Service Manual DV4200 /U1B, /F1N, /N1B, /N1G, /S1G, /A1B DVD Player DVD PLAYER DV4200 OPEN/CLOSE STANDBY STOP PLAY STANDBY/ON POWER PAUSE TABLE OF CONTENTS SECTION PAGE 1. TECHNICAL SPECIFICATIONS ................................................................................................................ 1 PRODUCT SAFETY SERVICING GUIDELINE FOR VIDEO PRODUCTS ................................................ 2 SERVICING PRECAUTIONS ..............................................................
MARANTZ DESIGN AND SERVICE Using superior design and selected high grade components, MARANTZ company has created the ultimate in stereo sound. Only original MARANTZ parts can insure that your MARANTZ product will continue to perform to the specifications for which it is famous. Parts for your MARANTZ equipment are generally available to our National Marantz Subsidiary or Agent. ORDERING PARTS : Parts can be ordered either by mail or by Fax.. In both cases, the correct part number has to be specified.
REMARK This service manual corresponds to service modification code number "MZ01" and later. When exchanging MAIN PCB on the product of the service modification code "MZ00", it is necessary to also exchange the following parts on the I/O PCB simultaneously. (The service modification code is mentioned in the number label on the rear panel. Ex.MZ01xxxxxxxxxx) Two kinds of MPEG ICs (IC501) exist in this model. Since the conventional IC (Pantera-2) became a production stop, this was generated.
2. PRODUCT SAFETY SERVICING GUIDELINES FOR VIDEO PRODUCTS CAUTION : DO NOT ATTEMPT TO MODIFY THIS PRODUCT IN ANY WAY, NEVER PERFORM CUSTOMIZED INSTALLATIONS WITHOUT MANUFACTURER’S APPROVAL. UNAUTHORIZED MODIFICATIONS WILL NOT ONLY VOID THE WARRANTY, BUT MAY LEAD TO YOUR BEING LIABLE FOR ANY RESULTING PROPERTY DAMAGE OR USER INJURY. SERVICE WORK SHOULD BE PERFORMED ONLY AFTER YOU ARE THOROUGHLY FAMILIAR WITH ALL OF THE FOLLOWING SAFETY CHECKS AND SERVICING GUIDELINES.
3. SERVICING PRECAUTIONS Electrostatically Sensitive (ES) Devices Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field effect transistors and semiconductor chip components. The following techniques should be used to help reduce the incidence of component damage caused by static electricity.
4. CONNECTION FACILITIES 4.1 Video performance (N only) 1 3 5 7 9 11 13 15 17 19 21 2 4 6 8 10 12 14 16 18 20 4.1.1 SCART Pin No. Pin 1 Pin 2 Pin 3 Pin 4 Pin 5 Pin 6 Pin 7 Pin 8 Pin 9 Pin 10 Pin 11 Pin 12 Pin 13 Pin 14 Pin 15 Pin 16 Pin 17 Pin 18 Pin 19 Pin 20 Pin 21 TV (OUT) Pin No.
5. INFORMATIONS REGION CODE VERSION THE DISCS THAT THE DV4200 CAN HANDLE REGION CODE The following discs can be played back with DV4200. COUNTRY /UXX 1 USA/CANADA /FXX 2 JAPAN /NXX 2 EUROPE /SXX 3 SINGAPORE/HONGKONG /AXX 4 AUSTRALIA Types of playable discs and their marks Diameter/ Playable sides Playback time DVD VIDEO DVD VIDEO DVD INFORMATION Below is a glossary of the new terms related to DVD. Digital audio Digital video (MPEG 2) 12 cm (5in.
REMOTE CONTROL POWER POWER BUTTON REPEAT BUTTON SETUP BUTTON SUBTITLE BUTTON AUDIO BUTTON OPEN/CLOSE SETUP REPEAT A-B RANDOM AUDIO SUBTITLE ANGLE SURR. TOP MENU OPEN/CLOSE BUTTON A-B BUTTON RANDOM BUTTON ANGLE BUTTON SURR.
6. SERVICING HINT SERVICE HINTS SERVICE TOOLS Audio signals disc Disc without errors (SBC444)+ Disc with DO errors, black spots and fingerprints (SBC444A) Disc (65 min 1kHz) without no pause Max. diameter disc (58.
7. DISASSEMBLY CAUTION BEFORE STARTING SERVICING Electronic parts are susceptible to static electricity and may easily damaged, so do not forget to take a proper grounding treatment as required. Many screws are used inside the unit. To prevent missing, dropping, etc. of the screws, always use a magnetized screw driver in servicing. Several kinds of screws are used and some of them need special cautions.
7.2 CIRCUIT BOARD DISASSEMBLY Note: Before removing the main circuit board, be sure to shortcircuit the laserdiode output land. After replacing the main circuit board, open the land after inserting the flexible connector. (Refer to Mechanism Disassembly) 7.2.2 Key Circuit Board 7.2.1 Disassembling of Main Circuit Board and Interface Board 1. Remove the front panel.(See Fig. 2-3) 2. Release 4 screws (E), and remove the Key circuit board. 1. Remove the top case.(See Fig. 2-1) 2. Remove 12 screw (C). 3.
1 A 283 P0 PB 0 452 2 B 10 280 467 260 285 467 3 300 467 465 463 332 275 A48 465 279 462 463 465 A46 463 5 C A43 0 T0 PB 452 462 250 4 A00 463 463 8. EXPLODED VIEWS 8.
8.2 Packing Accessory Section 811 VIDEO 812 AUDIO 808 BATTERY 813 REMOTE 900 REMOTE CONTROLLER 801 USER GUIDE 804 PACKING SHEET 803 PACKING 803 PACKING 802 BOX CARTON POS. COLOR NO. A00 A43 A46 A46 A46 A46 A46 A48 250 260 275 280 280 280 280 280 280 283 283 285 300 300 300 300 332 401 452 462 463 465 467 PART NO. (FOR PCS) DESCRIPTON PART NO.
9. ELECTRICAL TROUBLESHOOTING GUIDE 9.1 Power (SMPS) Circuit A. B. No VF+ Is 5.2VA section working? NO NO No 5V_D or 5V_A . Is 5.2VA section working? YES YES Is oscillation present at the NO anode of D109? NO Is oscillation present at the Base of Q108? YES YES No 5.2VA. Replace D109. Replace Q108. Check R127, 128. (SHUTDOWN CKT) Is 5.2V applied to IC108 Pin 1? YES Check L103, C116. NO Check Fuse(F101). YES Is there a DC voltage at the (+) terminal of BD101? NO Replace BD101.
9.2 µ-COM Circuit A. No Power POWER ON Does Hello appear at FLD? YES NO Does no DISC appear? NO Is P5901 connected normally? YES NO Reconnect it. Does Logo appear on the screen? NO Check power. (Refer to power) If power is normal YES OK NO Is IC3F1 3.3Vcc? Refer to Front Part YES A NO Is pin3.5 of IC503 normal? YES Check short NO Is IC302, 303 Vcc? YES Check 3.3V. Replace Main B/D.
B. Audio abnormal C. Video abnormal AUDIO ABNORMAL VIDEO ABNORMAL Check Audio jack. Check Video jack. YES (If OK) YES (If OK) Check MPEG_CLK Signal of MPEG part. Refer to Video part. YES (If OK) YES (If OK) Refer to Audio part. Refer to Encoder part. YES (If OK) YES (If OK) Refer to MPEG part. Refer to MPEG part. YES (If OK) YES (If OK) Replace B/D. Replace B/D. D. Open/Close abnormal OPEN/CLOSE ABNORMAL Check Front. YES (If OK) Check the connection of P5901.
E. Picture abnormal PICTURE ABNORMAL Check the disc. Refer to Servo part If OK Check MPEG_CLK Signal of MPEG part YES (If OK) Check DSP YES (If OK) Check MPEG YES (If OK) Replace B/D F.
9.3 MPEG Circuit Power is on Does Logo appear on the screen? NO Check power & clock. YES YES Does the moving picture of the DVD Disc play on the screen normally? NO Is MPEG data signal normal? YES YES NO OK Check CD/DVD DSP output signal. OK Check MPEG Decoder input signal. YES Is error signal normal? NO Check CD/DVD DSP output signal. OK Check MPEG Decoder input signal.
9.4 Front Circuit (Digitron & key) START Power on. NO LED ON? NO Is oscillation of X901 normal? Check Power. YES YES Is Digitron on normally? NO CD YES Do all the buttons work normally? NO Check waveform of IC901 Pin 6. Replace IC902. YES NO Is waveform of IC901 Pin 40 normal? NO Check waveform of IC901 Pin 22. YES YES Check waveform of IC901 Pin 22. YES NO NO Solder Key part. Replace IC901. YES Solder defective parts again. Check waveform of IC901 Pin 26, 27.
9.5 RF/Servo Circuit A. CHECK POINT(General) Does signal goes "High" to IC201 Pin194 when the power is on? NO YES Does signal pulse input to IC201 Pins 58, 59 when the powe is on? NO Check "9.2 µ-COM Circuit". YES Does TTL pulse output to IC201 Pins 140, 142? NO YES Does 33.8688MHz clock input to IC201 Pin 63? YES Replace IC201 Is IC201 Pins 83, 84, 88, 89 voltage about 2.2V? NO Check power circuit.
B. No disc .Power on Does tray open or close? Check loading Part. NO Push Pick-up to inner track to the end by hand. YES Does PMD03 Pin 13 change high to low? NO DECK assembly is defective. (Limit sw) NO Check "9.2 µ-COM Circuit". YES Pressing the open/close key repeatedly, check the voltage of IC2M1 Pins 22 change 0V to 5V YES Does the voltage change at PMD03 Pins 1, 3 more than 2V on the basis of 3.8V? NO Replace IC2M1. YES DECK assembly is defective. Fig.1.
C. DISC IN OPEN/CLOSE Fig.3. FOCUS ERROR waveform NO FOCUS ON? Check the focus error moving the lens up and down. (IC2A1 Pin 42) NO IC201 no output : Pick-up is defective. YES YES Check IC2A1 Pin 11,12,13,14 in DVD Mode. Does the TTL level change at IC201 Pin 78 and 132 moving the lens? NO Replace IC201. YES Replace µ-COM or IC201. NO Does the disc turn? Check IC2M1 Pin 18, PMD03 Pin 6 turn when the IC2M1 Pin 21 is less than 2.2V.
D. CHECK A Fig.5. RF waveform Check RF Eye-Pattern. RF : 1.5-1.6V(IC2A1 Pin 57) NO No signal: Pick-up is defective Check IC2A1 Pins 5, 6, 7, 8. YES NO Is the eye-pattern vivid? YES Does the sawtooth waveform emit at IC2A1 Pin 41? NO NO Does the 1.6V emit? YES YES Check IC201 Pin84. Replace IC201. No signal at IC201 : IC201 is defective • Check IC201 Pin 162. • Check the clock at the IC201 Pins 28, 30. • Both are normal : IC201 is defective END 21 Replace IC2A1.
FOCUS,TRACKING,SLED LOADING DECK M ECHANI SM 22 POWER BOARD SPINDLE +1.8V +3.3V +3.3V_M +5V_A +5V_D +12VA +5.
SWITCHING TR RECTIFIER 23 AC85~140V (U, F) AC85~276V (A, S, N) TRANS FEED B. LPF LPF RECTIFIER(5.2V) LPF RECTIFIER(9V) RECTIFIER(14V) RECTIFIER(FLD) LINE FILTER PWR ON/OFF REG(3.3V) REG(3.3V) REG(8V) 1.8V 3.3V_M 3.3V 5V_A 5V_D 5.2VA 8V 12VA -24VA F- F+ 10.
M/D PICK UP Spindle 4 IC2A1 33P3721 RF Signal Processor 24 focus, tracking, loading, sled IC2M1 KA3017 SpindleMotor,LoadingMotor , Actuator Driver CD: A,B,C,D / E, F FDO,TDO,FMO MON,MDP MIRR,TZC DVD/CD RF FE,TE,PI,SBADD IC206 DVDSP-3301 CD / DVD DSP DVD SERVO DRAM 256K x 16bit Load open/close(loading control) SPINDLE_FG 2 4 ICADDR[ 0:8] 9 4 16 DVD: A,B,C,D, ICDATA[ 00:15] 8 8 MCK DVD_DATA[0:7] AO[0:5] DO[0:7] 8 6 XLAT, S_CLK, S_DATA DSP_CS, /WR, /RD 3 SQSO, SQCK, SCOR SENS,
MPEG I/F U-COM I/F 25 DA_DATA0 DA_XCK DA_BCK DA_LRCK DAC_L0 S_CLK S_DATA DAC_RST IC401 PCM1716E Audio DAC R L IC402 LPF & Buffer NJM4580D OP AMP R L A/V JACK I/F 10.
26 MCLK2 CKE MA[00:10] MA12,13 /CS0 /RAS/ /CAS /WE /DQM[0:3] 32 16 4 16 LADD[04:19] IC302/IC303 LATCH 16 IC3F1 FLASH MEMORY DAC_RST DAC_L0,DAC_L1 DA_BCK,DA_LRCK,DA_XCK DA_DATA[0:3} AD[04:19] ALE LA[0:3] AD[00:15] MD[00:31] CVBS Y/B(G) CVBS/G(R) /PWED IC501 PANTERA F_IN IC502 93C46 EEPROM V_MUTE,16:9 EE_CS IC305 SDRAM 16/32BIT 64M C/R(B) 4 8 8 ] /RD ZISENB /DSP_CS SENSE DSP_INT SDCLK1,PSYNC REQP SQCK,SQS0 SCLK,SDATA LA[0:3] DVD[0:7] AD[0:7] 00 19 : SPINDLE_FG I
AD0 ~ AD7 (only Data.) MD0 ~ MD31 (only Data) 27 DSP LA0 ~ LA3, (only Addr .) PANTERA PANTERA MA0 ~ MA13 (only Addr .) SDRAM LADD4,LADD5 (only Addr .) ALE AD4 ~ AD19 (Addr .&Data) AD0 ~ AD15 (only Data) LATCH IC (373) LADD4 ~ LADD19 (only Addr .) FLASH ROM CPLD LA0 ~ LA3 (only Addr .) XiO1,2,10 (CS & Enable) AD0 ~ AD19 (only Data) 10.
28
11. CIRCUIT DIAGRAMS 11.1 POWER (SMPS) CIRCUIT DIAGRAM IMPORTANT SAFETY NOTICE WHEN SERVICING THIS CHASSIS, UNDER NO CIRCUMSTANCES SHOULD THE ORIGINAL DESIGN BE MODIFIED OR ALTERED WITHOUT PERMISSION FROM THE MARANTZ ELECTRONICS CORPORATION. ALL COMPONENTS SHOULD BE REPLACED ONLY WITH TYPES IDENTICAL TO THOSE IN THE Q101 failure caused D101 failure. D101 is defective. ORIGINAL CIRCUIT. SPECIAL COMPONENTS ARE LITERATURE IS PRINTED. SHADED ON THE SCHEMATIC FOR EASY IDENTIFI- NOTE : CATION. 1.
11.2 DVD DSP CIRCUIT DIAGRAM Spindle Servo fail IC203 is defective. AD Converter Error - No tracking/Focus control 5 DRAM Control IC204 is defective. Scratched CD Audio abnormal.
11.3 DRIVE & RF CIRCUIT DIAGRAM CD/DVD picture abnormal 4 1 6 2 3 1 IC2A2 is defective. No fucus & tracking control. TRACKING LOOP SLED LOOP FOCUS LOOP SPINDLE LOOP Q2A1, Q2A2 are defective. CD/DVD LD will not be on.
11.4 MPEG CIRCUIT DIAGRAM System not operation 4.7 F/16V No power on 5 1 7 3 6 2 4 IC501 is defective. Optical out bad. WAVEFORM Y/Pb/Pr(Component) Y.c(S-VHS) Audio L/R OUT CVBS OPTICAL/COAXITAL OUT 35 Q507 is defective. Coaxial out bad.
• WAVEFORMS Tek Stop : 2.50MS/s 4 Acqs [T ] T 3 M20.
11.5 AUDIO DM CIRCUIT DIAGRAM IC403 is defective. Audio bad. Q401 is defective. 2CH Audio out bad. IC402 is defective. 2CH Audio out bad.
11.6 FRONT MICOM CIRCUIT DIAGRAM DIG901 is defective. FLD is distorted. RC901 is defective. R/C Error. IC902 is defective. Reset Error.
11.7 MEMORY CIRCUIT DIAGRAM R323 3.9K DAC RST Program download fail Digitron all not display and system not operate.
11.8 JACK CIRCUIT DIAGRAM SCART for N for U, F, S, A for N, S, A for F, N, S, A 16:9 can’t be changed Scart Mode can’t be changed for N OPTICAL COMP.
• CIRCUIT VOLTAGE CHART MODE PIN NO. EE PLAY DSP IC201 SP3301 MODE PIN NO. EE PLAY MODE PIN NO. EE PLAY MODE PIN NO. EE PLAY MODE PIN NO. EE PLAY MODE PIN NO. EE PLAY MODE PIN NO. EE PLAY MODE PIN NO. EE PLAY MODE PIN NO. EE PLAY MODE PIN NO. EE PLAY 54 3.10 3.00 109 0.00 0.00 164 1.40 1.40 10 2.02 2.07 6 1.10 1.10 2 3.12 3.40 57 2.95 2.88 28 3.01 3.00 83 0.27 2.83 55 3.10 3.00 110 0.00 0.00 165 3.20 0.00 11 0.10 0.00 7 1.10 1.10 3 2.
MODE PIN NO. EE PLAY MODE PIN NO. EE PLAY MODE PIN NO. EE PLAY MODE PIN NO. EE PLAY MODE PIN NO. EE PLAY MODE PIN NO. EE PLAY MODE PIN NO. EE PLAY MODE PIN NO. EE PLAY MODE PIN NO. EE PLAY MODE PIN NO. EE PLAY 37 2.56 1.84 5 0.00 0.00 11 0.00 0.00 14 0.00 2.09 25 0.00 1.70 80 3.14 3.10 135 2.22 2.20 190 0.00 0.00 4 0.00 0.00 19 4.78 4.76 38 0.00 0.00 6 0.00 0.00 12 0.00 0.00 15 4.91 4.92 26 0.00 1.40 81 2.95 3.10 136 3.07 3.
MODE PIN NO. EE 74 -17.20 -21.80 75 -17.20 -21.90 76 Emitter PLAY -17.10 -21.80 Q2M1 0.00 0.00 4.98 4.98 0.00 0.00 4.67 4.69 4.97 4.01 0.96 2.20 4.97 4.93 4.96 4.93 0.00 0.50 77 -17.50 -21.80 -17.30 -21.80 Q2A2 79 -17.30 -21.80 80 -16.80 -21.80 1 5.09 5.00 0.00 0.00 3 5.07 5.00 4.55 PLAY EE PLAY AUDIO Q401 5.04 5.33 4.32 5.03 4.08 0.00 Q402 5.04 5.03 5.03 4.99 0.00 0.00 Q403 0.00 0.00 0.00 0.00 5.03 5.02 Q404 0.00 0.00 -0.30 -0.30 0.
12. PRINTED CIRCUIT DIAGRAMS 12.1 MAIN P.C.
12.2 I/O P.C.
12.3 KEY P.C.BOARD 12.4 LED P.C.
13. ELECTRICAL PARTS LIST Resistance value CAPACITORS C : CERAMIC CAP. 3) DD1 × × × × 370, { Ceramic capacitor Disc type Temp.coeff.P350 N1000, 50V Capacity value Tolerance ➁ ➂ Examples ; ➁ Tolerance (Capacity deviation) ±0.25 pF .... 0 ±0.5 pF .... 1 ±5% .... 5 Tolerance of COMMON PARTS handled here are as follows : 0.5 pF 5 pF .... ±0.25 pF 6 pF 10 pF .... ±0.5 pF 12 pF 560 pF .... ±5% ➂ Capacity value 0.5 pF .... 005 3 pF .... 030 100 pF .... 101 1 pF .... 010 10 pF .... 100 220 pF .... 221 1.
POS. NO VERS. COLOR PART NO. (PCS) DESCRIPTION C403 nsp C405 C406 C407 C408 C409 C410 C411 C412 C413 C414 nsp nsp nsp nsp nsp nsp nsp nsp nsp nsp C415 C416 C417 C418 C419 C420 C421 C422 C424 nsp nsp nsp nsp nsp nsp nsp nsp nsp C425 C428 nsp nsp C429 C430 nsp nsp TUBULAR 0.1 F 50V +80% -20% ELECT 470 F 6.3V M TUBULAR 0.01 F 16V M ELECT 22 F 16V M ELECT 10 F 16V M ELECT 470 F 6.3V M ELECT 22 F 16V M TUBULAR 1000pF 50V K TUBULAR 100pF 50V J ELECT 10 F 16V M TUBULAR 0.
POS. NO ZD101 ZD101 ZD102 ZD605 ZD606 ZD607 ZD611 ZD612 ZD635 VERS. COLOR PART NO.
POS. NO VERS. COLOR R121 R122 R123 R124 R125 R126 R127 R128 R130 R131 R132 R140 R141 R144 N, A, S R144 F, U R145 R201 R204 R207 R217 R218 R219 R220 R221 R230 PART NO. (PCS) nsp 4822 053 10121 nsp nsp nsp nsp nsp nsp nsp nsp nsp nsp nsp nsp 4822 053 10121 nsp FILM METAL FILM FILM FILM FILM METAL METAL FILM FILM FILM FILM FILM FILM METAL FILM DESCRIPTION PART NO. (MJI) 1.2k 120 1k 330 3.9k 1k 3.6k 3.
POS. NO VERS. COLOR R401 R402 R403 R406 R407 R408 R409 R411 R412 R413 R414 R415 R416 R417 R418 R419 R420 R421 R422 R423 R427 R432 R501 R503 R504 R505 R506 R514 R515 R517 R520 R521 R522 R523 R524 R525 R527 R530 R533 R534 R535 R536 R537 R538 R539 R540 R541 R542 R588 R591 R597 R601 R602 R603 R604 R605 N, A, S N N N R609 R616 N R617 N R618 R619 R620 R621 R622 PART NO. (PCS) DESCRIPTION PART NO.
POS. NO VERS. COLOR PART NO. (PCS) DESCRIPTION POS. NO PART NO. (MJI) F602 VERS. COLOR PMD02 nsp F608 F612 F, A, S, U nsp F613 F, A, S, U nsp F615 nsp F616 nsp F617 N nsp F618 N nsp F622 N nsp FH101 FH102 nsp nsp FILTER CFI06B1H101MF 2.5K/T FILTER CFI06B1H101MF 2.5K/T FILTER CFI06B1H101MF 2.5K/T FILTER CFI06B1H101MF 2.5K/T FILTER CFI06B1H101MF 2.5K/T FILTER CFI06B1H101MF 2.5K/T FILTER CFI06B1H101MF 2.5K/T FILTER CFI06B1H101MF 2.
66
14. MECHANISM SECTION CONTENTS 5. Frame Assembly Up/Down ..............2-5 6. Belt Loading......................................2-5 7. Gear Pulley .......................................2-5 8. Gear Loading ....................................2-5 9. Guide Up/Down.................................2-5 10. PWB Assembly Loading ................2-5 11. Base Main........................................2-5 DECK MECHANISM PARTS LOCATIONS • Top View..................................................
DECK MECHANISM PARTS LOCATION • Top View (With Tray) Procedure Parts Fixing Type Starting No.
DECK MECHANISM DISASSEMBLY HOLDER CLAMP PLATE CLAMP CLAMP ASSEMBLY DISC TRAY DISC (A) MAGNET CLAMP CLAMP UPPER (S1) (S1) HOLDER CLAMP BASE MAIN (Fig. A) EMERGENCY EJECT HOLE BASE MAIN (L1) (A) LEVER (B) (L1) HOLDER CLAMP BASE MAIN BOTTOM SIDE VIEW Fig. 4-1 1. Holder Clamp (Fig. 4-1) Fig. 4-2 2. Tray Disc (Fig. 4-2) 1) Release 2 Screws(S1). 2) Unhook 2 Locking Tabs(L1). 3) Lift up the Holder Clamp and then separate it from the Base Main.
DECK MECHANISM DISASSEMBLY (L2) GEAR ASSEMBLY FEED GEAR MIDDLE (S2) GEAR ASSEMBLY RACK (S2) (S2) (S3) PICK UP ASSEMBLY GENERAL BASE PU(OUTSERT) (C1) (S2) RUBBER REAR GEAR ASSEMBLY FEED PICK UP ASSEMBLY GENERAL GEAR MIDDLE GAER ASSEMBLY RACK MOTOR ASSEMBLY SPINDLE MOTOR ASSEMBLY SPINDLE Fig. 4-3 3. Base Assembly Sled (Fig. 4-3) 1) Release 4 Screw(S2). 2) Disconnect the FFC Connector(C1) 3-2. Gear Middle 3-3. Gear Assembly Rack 1) Release the Scerw(S3) 3-1.
DECK MECHANISM DISASSEMBLY GUIDE UP/DOWN GEAR LOADING (L3) (L6) GEAR PULLEY (L6) (L4) BASE MAIN BELT LOADING (H1) PWB ASSEMBLY LOADING (L6) (S5) BASE MAIN (A) (A) (S4) (B) GUIDE UP/DOWN FRAME ASSEMBLY UP/DOWN (A) (L5) (B) FIG. (A) FIG. (B) (C) (B) GUIDE UP/DOWN GUIDE UP/DOWN FIG. (C) Fig. 4-4 5.
DECK MECHANISM ADJUSTMENT 1. Tools and Fixtures for SVC • For SVC Program Down-Load Not spare parts Fig.1. Printer Cable Included in Fig.2. FFC Cable (15 pin) PART NO.*DV3100JIG Fig.3. Jig Board Fig.4. Deviation Disc (0.8mm) • For T-Skew and R-Skew Adjustment Not spare parts Fig.5. L-Wrench(3mm) Not spare parts Fig.6. RCA Jack Fig.7. Connecting Method 2. Install Process 1. Connect Fig. 1, 2, 3 as Fig. 7. 2. Plug out the Power cord of DVD set. 3. Connect FFC Cable(Fig.
DECK MECHANISM ADJUSTMENT How to upgrade by upgrade DISC. (*DV4200UPD) Connect the DVD Player to [TV] and Operate by using [Remote Controller] 1. Reading upgrade disc CURRENT PICK UP POSITION ERROR RATE SIZE SECTOR : 200145 0045 0065 AVERAGE ERROR RATE ERROR RATE (HEXADEAMAL) Fig.11. Adjusting Screen Display 3. Adjustment Procedure 1. Insert Disc(Only Open/Close Key Pressing) 2. Wait Until the Sector Display is about 200,000 (Fig.11) 3.
EXPLODED VIEW 1. Deck Mechanism Exploded View and Parts list 001 429 002 A01 016 003 430 004 A03 429 009 430 430 432 008 A02 012 018 026 430 020 POS. NO. 430 017 014 013 011 015 431 VERS. COLOR PART NO.
