* . R011$ SET DATE Example: To set Date to 2014-08-01 (Year-Month-Day): 1. Scan [Set Date] 2. Scan [1], [4], [0], [8], [0], [1] on page 11 & 12. 3. Scan [Set Date] . R007$ *.R007$* SET TIME Example: To set Time to 08:10:30 am (Hr:Min:Sec) 1. Scan [Set Time] 2. Scan [0], [8], [1], [0], [3], [0] on page 11 & 12. 3.
MEMORY MODE MEMORY MODE . R008$ *.R008$* . R009$ DATE FORMAT TIME FORMAT *.
- 31 -
