User's Manual

ManualsBrandsMandolyn Electronic Technology ManualsElectronicsWeather Station Receiver

Press and hold MODE for 3 seconds to Clock Setting mode

Press MODE again to Month/Date setting mode

Press HOUR/+/MAX to set month

Press MINUTE/-/MIN to set date

Press MODE to enter Year setting

Press HOUR/+/MAX or MINUTE/-/MIN to adjust Year

Weekday is automatically determined from the year/month/day setting

MONTH & DATE, YEAR SETTING

P.6

WS928+WT440H

Wireless Weather Station

KNOW YOUR PRODUCT

button placement

Minute/-/Min: shows minimum temperature; adjusts

clock, alarm, date & year and temperature alarm values

Snooze/Mode: scrolls through Clock 1 & 2, Alarm 1 & 2,

Date & Year, and Temperature Alarm(high & low) mode;

snooze for alarm

LCD display

ON/OFF /(C/F): toggles between C and F, 12 and 24 hour

format, Alarm 1 & 2 on and off; disables (resets) high &

low temperature alarms

Channel: scrolls through remote channels Outside,

Outside 2 and Outside 3); scrolls through local and remote

channels (Outside, Outside 2 and Outside 3) in (high & low)

temperature alarm mode; activate learn process

Hour/+/Max: shows maximum temperature; adjusts

clock, alarm, date & year and temperature alarm values

P.1

P.5 P.7

P.4

P.8

Inside temperature /

humidity trend symbol

P.2

or will flash, and the sound volume

will gradually from low to high

Press SNOOZE to snooze the alarm for 5 minutes,

after that the alarm will sound again

Press ANY other key will shut off the alarm.

Without interruption, the alarm will shut off

automatically after one minute

ALARM SETTING

P.3

SET: enter to House code and Channel setting mode

C/F: change between °C or °F,

change channel and house code

Battery compartment

LCD display

Wall mount holder &

table stand

Scroll to Alarm1 mode (Alarm2 mode) using MODE

Press HOUR to set hour

Press MINUTE to set minute

Press ON/OFF/(C/F) to set alarm on or off

When the alarm is set ON, the bell

symbol / will appear

Press and hold MODE for 3 seconds to enter the clock setting mode

(the CLOCK 1 symbol appears and the time will flash)

Press HOUR to set the hour and MINUTE to set the minute;

Press ON/OFF(C/F) during clock setting, to change between

12 and 24 hour display.

Do not press any key for 1 minute to finish clock setting

Scroll to Clock 2 mode using MODE

Press + or - key to change the time

iii

OUT

WS928 receiver

Inside temperature /

humidity reading

Outside temperature

reading

Outside humidity reading

Outside temperature

trend symbol

Outside humidity trend

Pressure trend symbol

Pressure reading

Moon phase

Comfort level icon

Weather forecast

symbols

Month/Day, Year

Alarm clock

Clock

Weekday

Temperature/

pressure historical

bar graph

Clock 1 Setting

Clock 2 Setting

Alarm 1and Alarm 2 setting

When alarm sounds

The colon symbol " " appears if

date value is 2-digit (e.g. 13, 26...)

MANUAL CLOCK SETTING

READ THIS BEFORE YOU BEGIN

Insert batteries into the remote transmitter(s) first, and then the receiver.

For the best operation,

Although remote transmitters are weather resistant, it is recommended to place it away from direct

sunlight, rain or snow. This will help to make condition readings more accurate.

Place the receiver and remote transmitter(s) close together. This will ensure that the receiver

synchronizes with remote transmitter(s).

Place the remote transmitter(s) outdoors within an effective transmission range.

The transmission range can be affected by the dense walls or electronic interference

in between the receiver and transmitter. Try various set-ups for best results.

3 5 7

GETTING STARTED

Remove battery cover and insert 2 AA size batteries. Insert

between terminals observing proper polarity then replace cover.

Remove battery cover and insert 2 AA size batteries to start setup.

The HOUSE CODE will flash for 8 seconds

Select the HOUSE CODE by pressing C/F

Select CHANNEL(1-4) by pressing C/F. This number will be confirmed upon pressing

the SET button, or if no key is pressed for 10 seconds. If only one transmitter is available,

it is recommended to leave the CHANNEL be "01”

The range of House Codes are from "01" to "15". Make sure all transmitters

in your system are set to the same House Code.

Humidity & Temperature will display

Select °C or °F of Temperature by pressing C/F and pressing SET. Once setup of remote

transmitter is completed, it will start transmitting at one minute intervals

STEP 1 : setting the remote transmitters

* Use a different house code if your weather station detects

other signals from neighboring sources

* Factory default: house code = 01 and channel = 01

STEP 2 : setting the receiver

SYNCHRONIZATION

Automatic Learn Function:

Manual-Learn Function (Searching for Remote Signals):

The Learn function begins automatically and runs for

3 minutes when receiver batteries are first installed.

Press and hold Channel for 3 seconds in clock display mode

If a new transmitter is added or if signal is lost (outdoor display blinking),

the learn function must be executed again.

Within these 3 minutes, the receiver will beep and display

the temperature & humidity signals from transmitter(s).

A beep sound indicates that learn function has started

The Outside the symbol will flash and unit

will beep as each remote sensor is detected

Temperature & humidity readings of the

remote sensor will display on the receiver.

If the signals are not received within this 3 minutes, the outside temperature and

humidity will show " ". If this is the case, bring the units closer togther or

try a different location. Then restart the auto learning function by temporarily

removing the batteries from receiver.

Moon Phase Display

MOON PHASE

The moon phase is automatically updated

according to the year/month/day.

New Moon

Young Crescent

First Quarter

Waxing Gibbous

Full Moon

Waning Gibbous

Last Quarter

Old Crescent

WT440H

Transmitter

OWNERS MANU

SET

C/F

AA 1.5V

SET

C/F

AA 1.5 V

SET

C/F

AA 1.5V

TEMPERATURE / PRESSURE

HISTORICAL BAR GRAPH

Note: If you have multiple transmitters

press CHANNEL to scroll through below

sequence:

The bar graph lets you see the pressure trend over a period of 24 hours.

(automatically resets at midnight). The bar graph will show the Pressure

Trend (Default), or the Local or Remote

Temperature by pressing ON/OFF(C/F)

in Clock1 mode.

The sequence is:

Pressure Trend

Inside Temperature Trend

Outside Temperature Trend

( , , )

Pressure Trend

Inside Temperature Trend

Outside Temperature Trend

Channel 1

Channel 2

Channel 3

Summary of content (2 pages)

PAGE 1
3 Minute/-/Min: shows mi nimum temperature; adjusts clock, alarm, date & year and temperature alarm values 4 ON /OF F /(C/ F): toggles betwe en C and forma t, Alarm 1 & 2 on and off; disables (resets) high & low temp erature alarms 4 5 F, 12 and 24 hour Inside temperature / humidity reading Weather forecast symbols Month/Day, Year Outside temperature reading Alarm clock Outside temperature trend symbol Outside humidity reading Clock Weekday Outside humidity trend Pressure reading Temperature/ pr
PAGE 2
TEMPERATURE & HUMIDITY DISPLAY Check Inside Temperature & Humidity After inserting the batteries, the inside temperature and humidity readings will display alternately on the receiver. * * If the outside temperature falls below -30°C or the outside relative humidity falls below 15%, the symbol "LO" will appear on the screen respectively; If the humidity rises above 95%, the symbol "HI" will appear on the screen. Both events are quite normal and do not mean that your weather station is defective.