MRU-F5100US User’s manual This document describes the operation of the application to perform standard operations on the MRU-F5100US (hereinafter called “MRU”). 1. Preparation 1.1. Preparation (Hardware) ⚫ ⚫ ⚫ ⚫ PC installed Windows7 or later LAN cable MRU-F5100US Antennas and cables 1.2. Connection ⚫ ⚫ ⚫ Connecting power source to the MRU.
3. Launch “FRUSample.exe” Double-click “FRUSample.exe”. When “FRUSample.exe” starts, following screen is displayed.
4. Connection with MRU Select “Connection” – “LAN” in the menu. Then following screen is displayed. And enter the IP address of the MRU in “IPAddress”. ※ When the software starts, the default IP address is displayed.
Click the “Connect” button to connect to MRU. When the “Connect” is completed successfully, IP address is displayed in the title area and “Successed to Connect to FRU” is displayed in the status area.
. MRU Settings Set the necessary settings in advance to read UHF tags with the MRU. 5.1. Start to MRU operation Click “OpenRd” button in the “Reader” tab. When the operation is successfully started, “00 Normal” is displayed in the RESULT area.
5.2. Antenna settings Set the antenna to be used in the “AntConf” tab. ※ Change the current MRU antenna settings. In the operation with multiple antennas enabled, use Antenna 0 first and when either Dwell or InvCnt reaches the maximum value, it switches to the next antenna. When all antennas are used, return to Antenna 0 and continue to read.
To change the antenna settings, enter the antenna settings and click the “SetAntConf” button. If the antenna settings are successfully changed, “00 Normal” is displayed in the RESULT area.
6. Tag Reading Operation 6.1. Start reading Select “Report” in “Method” of “Inventory” tab and click “StartInv” button. Select “Report” If “StartInv” is successful, “00 Normal” is displayed in the RESULT area. While reading tags, the read tag information is displayed at the bottom of the screen.
Read tag information is displayed. Click the “TagView” button to see the details of the read tag.
When you click the “TagView” button, the following screen is displayed, and the read tag information is updated in real time. 6.2. Stop reading Click the “StopInv” button to stop reading tags. If the stop is successful, “00 Normal” is displayed in the RESULT area.
7. Stop to MRU operation Click the “ClosedRd” button in the “Reader” tab. If the operation of the MRU is successfully stopped, “00 Normal” is displayed in the RESULT area.
8. Quit the application Select “Connection” – “LAN” in the menu. Then following screen is displayed. And click “Disconnect” button. When the “Disconnect” is completed successfully, “[NotConnected]” is displayed in the title area.
Click “X” button to quit the application.
Appendix A Connection with MRU by RS-232C Connect PC to MRU as below. MRU-F5100US and Antenna connection example for RS-232C MRU-F5100US DC Power Or PoE PC or Host Controller RS-232C Cross Cable Antenna Cable RS-232C Conversion Cable DIN Antennas DOUT Select “Connection” – “RS-232C/USB” in the menu. Then following screen is displayed. And enter the PortName of the COM port ※Baudrate default is 115200 Click the “Connect” button to connect to MRU.
Appendix B FCC Federal Communications Commission (FCC) Statement 15.21 You are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the user’s authority to operate the equipment. 15.105(b) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
