INSTRUCTION MANUAL MANUAL DE INSTRUCCIONES Cordless Recipro Saw Sierra Recíproca Inalámbrica XRJ05 IMPORTANT: Read Before Using. IMPORTANTE: Lea antes de usar.
ENGLISH (Original instructions) SPECIFICATIONS Model: XRJ05 Length of stroke Strokes per minute 32 mm (1-1/4″) High (2) 0 - 3,000 /min Low (1) Max. cutting capacities 0 - 2,300 /min Pipe 130 mm (5-1/8″) Wood 255 mm (10″) Rated voltage D.C. 18 V Standard battery cartridge BL1815N, BL1820, BL1820B Overall length 439 mm (17-1/4″) Net weight • • • BL1830, BL1830B, BL1840, BL1840B, BL1850, BL1850B, BL1860B 3.4 kg (7.6 lbs) 3.7 kg (8.
6. 7. Service 1. Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained. 2. Follow instruction for lubricating and changing accessories. 3. Keep handles dry, clean and free from oil and grease. Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing, and gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.
Symbols CAUTION: Only use genuine Makita batteries. Use of non-genuine Makita batteries, or batteries that have been altered, may result in the battery bursting causing fires, personal injury and damage. It will also void the Makita warranty for the Makita tool and charger. The followings show the symbols used for tool. volts direct current Tips for maintaining maximum battery life no load speed 1. revolutions or reciprocation per minute 2. Important safety instructions for battery cartridge 1. 2. 3.
To remove the battery cartridge, slide it from the tool while sliding the button on the front of the cartridge. Indicating the remaining battery capacity To install the battery cartridge, align the tongue on the battery cartridge with the groove in the housing and slip it into place. Insert it all the way until it locks in place with a little click. If you can see the red indicator on the upper side of the button, it is not locked completely.
Lighting up the front lamp 3 1 1 2 ► 1 . Lock/speed change lever 2. Switch trigger 3. Status of the lock/speed change lever ► 1 . Lamp CAUTION: Do not look in the light or see the source of light directly. A Pull the switch trigger to light up the lamp. The lamp keeps on lighting while the switch trigger is being pulled. The lamp goes out approximately 10 seconds after releasing the switch trigger. B NOTE: Use a dry cloth to wipe the dirt off the lens of the lamp.
Hook CAUTION: When hanging the tool, set the lock/speed change lever in position to lock the switch trigger. (See the section titled “Switch action” .) 1 CAUTION: Never hang the tool at high or potentially unstable location. 2 3 ► 1 . Blade clamp lever 2. Released position 3. Fixed position Insert the recipro saw blade into the blade clamp as far as it will go. The blade clamp sleeve rotates and fixes the recipro saw blade.
To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. NOTE: If you remove the recipro saw blade without rotating the blade clamp lever fully, the lever may not be locked in the released position . In this case, rotate the blade clamp lever fully again, then make sure that the blade clamp lever locked at the released position .
ESPAÑOL (Instrucciones originales) ESPECIFICACIONES Modelo: XRJ05 Extensión de la carrera Carreras por minuto Capacidad máxima de corte 32 mm (1-1/4″) Alta (2) 0 cpm - 3 000 cpm Baja (1) 0 cpm - 2 300 cpm Tubo 130 mm (5-1/8″) Madera 255 mm (10″) Tensión nominal 18 V c.c.
2. 3. 4. 5. 6. 7. Use equipo de protección personal. Póngase siempre protección para los ojos. El equipo protector tal como máscara contra el polvo, zapatos de seguridad antiderrapantes, casco rígido y protección para oídos utilizado en las condiciones apropiadas reducirá el riesgo de lesiones. Impida el encendido accidental.
3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. Use siempre gafas de seguridad o protectoras. Los anteojos comunes o para el sol NO son gafas de seguridad. Evite cortar clavos. Revise la pieza de trabajo y quite todos los clavos antes de utilizar la herramienta. No corte piezas de trabajo demasiado grandes. Compruebe que hay espacio suficiente más allá de la pieza de trabajo antes de cortar para que el disco no golpee el suelo, el banco de trabajo, etc. Sujete la herramienta con firmeza.
PRECAUCIÓN: Utilice únicamente baterías originales de Makita. El uso de baterías no originales de Makita, o de baterías alteradas, puede ocasionar que las baterías exploten causando un incendio, lesiones personales y daños. Asimismo, esto invalidará la garantía de Makita para la herramienta y el cargador Makita. 1 2 Consejos para alargar al máximo la vida útil de la batería 1. 2. 3. 4. Cargue el cartucho de batería antes de que se descargue completamente.
Sobrecarga: La herramienta se está utilizando de una manera que causa que consuma una cantidad de corriente inusualmente alta. En este caso, apague la herramienta y detenga la aplicación que causó que la herramienta se sobrecargara. Luego encienda la herramienta para reiniciarla. Si la herramienta no arranca, significa que la batería se sobrecalentó. En este caso, espere a que la batería se enfríe antes de volver a encender la herramienta.
Freno eléctrico La herramienta está equipada con un freno eléctrico. Si la herramienta falla constantemente en detenerse tras soltar el gatillo interruptor, lleve la herramienta a mantenimiento a un centro de servicio Makita. Iluminación de la luz delantera 1 1 2 ► 1 . Zapata 2. Palanca de ajuste de la zapata NOTA: La zapata no podrá ser ajustada si la palanca de ajuste de la zapata no se abre completamente.
Para extraer la segueta recíproca, gire la palanca de la abrazadera de la segueta completamente en la dirección de la flecha. Una vez extraída la segueta recíproca, la palanca de la abrazadera de la segueta queda fija en la posición liberada . Instalación o extracción de la segueta recíproca PRECAUCIÓN: Limpie siempre las astillas y materias extrañas adheridas al disco y alrededor de la abrazadera de la segueta. En caso contrario, el disco podría quedar no bien apretado ocasionando lesiones graves.
Presione la zapata firmemente contra la pieza de trabajo. No permita que la herramienta dé saltos. Coloque la segueta recíproca de manera que toque ligeramente la pieza de trabajo. Primero, realice un corte de ranura a manera de prueba usando una velocidad más lenta. Luego use una velocidad más rápida para continuar el corte. MANTENIMIENTO PRECAUCIÓN: Asegúrese siempre de que la herramienta esté apagada y el cartucho de batería extraído antes de intentar realizar una inspección o mantenimiento.
< USA only > WARNING Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • lead from lead-based paints, • crystalline silica from bricks and cement and other masonry products, and • arsenic and chromium from chemically-treated lumber.