Programming Instructions

ManualsBrandsMANARAS/OPERA ManualsElectronicsRemote Control

Rolling Code Transmitters - Series "100"

Specifications and Programming Instructions

Commercial Sequence or SBC Programming (Optional)

Modes Functions

Programming

(On operator's ECB)

Commercial

Sequence -

1-Button

OPEN / CLOSE  Button

Door is CLOSED:

- Click Button  Door OPENS FULLY

During UPWARD Travel:

- Click Button  Nothing happens

Door is OPENED:

- Click Button  Door CLOSES FULLY

During DOWNWARD Travel:

- Click Button  Door reverses and OPENS FULLY

Door is STOPPED:

- Not possible in this mode. Door is either FULLY

OPENED or FULLY CLOSED.

Standard default mode.

1.Door is in fully CLOSED posi

tion.

2.On ECB, verify if the close limit

switch is activated (CLOSE LED is

ON).

3.On ECB, set select switch on

9 = SBC.

4.On ECB, press “STOP” button.

5.On ECB, select run mode

(1, 4, or 5).

Single Button

Control (SBC)

Available with the

Electronic Control

Board (ECB) only.

Alternating

Sequence

OPEN / STOP / CLOSE  Button

Door is CLOSED:

- Click Button  Door OPENS

During UPWARD Travel:

- Click Button  Door STOPS

Door is STOPPED:

- Click Button  Door CLOSES

Dur

ing DOWNWARD Travel:

- Click Button  Door STOPS

Door is STOPPED:

- Click Button  Door OPENS

Note: If the door is STOPPED for more than 2 minutes,

the next movement will be UPWARD regardless of the

previous movement.

1.Door is in fully CLOSED position.

2.On ECB, verify if the close limit

switch is activated (CLOSE LED is

ON).

3.On ECB, set select switch on

9 = SBC.

4.On ECB, press “OPEN” button.

5.On ECB, select run mode

(1, 4, or 5).

For further i

nformation, please consult the operator's Installation & Instruction Manual or contact our Technical

Support Department at

1-800-361-2260

www.manaras.com

4 TN1054 REV 0 - 2019/07/25

Rolling Code Transmitters - Series "100"

Specifications and Programming Instructions

Transmitter Programming: RADIOEM101, RADIOEM102, RADIOEM103, RADIOEM104

The Opera Brand Transmitters can be used as either a 1-Door x 3-Button Transmitter or as a Multiple-Door

Transmitter (Commercial Sequence or SBC). Commercial Sequence or SBC settings depend on the operator

programming settings. The Transmitters can be re-programmed as needs change.

Transmitter Modes and Functions Transmitter Programming

RADIOEM101

1-Door

1-Button Transmitter

(1)

1.OPEN / STOP / CLOSE  Only Button

No initial programming is required.

The Transmitters are ready to be matched to the

Receiver of your choice, refer to section Transmitter

to Operator Matching (Pairing), p. 3.

RADIOEM104

4-Door

4 x 1-Button Transmitter

(1)

1.DOOR #1  Top Left Button

2.DOOR #2  Top Right Button

3.DOOR #3  Bottom Left Button

4.DOOR #4  Bottom Right Button

(1)

Each button acts separately as a 1-Button Transmitter.

Commercial Sequence or SBC Programming depends on the Operator Settings, please refer

to the Commercial Sequence or SBC Programming instructions, p. 4).

RADIOEM102

Mini Key Chain

1-Door

3-Button Transmitter

(Factory default for RADIOEM103SD)

1.OPEN  Top Button

2.CLOSE  Middle Button

3.STOP  Bottom Button

1.Press and HOLD Buttons

 and  for 5 sec.

The RED LED will BLINK.

You have 15 sec. to complete the configuration or

you will need to restart.

2.Release Buttons

 and .

3.Press Button

.

4.The RED LED will stop blinking.

Programming is now complete.

RADIOEM103

Single Door (SD) /

Multiple Door

(MD)

3-Door

3 x 1-Button Transmitter

(1)

(Factory default for RADIOEM102 &

RADIOEM103MD)

1.DOOR #1  Top Button

2.DOOR #2  Middle Button

3.DOOR #3  Bottom Button

1.Press and HOLD Buttons

 and  for 5 sec.

The RED LED will BLINK.

You have 15 sec. to complete the configuration or

you will need to restart.

2.Release Buttons

 and .

3.Press Button

.

4.The RED LED will stop blinking.

Programming is now complete.

(1)

Each button acts separately as a 1-Button Transmitter.

Commercial Sequence or SBC Programming depends on the Operator Settings, please refer

to the Commercial Sequence or SBC Programming instructions, p. 4).

1-800-361-2260

www.manaras.com

1 TN1054 REV 0 - 2019/07/25

Summary of content (4 pages)

PAGE 1
Rolling Code Transmitters - Series "100" Rolling Code Transmitters - Series "100" Specifications and Programming Instructions Specifications and Programming Instructions Transmitter Programming: RADIOEM101, RADIOEM102, RADIOEM103, RADIOEM104 Commercial Sequence or SBC Programming (Optional) Modes Programming (On operator's ECB) Functions OPEN / CLOSE Button The Opera Brand Transmitters can be used as either a 1-Door x 3-Button Transmitter or as a Multiple-Door Transmitter (Commercial Sequence or SBC
PAGE 2
Rolling Code Transmitters - Series "100" Rolling Code Transmitters - Series "100" Specifications and Programming Instructions Specifications and Programming Instructions Transmitter Programming: RADIOEM144 The RADIOEM144 Rolling Code Transmitter can be used to control up to 144 doors with Open / Close / Stop function. Two rotary dials (Letters: A to L) and (Numbers: 1 to 12) permit for a proper door selection . The Transmitter can be reprogrammed as needs change.
PAGE 3
Commandes radio "code aléatoire" - Série "100" Commandes radio "code aléatoire" - Série "100" Spécifications et Instructions de programmation Spécifications et Instructions de programmation Programmation : Séquence Commercial ou CBS (Optionnel) Modes OUVRIR / FERMER Séquence commercial 1-Bouton Contrôle à bouton simple (CBS) Disponible seulement avec le circuit de contrôle électronique (CCE).
PAGE 4
Commandes radio "code aléatoire" - Série "100" Commandes radio "code aléatoire" - Série "100" Spécifications et Instructions de programmation Spécifications et Instructions de programmation Options de programmation de l'émetteur: RADIOEM144 L'émetteur RADIOEM144 avec la technologie code aléatoire et à 3-boutons Ouvrir / Fermer / Arrêt peut opérer jusqu'à 144 portes. Deux cadrans rotatifs (Lettres: A à L et Numéros: 1 à 12) permettent de sélectionner la porte appropriée.