Mini Wireless Barcode Reader Quick Guide For full user’s manual, please contact your local distributor.
FCC WARNING STATEMENT This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
OUT OF THE BOX INTRODUCTION Trigger LED Indicator Mini Wireless Barcode Reader Mini USB port (w/ Protective Cover) Exit Window NUMERIC BARCODES Mini Wireless Barcode Reader *1* *2* *3* *4* *5* Quick Guide Quick Guide 1 2 3 4 5 Quick Connection Card USB Charger Cable Hand Strap -3- SPECIFICATIONS Sensor Resolution Indicator PCS Housing Profile Battery Life Charge Time Radio Coverage Symbologies Linear CMOS sensor 4mil/ 0.
BEEPER INDICATION GETTING STARTED Single long beep Single beep Single short beep Two beeps To scan a barcode, make sure the aiming beam crosses every bar and space of the barcode. Two short beeps Four beeps (Hi-Lo-Hi-Lo) Five beeps Three beeps Three short beeps CHARGING THE BATTERY Host USB A Scanner Mini USB 1. Flip open the mini USB port on the scanner. 2. Insert the mini USB connector into the port on the scanner and USB A connector into a USB port on the host PC.
GETTING CONNECTED PINCODE SETUP There are two modes of wireless communication: . E043$ *.E043$* [ Recommended ] BT mode - HID 1. Press the trigger for 1 second to activate the scanner. 2. Scan [DISCONNECT] 3. Scan [BT mode - HID]; the scanner will emit several beeps. 4. Select “Wireless Scanner” from discovered device list. 5. The Bluetooth application may prompt you to scan a pincode(see PINCODE SETUP section) it generated. 6. The scanner will beep twice to verify the connection. . E042$ *.
NUMERIC BARCODES *1* *2* *3* *4* *5* -9- 1 6 2 7 3 8 4 9 5 0 *6* *7* *8* *9* *0* - 10 -
POWER OFF TIMEOUT The period of inactivity before auto power-off. Variable Timeout Simply follow instruction in [BT mode - HID] (page 7) ,in which step 5 can be skipped since iOS & Android will not require pin-code for connection. . B030$ *.B030$* *.B029$* SMARTPHONE/TABLET CONNECTION Getting Connected - iOS & Android SET MINUTE (Range: 00 ~ 60) . B029$ SET SECOND (Range: 00 ~ 60) The default timeout is 3 minutes 0 second. For example, to set the timeout as 5 minutes 30 seconds: 1.
INTERFACE SELECTION BATCH MODE . E043$ *.E043$* *.E042$* *.C008$* *.C006$* . E054$ BT HID ENABLE . E042$ . E053$ BT SPP . C008$ USB HID . C006$ USB VCP 1. BT HID - Emulates a Bluetooth HID keyboard that transmits each barcode data to the host. (see page 9 for defails) 2. BT SPP - Emulates a Bluetooth SPP device that transmits each barcode data to the host. (see page 9 for details) 3. USB HID - Emulates a USB keyboard that transmits each barcode data to the host. 4.
GENERAL SETTINGS READING MODE . A001$ . F002$ DEFAULT TRIGGER . P023$ . F003$ ABORT TOGGLE . A007$ CHECK VERSION BEEPER . F001$ FLASH . F005$ CONTINUOUS . F012$ BEEP OFF . F018$ BEEP ON - 15 - .
KEYBOARD LAYOUT . C010$ ENGLISH (USA) JAPAN (106 key) ENGLISH (UK) CANADIAN (FRENCH) FRENCH CANADIAN (TRADITIONAL) . C018$ . C009$ . C025$ . C034$ . C012$ . C029$ . C011$ GERMAN NORWEGIAN . C026$ . C014$ ITALIAN SWEDISH . C031$ .
KEYBOARD LAYOUT . C017$ CZECH (QWERTY) BELGIAN (AZERTY) . C030$ . C028$ . C022$ CZECH (QWERTZ) DUTCH . C027$ . C021$ HUNGARIAN (QWERTZ) DANISH . C032$ . C024$ HUNGARIAN (101 KEY) SLOVAK . C033$ . C016$ SWISS (GERMAN) . C023$ SWISS (FRENCH) - 19 - BRAZILIAN (PORTUGUESE) .
ENABLE SYMBOLOGIES . G010$ . A002$ ENABLE ALL CODE CODE 93 . N017$ . K010$ CODE 32 IATA . L014$ . L010$ UK PLESSEY TELEPEN . L001$ . N032$ MSI GS1 DATABAR INDUSTRIAL 2 OF 5 GS1 DATABAR LIMITED MATRIX 2 OF 5 GS1 DATABAR EXPANDED . N010$ . N001$ . M010$ - 21 - .
TERMINATOR . D012$ CR . D011$ The following pages only apply to the memory version mini wireless scanner. LF . D013$ CR + LF . D010$ NONE The firmware version with suffix “MEM” supports memory function. e.g. SM3-c-X.XX.BTA.MEM The firmware version can be found either on the scanner box or by scanning below barcode. . A007$ . D015$ SPACE CHECK VERSION .
MEMORY MODE For memory version only DATA FORMAT For memory version only . R011$ . C035$ *.c035$* DATA FORMAT MEMORY MODE After scanning the above barcode, the scanner will be able to collect barcode data off-line. The barcode data will be stored in the format of: < Date >, < Time >, < Barcode Data > < CR > To retrieve stored data, please connect the scanner to the host with cable, access removable storage device “MiniScan” from which you may open or copy the file “BARCODE.txt” to your computer.
DATE FORMAT For memory version only TIME FORMAT . R008$ *.R008$* For memory version only . R009$ DATE FORMAT TIME FORMAT *.
DATE & TIME SETUP For memory version only . R006$ *.R006$* SET DATE Example: To set Date to 2012-08-01 (Year-Month-Day): 1. Scan [Set Date] 2. Scan [1], [2], [0], [8], [0], [1] on page 9 & 10. 3. Scan [Set Date] TEST BARCODES Code 39 CODE-39 TEST Interleaved 2 of 5 . R007$ *.R007$* SET TIME Example: To set Time to 08:10:30 am (Hr:Min:Sec) 1. Scan [Set Time] 2. Scan [0], [8], [1], [0], [3], [0] on page 9 & 10. 3.