000010416 - 13/03/2019 Assembly Guide Model: 11GMC1 / 11GMC2 / 11GMC3 / 11GMC4 Double Cabinet Stuck? Questions? We are here to help. 1-888-230-2225 help@manhattancomfort.
In order to ease the assembly, you should separate and identify the parts first Do not place the parts directly onto the floor. Use a cardboard sheet or a mat to place the parts, during the separation and assembly. IMPORTANT In order to avoid severe or even fatal injuries, follow the instructions carefully.
L W P3 26 Lbs H P6 P5 26 ASSEMBLED PRODUCT: H: 29.92'' W:27.55'' L:13.77'' Lbs P1 P7 26 Lbs P4 P9 P2 Lbs Maximum weight supported distributed P10 P8 P11 Hardware list F1 F2 F3 F4 1000008297 1000008616 1000009033 1000000281 - WHITE 1000007352 - BLACK 1000010221 - BLUE Qty. 2 Qty. 2 Qty. 1 Qty. 2 F5 F6 F7 F8 1000010136 1000008285 3000009645 - WHITE 3000009643 - BLACK 3000009649 - BLUE 3000009647 - GREY 1000008285 Qty. 2 Qty. 4 Qty. 2 Qty.
1 - Identify the parts as figure below: P10 with hole and P11 without hole. P11 P10 1 - Attach the P11 part on the P1 and P2 parts in the indicated direction. 2 - Then attachthe P10 part on the P1 and P2 parts.
1 - Check the alignment of the holes on the fitted parts. 2 - The hole in the horizontal bar of part P10, should be up. P2 P1 P10 01 02 4x 1 - With the end of F3, smash the safety claw, locking part P10 and P11 to part P1 and P2.
1- Identify the cutout on the top end of the P7 part. P7 01 04 1 - Attach the P7 part on the P1, P2 and P11 parts. 2 - Slide part P7 to support on parts P1 and P2..
1 - With the end of F3, smash the safety claw, locking part P7 to part P1 and P2. 2x F3 P7 01 06 1 - Attach the joint of the front of the P4 part under the P7 part. 2 - Lower the P4 part as indicated.
1 - Check all the fittings before moving forward. P4 01 08 1 - Attach the P6 part with both cutouts facing up, on parts P1 and P2. 2 - Attach the P6 part onto the P7 part.
1 - With the end of F3, smash the safety claw, locking part P7 to part P1, P2 and P7.
1 - Attach the P3 part on the parts P1 and P2. P3 2x P3 2 - Pull the front of the P3 part.
1 - With the end of F3, smash the safety claw, locking part P6 to part P3. P3 2x F3 2x 2x 01 12 1- Slightly turn the P5 part and place it inside the cabinet, as indicated. 2- Check all the fittings before continuing.
IMPORTANT: CABINET MUST BE ATTACHED TO THE WALL 1 - Lay the cabinet against the wall and mark the hole. 2x 01 14 1 - Drill the wall on the marked point, using a ½” drill bit. 2 - Insert the metal part of the bushing into the hole until it overcomes the wall.
3 - Pull the bushing driving it against the wall and then push the plastic ring until it leans close to the wall WALL Plastic ring 4 - Break the bushing's rods 1 WALL WALL 2 WALL 01 15
1 - Insert the screw F2 into the hole of part P5. 2x 2 - Turn screw F2 with part F3 clockwise. 3 - Press part F4 against the heads of the F2 screws. 4 - Attach the F5 into the P10 part.
1 - Attach the F6 into the P8 and P9 holes. 2 - Glue F8 to part P8 in the indicated area.. F8 2x F6 P9 2x P8 F6 F6 F8 4X 1X 01 18 1 - Attach part P8 to the right side of the enclosure on parts F5 and P4. 2 - Attach part P9 to the left side of the enclosure on parts F5 and P4.
TAKING GOOD CARE OF YOUR CABINET Cleaning and caring instructions: - Avoid dragging objects on top of the cabinet. They might scratch the finishing. - Only non-abrasive natural chemical products are recommended to clean your cabinet. Simply wipe the cabinet down with a wet cloth to remove the cleaning product excess. - Never clean the cabinet with scouring powders, steel scrubber pads or any other product which can scratch its surface. - Chemical products are not recommended.
