000010415 - 13/03/2019 Assembly Guide Model: 8GMC1 / 8GMC2 / 8GMC3 / 8GMC4 Nightstand Stuck? Questions? We are here to help. 1-888-230-2225 help@manhattancomfort.
In order to ease the assembly, you should separate and identify the parts first Do not place the parts directly onto the floor. Use a cardboard sheet or a mat to place the parts, during the separation and assembly. IMPORTANT In order to avoid severe or even fatal injuries, follow the instructions carefully.
L W 22 LB s P3 H P1 P5 ASSEMBLED PRODUCT: H: 20.07'' W:13.77'' L:13.77'' P4 22 LB s P2 P6 Lbs Maximum weight supported distributed P7 P8 Hardware list F1 F2 F3 F4 1000008297 1000008616 1000009033 1000000281 - WHITE 1000007352 - BLACK 1000010221 - BLUE Qty. 2 Qty. 2 Qty. 1 Qty. 2 F5 F6 F7 F8 1000010136 1000008285 3000009645 - WHITE 3000009643 - BLACK 3000009649 - BLUE 3000009647 - GREY 1000008285 Qty. 1 Qty. 2 Qty. 1 Qty.
1 - Identify the parts as figure below: P7 with hole and P8 without hole. P8 P7 1 - Attach the P8 part on the P1 and P2 parts in the indicated direction. 2 - Then attachthe P7 part on the P1 and P2 parts.
1 - Check the alignment of the holes on the fitted parts. 2 - The hole in the horizontal bar of part P7, should be up. P7 01 02 1 - With the F3 end, smash the safety grappel, locking the P7 and P8 part to the P1 and P2 part.
1 - Identify the cutout on the top end of the P5 part. 2 - Attach the P5 part on the P1, P2 and P8 parts. 3- Slide part P5 to support on parts P1 and P2. P1 P2 P5 P5 P8 01 04 1 - With the end of F3, smash the safety claw, locking part P5 to part P1 and P2.
1 - Attach the joint of the front of the P4 part under the P7 part. 2 - Lower the P4 part as indicated. P4 P7 01 06 1 - Check all the fittings before moving forward.
1 - Attach the P3 part on the parts P1 and P2. P3 1x P3 2 - Pull the front of the P3 part.
1 - With the end of F3, smash the fety claw, locking part P3 to part P5. 2x F3 2x 2x 01 09 2x 1 - Lay the cabinet against the wall and mark the hole.
1 - Drill the wall on the marked point, using a ½” drill bit. ½” 01 11 1 - Insert the metal part of the bushing into the hole until it overcomes the wall.
1 - Pull the bushing driving it against the wall and then push the plastic ring until it leans close to the wall Plastic ring WALL 2 - Break the bushing's rods WALL 2 1 WALL 01 13 WALL
1 - Insert the screw F2 into the hole of part P5. 2 - Turn screw F2 with part F3 clockwise. 2x 3 - Press part F4 against the heads of the F2 screws. 2x F4 F2 F3 01 14 F2 F3 F4 2X 1X 2X 1 - Attach the F5 into the P7 part.
1 - Attach the F7 handle to the door P7 as indicated below F7 F7 CK ! I CL F7 P6 1X 01 1616 1 - Attach the F6 into the P6 holes.
1 - Attach part P6 to the bottom of the cabinet through part F5 2 - Finish engaging part P6 through the pivoting wrench as shown below. P6 F5 01 18 1 - Glue F8 to part P6 in the indicated area.
TAKING GOOD CARE OF YOUR CABINET Cleaning and caring instructions: - Avoid dragging objects on top of the cabinet. They might scratch the finishing. - Only non-abrasive natural chemical products are recommended to clean your cabinet. Simply wipe the cabinet down with a wet cloth to remove the cleaning product excess. - Never clean the cabinet with scouring powders, steel scrubber pads or any other product which can scratch its surface. - Chemical products are not recommended.
WARRANTS TERMS This product has the guarantee for a period of twelve (12) months, this limited warranty is effective from the date of the original consumer purchase. Proof of original purchase date is required to obtain service or replacement under this limited warranty. Once the defect of manufacture has been verified, the consumer should contact the store where he purchased the product. In the warranty period, any defective parts will be replaced free of charge by another of the same line and model.