User's Manual

ManualsBrandsMandolyn Electronic Technology ManualsElectronicsWireless Doorbell

Wireless doorbell

Operating instructions and guarantee

About these instructions

Warning

This product is equipped with safety features.

All the same, read the safety instructions carefully and use this appliance only as

described in these instructions to avoid accidental injury or damage.

Keep these instructions for future reference.

If you pass on this article to someone else, remember to include these instructions.

Intended use

The wireless doorbell is designed for wireless transmission of bell signals. The doorbell

signal can be displayed as an optical and/ or as an acoustic signal.

Hazards to children

z Batteries can be highly dangerous if swallowed. Therefore, keep batteries and the

doorbell out of the reach of small children. If a battery has been swallowed, seek

medical assistance immediately.

z Keep packaging material away from children. There is a risk of suffocation!

Electrical hazards

z Ensure that the locations where you wish to install the devices are free of power supply

lines, water lines and service pipes.

Other potential risks of injury

z Batteries must not be charged or re-activated by any other means, taken apart, thrown

into fire or short-circuited.

Caution – damage to the doorbell

z Remove the batteries from the doorbell when they are empty or if you are not planning

to use the device for a prolonged period of time. This will avoid damage that can be

caused by leakage.

z Always replace batteries in the doorbell (receiver).

z Do not use batteries of different types, brands or capacities.

z Alkaline batteries are recommended.

z Replace the batteries when the chime sounds are distorted.

z Never immerse the device in water.

z Never clean the device with abrasive or caustic cleaners.

z Never expose the device to snow, impact, vibration, dust, extreme temperatures or

high humidity. Install the bell push ensuring that it is not exposed to rain or direct

sunlight.

z Do not make any modifications to the device. Repairs must only be carried out by a

specialized workshop.

z Before installing, check whether you have the correct mounting material for your wall.

Summary of content (7 pages)

PAGE 1
Wireless doorbell Operating instructions and guarantee About these instructions Warning This product is equipped with safety features. All the same, read the safety instructions carefully and use this appliance only as described in these instructions to avoid accidental injury or damage. Keep these instructions for future reference. If you pass on this article to someone else, remember to include these instructions. Intended use The wireless doorbell is designed for wireless transmission of bell signals.
PAGE 2
z Do not install the bell push (transmitter) or doorbell (receiver) in direct vicinity of other electronic devices. This could lead to interference in either the wireless doorbell or other electronic devices. z Do not use several wireless doorbells in immediate vicinity of one another. This could lead to interference.
PAGE 3
) Carefully close the battery compartment again. Bell push 1) Open the battery compartment on the back of the bell push. 2) Insert 23A/12V battery supplied with the system, ensuring correct battery polarity (+/-). Leave the compartment open to be able to synchronize the radio frequency code in the next step. Synchronization (LEARN procedure) This Doorbell is designed with the technology of Intelligent Code setting and Learning function.
PAGE 4
Choosing the signal Note: Be sure to set the signal before mounting the bell push to the wall. The signal selection switch allows you to set the following signals: Chime only Signal indicator blinks and chime is switched to silent Chime and blinking signal indicator Low Battery Indication Transmitter: z If the transmitter is out of battery, the LED will be ON in RED color for several seconds and the RED LED is ON when the Doorbell button is pressed. z Then please change new battery into the transmitter.
PAGE 5
1) Remove the battery compartment lid from the bell push. 2) Mark the holes on the wall. Use the mounting holes on the battery compartment lid as a guide. 3) Drill two holes (Ø 6 mm). Note: Please note that the drill can ‘drift’ in the hole, quickly causing the inside diameter of the hole to become larger than desired. You should use a smaller drill (Ø 5 mm) to make a preliminary hole before drilling the final holes.
PAGE 6
and doorbell push (transmitter) is too long. The range of the radio signal transmission can be significantly decreased by thick walls and/ or ceilings. Batteries are weak or empty. Replace battery. Doorbell ring is quieter than normal or Check the set signal and reset it if sounds distorted. necessary. Doorbell ring sounds even when the bell Have the LEARN procedure being done? push has not been passed.
PAGE 7
user is encouraged to try to correct the interference by one or more of the following measures: • • • • Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This Class B digital apparatus complies with Canadian ICES-003.