User's Manual

ManualsBrandsMarathon Watch ManualsElectronicsTHERMO SENSOR

Table Of Contents

The remote sensor should be securely mounted onto a horizontal surface.

USER MANUAL

1. Features

1.1 Time - Radio Controlled Time (RC-WWVB)

- 12/24 hour time display selectable

- Daily Snooze Alarm function

- Day of week in 3 languages user selectable

1.2 Temperature - Indoor measurable range: -10°C ~+ 50°C

- Measures °C / °F user selectable

- Outdoor measurable range: -20 ~ 50°C

1.3 Wireless Outdoor Sensor - 433.92 MHz RF receiving frequency

- Transmission range: 70 meters (open area)

- Low-battery indicator for Outdoor Thermo

Sensor

- Wall Mount or Table Stand

2. Unit Appearance

Part A:

A1: Radio Controlled Icon

A2: Time Display

A3: Indoor Temperature

A4: Date, Day of Week

Summary of content (7 pages)

PAGE 1
USER MANUAL 1. Features 1.1 Time - Radio Controlled Time (RC-WWVB) 12/24 hour time display selectable Daily Snooze Alarm function Day of week in 3 languages user selectable 1.2 Temperature - Indoor measurable range: -10°C ~+ 50°C - Measures °C / °F user selectable - Outdoor measurable range: -20 ~ 50°C 1.3 Wireless Outdoor Sensor - 433.92 MHz RF receiving frequency - Transmission range: 70 meters (open area) - Low-battery indicator for Outdoor Thermo Sensor - Wall Mount or Table Stand 2.
PAGE 2
A5: Outdoor Temperature Part B: B1: “MODE” Button B2: “SNOOZE” Button B3: “ALARM” Button B4: “+/12/24” Button Part C: C1: Wall Mount Hole C2: Battery Compartment B5:”- / ” Button B6: “RF SEARCH” Button B7: “RESET” Button B8: “ALERT” Button C3: Stand Outdoor Thermo Sensor(Model Name: CL030027A，CL030066A ) D1: Transmission Indication LED D5: “RESET” button D2: Temperature Display D3: Battery Compartment D4: Wall Mount Hole D6: “C/F” button D7: Stand D8: Cable probe 4. Getting Started: 4.
PAGE 3
4.2 Outdoor Thermo Sensor  Battery compartment (D3) of thermo sensor is locating behind the back cover, unscrews the batteries cover to open.  Insert 2 x AAA batteries observing polarity [ “+” and “–“ marks] 5. Installation 5.1 Main Unit The main unit can be placed onto any flat surface (C3), or wall mounted by the hanging hole (C1) at the back of the unit. 5.2 Outdoor Thermo sensor The remote sensor should be securely mounted onto a horizontal surface.
PAGE 4
 The clock automatically scans the time signal at 2.00 a.m. every day to maintain accurate timing. If reception fail, scanning stops (“  ” on LCD disappear) The clock can be set to scan the time signal manually by holding “ ” button for 3 seconds. Each reception takes about 5 minutes.    Stop scanning by holding “ ” button for 3 seconds. Set RCC function to “on” in setting mode, then hold “+” to select the time zone.
PAGE 5
time setting. Press “+” or “-” button to adjust the alarm time. Press “MODE” button to confirm the setting. 7.4 Snooze Alarm Function:  Press “ALARM” button to activate or deactivate the alarm. If the alarm is on, alarm icon " " appears on the display.  Press “SNOOZE” button when alarm alerts. The alarm snoozes for around 5 minutes, then it alerts again. “ ” flashes on the LCD during the snooze time. This process can be repeated for 7 times.
PAGE 6
as follow: Upper limit of temperature, Lower limit of Temperature.  When it’s alert, the corresponding icon “ ” or “ ” and temperature digit would flash on the LCD. Press any buttons to stop the alert sound. 8.2 The use of Temperature Probe:  Insert the probe plug to the jack on the right hand side of the thermo sensor unit.  Put the cable outside and leave the thermo sensor unit in indoor area to avoid freezing up the battery when the outdoor temperature is below -20 °C.
PAGE 7
interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver.