MODEL 7924 Rev. A 7-7-14 MAN 430088 MODEL 7920 430088 Mantis 2-Cycle Tiller Color Cover.
Welcome to the World of Mantis Gardening Here’s your new MANTIS Tiller . . . the lightweight wonder that’s Changing the Way Americans Garden.® ATTENTION MANTIS PRODUCT OWNERS! Unlike big tillers, your MANTIS Tiller weighs only 20 lbs. (Model 7920) and 22.5 Get maintenance tips for your Mantis lbs. (Model 7924). So it lifts easily, handles smoothly, tills and weeds precisely. product on our web site And, unlike other small tillers, it features serpentine tines that churn soil to ten at www.mantis.
Safety Rules & Warnings You will notice throughout this Operator’s Manual Safety Rules and Important Notes. Make sure you understand and obey these warnings for your own protection. I. SPECIAL SAFETY INFORMATION Attention: This symbol points out our important safety instructions. When you see this symbol, heed it’s warning!! Stay alert!! To reduce the potential for accidents, comply with the safety instructions in this manual.
If the tiller is used improperly or safety precautions are not followed, the users risk serious injury to themselves and others. Read and understand this manual before attempting to operate this tiller. Operation of this equipment may create sparks that can start fires around dry vegetation. A spark arrestor is installed. The operator should contact local fire agencies for laws or regulations relating to fire prevention requirements. IV. WARNINGS - DOS Read and understand the owner’s manual.
Safety Rules & Warnings V. WARNINGS - DON’TS Don’t use tiller with one hand. Keep both hands on handles with fingers and thumbs encircling the handles, while tines are moving, and engine is running. Don’t run with the machine, walk. Don’t work on excessively steep slopes. Don’t attempt to clear tines while they are moving. Never try to remove jammed material before switching the engine off and making sure the tines have stopped completely.
Assembly Picture of Model 7924 T21B T20 Picture of Model 7920 T46 T21A T40 T39 Improper assembly of this tiller can result in serious injury. Make sure to follow all instructions carefully. If you have any questions, contact our factory at 1-800-366-6268 or an authorized Mantis dealer. Bag Contents T20 T12 T46 T9 T41 T4 T11 T42 T15 T2 T1 T14 T3 T41 T15 T9 T42 T13 T11 T7 T14 T12 T10 Key Qty.
Assembly LET’S BEGIN • With the box upright, open the box and remove the tine box and the loose parts that are at the top of the tiller box. Do not remove any other parts in the box. • Lay the box on one side and open the bottom flaps. • Return the box to an upright position (as shown) and pull the box straight up. • Leave the engine and throttle handle in the cradle to assist in the assembly. • Lay everything out so you can easily identify the parts (see parts image and list on page 6).
Assembly (Continued) UPPER HANDLE ASSEMBLY 7a • Lightly squeeze the lower handles (T3) toward one another so that they line up with the two smaller holes on the carrying handle (T10). Then slide the carrying handle over and down the lower handles. It will rest about four to six inches above the fender. • Gently pull the lower handles out to their original position. 8 9 • Lift the upper handle until it lines up with the lower handle. • Insert carriage bold (T42) from outside in.
Assembly TINE ASSEMBLY (Continued) 4 5 • Attach the Tine so that the circular hole slides onto the axle first. 6 • When the axle protrudes from the other side it will line up perfectly with the “D” shaped hole. KICKSTAND ASSEMBLY (MODEL 7924 ONLY) 1 (Continued) 2 • Slide a retaining pin (T41) through the hole in the axle to secure the Tine. • Repeat steps for the other side. 3 • Position the kickstand brace just above the bend of the lower handles.
2-Cycle Tiller Fueling 2-CYCLE TILLER FUELING MIXING FUEL Use a mixture of 50 parts unleaded regular gasoline and 1 part two-stroke MANTIS oil (50:1.) Use branded 89 octane (R+M+2) unleaded gasoline (maximum 10% ethanol, or 15% MTBE, no methyl alcohol.) 2.6 oz. bottle of Mantis 50:1 2-cycle engine oil Here’s how to mix the oil with the gas: 1. Pour 1/2 of the gasoline into a safe container. Do not mix the fuel and oil in the engine fuel tank. 2. Add 2.
2-Cycle Tiller Starting 2-CYCLE TILLER STARTING 1. Fill the fuel tank with the proper oil/gasoline mixture. (See previous section.) 2. Hand tighten the gasoline cap just until it’s snug. 3. Place the O/I switch into the I “start/on” position. (Picture 1) 4. Pull the choke button all the way out, to completely close the choke. (Picture 2) 5. Locate the purge bulb on the upper right of the engine, in front of the fuel tank. (See Picture 3) It sends fuel into the carburetor, for easy starting.
2-Cycle Tiller (Continued) WHAT TOStarting DO JUST IN CASE WHAT TO DO JUST IN CASE you follow the normal the stop If youIffollow the normal starting procedure, is youinshould haveposition, no problem starting your disconnect starting procedure, youdoshould tiller. But, just in case you have problems, here’s whatspark to do. plug wire and have no problem starting your remove plug. Use a paper towel Make sure the O/I switch is on “I” (start).
2-Cycle Tiller Operation If engine does not stop when switch is put in the stop position, release the throttle, allow engine to idle. Put the tiller down, and slide the choke lever to the cold start (closed) position. Have product serviced before using. A SPECIAL FEATURE (With the idle set properly and the engine running) Even when the engine is running, the tines won’t turn unless you squeeze the throttle trigger on the handlebars. When you release the throttle trigger, the tines will stop.
2-Cycle Tiller Operation (Continued) If your tines get jammed or entangled, shut off the engine at once. Remove the obstruction while the engine is off. Never try to remove an obstruction while the engine is running. Serious injury can result. The operator of this tiller is responsible for accidents or hazards occurring to himself, other people or their property.
2-Cycle Tiller Transportation & Storage 2-CYCLE TILLER TRANSPORTATION Transporting your Tiller is easy. It’s light enough and easy to carry using the carrying handle as seen in Figure 1. Or, with it running, you can walk it by gently squeezing the throttle until it moves at a comfortable pace. Your tiller is easily transported in the back of a car or truck. Be sure to empty the fuel tank (This is crucial)! Then stow your tiller in the trunk of your car or truck.
2-Cycle Tiller Maintenance HOW TO CHECK, CLEAN AND CHANGE THE AIR FILTER 1. Loosen the wing nut on the side of the air-cleaner cover. (Picture 1) 2. Take off the cover. Make sure to clear the choke button. 3. The air filter is the pad on the inside of the air-cleaner cover. Check whether it is soiled or moist. 4. If the air filter needs cleaning or no longer fits properly, remove it. Just lift an edge carefully and “peel” it out. (Picture 2) 5. Use a brush to remove debris from the pad. 6.
2-Cycle Tiller Maintenance Then stop the engine after it reaches operating temperature. ! WARNING • DANGER ! Now, turn the RED, high-speed screw counter-clockwise all the way to stop… Then turn the WHITE, low speed screw halfway between the counter-clockwise and clockwise stop positions.
2-Cycle Tiller Maintenance HOW TO RESEAT THE FLANGE At some point, you may find that the tines won’t turn when you press the throttle. This may mean the engine isn’t sitting all the way down on the worm gear housing. Perhaps you’ve been using your Tiller for several years. Or perhaps you’ve removed the engine for use with our hedge trimmer attachment, then replaced it. In either case, the flange bolt may have come loose and lifted the engine up.
Troubleshooting Problem Cause Remedy 1. T ines don’t turn when throttle is depressed • Engine is not seated properly on the gear housing. • Re-install engine following the instructions on page 18 “How to reseat the flange”. 2. Engine fails to start • O/I switch is in “O” position. • No fuel in tank. • Fuel strainer clogged. • Fuel line clogged. • Spark plug shorted or fouled.
2-Cycle Tiller Assembly T15 T4 T14 T19 MODEL NO. 7924 T1 MODEL NO. 7920 T2 T14 T21B T21A T15 T9 T42 T10 T12 T43 T9 T13 T12 T42 T3 T22* T8 T18 T7 T14 T11 T7 T16 T20 T17 MODEL NO. 7924 ONLY T44 T50 T41 T34 T36 T37 T36 T23 T38 T33 T35 T38 T39 T49 T27 T28 T41 37 T35 T29 T30 T45 T40 20 430088 Mantis 2-Cycle Tiller Color Cover.
430088 Mantis 2-Cycle Tiller Color Cover.indd 21 Contact us at www.mantis.com T31 T37 T38 Handle Clamp M6 Jam Nut Throttle Clip Carry Handle Bolt 1/4-20 X 3” Knob, Two Prongs, Female Acorn Nut 1/4-20 Two-Way Lock Nut 1/4-20 X 1.125 Hex Head Cap Screw Bolt 1/4-20 X 3/8” Long Mantis Logo Label M6 Internal Lock Washer Engine Label Fender Guard Engine Assembly SV-5C/2 (Model No. 7920) Engine Assembly SV-5CI/2 (Model No.
Table of Contents Part Number Index SV-5C/2 Engine Carburetor -- C1U-K82 Key A1 Parts Assemblies Model 7920 SV-5C/2 Engine A2 Model 7924 A3 SV-5CI/2 Engine Carburetor - C1U-K82 A4 Explosion A A24 A35 A25 A36 A22 A34 A26 A27 A6 A28 A29 A30 A17 A5 A23 23 A16 A8 A15 A7 A31 A10 A14 A9 Table of Contents Part Number Index SV-5C/2 Engine A13 Intake A12 A32 A37 A11 A33 A38 A18 A21 A19 A20 Air Cleaner Explosion B Table of Contents B17 SV-5C/2 Engine 99922200869 B14 B15 B13
Table of Contents Part Number Index SV-5C/2 Engine Table of Contents Clutch Case, Clutch Part Number Index Engine Cover, Fancase, Starter Parts Assemblies Model 7920 SV-5C/2 Engine Model 7924 SV-5CI/2 Engine D17 Engine Cover, Fancase, Clutch Case & Clutch D16 D14 Explosion D D15 D13 D12 D11 D10 Key D1 D2 D3 D4 D5 D6 D7 D8 D9 D10 D11 D12 D13 D14 D15 D16 D17 Part No.
Table of Contents Engine Cover, Fancase, Starter Parts Assemblies Model 7920 SV-5C/2 Engine Model 7924 Part Number Index SV-5C/2 Engine Model 7924 F19 Key F1 F2 F3 F4 F5 F6 F7 F8 F9 F10 F11 F12 F13 F14 F15 F16 F17 F18 F19 Model 7924 SV-5CI/2 Engine Engine Starter Model 7920 F28Part Explosion Table F ofof Contents Table Contents Part Number Number Index Index Table of Contents SV-5C/2 Engine Engine SV-5C/2 SV-5C/2 Engine F2 Part Number Index Engine F3Cover, Fancase, Starter Engine Cover, Cove
ECHO INCORPORATED EMISSION CONTROL WARRANTY STATEMENT FOR ECHO AND SHINDAIWA BRANDS The Environmental Protection Agency (EPA) and the California Air Resources Board (C.A.R.B.) and ECHO Incorporated (ECHO Inc.) are pleased to explain the emission control system warranty on your 2010 and later equipment/small off-road engine (SORE). New equipment/SORE must be designed, built and equipped to meet stringent EPA and C.A.R.B. anti-smog standards. ECHO Inc.
EPA PHASE 2 / CALIFORNIA TIER III EMISSION CONTROL WARRANTY STATEMENT YOUR RIGHTS AND OBLIGATIONS The Environmental Protection Agency (EPA) and the California Air Resources Board (C.A.R.B.) and The Equipment Manufacturer are pleased to explain the emission control system warranty on your EPA Phase 2 / C.A.R.B. Tier III model year 2005 and later small off road engine (SOREs). New small off road engines must be designed, built and equipped to meet stringent EPA and C.A.R.B. anti-smog standards.
Contact us at www.mantis.com 430088 Mantis 2-Cycle Tiller Color Cover.
LIMITED WARRANTY MANTIS extends this limited warranty against defects in material and workmanship for a period of five (5) years under normal usage for residential purposes and two (2) years under normal usage for commercial purposes, from the date of purchase by the original purchaser. MANTIS will repair or replace, at its option, any part or parts of the product found to be defective in material or workmanship during the warranty period.