INSTRUCTION MANUAL MANUAL DE INSTRUCCIONES Cordless Lawn Mower Cortadora de Cesped XML10 XML11 IMPORTANT: Read Before Using. IMPORTANTE: Lea antes de usar.
ENGLISH (Original instructions) SPECIFICATIONS Model: XML10 Mowing width (blade diameter) No load speed 3,000 /min Part number of replacement mower blade 191V96-5 Dimensions (L x W x H) L: 1,780 mm to 1,840 mm (70″ to 72-1/2″) W: 580 mm (22-3/4″) H: 970 mm to 1,100 mm (38-1/4″ to 43-1/4″) Traveling speed – Rated voltage 25.6 - 28.1 kg (56.4 - 61.9 lbs) Protection degree • • 2.5 - 5.0 km/h (1.6 - 3.1 mile/h) D.C. 36 V Net weight • XML11 534 mm (21″) 28.0 - 30.5 kg (61.7 - 67.
7. 8. 9. Watch for holes, ruts, bumps, rocks, or other hidden objects. Uneven terrain could cause a slip and fall accident. Tall grass can hide obstacles. Check the blades or blade bolts carefully for cracks or damage before operation. Replace cracked or damaged blades or blade bolts immediately. Before operation, inspect the mower or blades for any damage. Operation 1. Avoid Dangerous Environment - Never operate the mower in damp or wet locations.
8. 9. 10. 11. 12. 13. 14. 15. 16. Check the blade mounting bolt at frequent intervals for proper tightness. Keep all nuts, bolts, and screws tight to be sure the equipment is in safe working condition. Never remove or tamper with safety devices. Check their proper operation regularly. Never do anything to interfere with the intended function of a safety device or to reduce the protection provided by a safety device.
10. WARNING: Use of this product can create dust containing chemicals which may cause respiratory or other illnesses. Some examples of these chemicals are compounds found in pesticides, insecticides, fertilizers and herbicides. Your risk from these exposures varies, depending on how often you do this type of work.
For XML10 ASSEMBLY WARNING: Always be sure that the lock key and battery cartridge are removed before carrying out any work on the mower. Failure to remove the lock key and the battery cartridge may result in serious personal injury from accidental start-up. WARNING: Never start the mower unless it is completely assembled. Operation of the machine in a partially assembled state may result in serious personal injury from accidental start-up.
2. Insert the frame into the grass basket as far as it will go while holding the handle of the frame. Removing the mulching plug 1. Open the rear cover. 1 1 Fig.7 ► 1 . Handle Fig.4 ► 1 . Rear cover 2. it. NOTICE: Do not insert the handle into the grass basket. Be sure to insert the frame along the stitch of the grass basket. Lift up the mulching plug slightly, and then remove 3. Make sure that there is no sagging on the corners of the grass basket. 1 Fig.5 ► 1 . Mulching plug Fig.
2. Hold the handle of the grass basket, and then hook the grass basket on the rod of the mower body as shown in the figure. 5. Attach all the other clips as shown in the figure. Make sure that all the clips are securely attached to the frame. 1 1 Fig.10 ► 1 . Clip 1 1 2 Installing or removing the grass basket To install the grass basket, follow the steps below. 1. Open the rear cover. 3 Fig.12 ► 1 . Grass basket 2. Handle 3.
To install the battery cartridge; 2. Attach the mulching plug by pushing it as far as it will go so that the protrusions on the mulching plug fit into the holes on the machine. 1. Pull up the locking lever, and then open the battery cover. 1 1 2 Fig.15 ► 1 . Battery cover 2. Locking lever Fig.14 ► 1 . Mulching plug 2. Protrusion 2 2. Align the tongue on the battery cartridge with the slot on the machine, and then slide the cartridge until it locks in place with a little click.
To remove the battery cartridge; Indicating the remaining battery capacity 1. Pull up the locking lever and open the battery cover. 2. Pull out the battery cartridge from the machine while sliding the button on the front of the cartridge. 3. Pull out the lock key. 4. Close the battery cover. 1 Machine / battery protection system The machine is equipped with a machine/battery protection system. This system automatically cuts off power to the motor to extend machine and battery life.
Indicator lamps Lighted Off Switch action Remaining capacity Blinking The battery may have malfunctioned. WARNING: Before installing the battery cartridge, always check to see that the switch lever actuates properly and returns to the original position when released. Operating the machine with a switch that does not actuate properly can lead to loss of control and serious personal injury. NOTE: The mower does not start without pressing the switch button even the switch lever is pulled.
5. Release the drive lever and the switch lever to stop the machine. The table below shows the relationship between the number on the mower body and the approximate mowing height. For XML10 1. Install the battery cartridges. Insert the lock key, and then close the battery cover. 2. Number Press the main power switch. 3. Pull the switch lever toward you while holding down the switch button. Release the switch button as soon as the motor starts running.
When the grass basket is almost full, the indicator does not float while the blades are running. In this case, stop the operation immediately and empty the basket. 2. Adjust the handle height, and then turn the knob on both sides 90°. Make sure that the knobs are securely fixed. 1 Fig.27 ► 1 . Grass level indicator NOTE: This indicator is a rough guide. Depending on the conditions of inside of the basket, this indicator may not work properly.
Using mulching plug The mulching plug allows you to return the cut grass to the ground without gathering the cut grass in the grass basket. When you operate the machine with the mulching plug, be sure to remove the grass basket. NOTICE: When using the machine with the mulching plug, make sure that the total length of grass after cutting is 30 mm (1-3/16″) or more, and the cut length is 15 mm (9/16″) or less. OPERATION Mowing WARNING: Before mowing, clear away sticks and stones from mowing area.
The center lines of the front wheels are guidelines to mowing width. Using the center lines as guidelines, mow in strips. Overlap by one half to one third the previous strip to mow the lawn evenly. 1 2 3 NOTE: Mowing long lawn to short length all at once may cause the lawn to die. The cut lawn may also block up inside of the mower body.
Maintenance Carrying the mower 1. Remove the lock key and battery cartridges, and then close the battery cover. CAUTION: Before carrying the mower, make sure that the battery cartridge and lock key are removed. 2. Put the mower on its side. Clean grass clippings accumulated on the underside of mower deck. When carrying the mower, hold the rear grip and the lower holding part at the front of the machine with two people as shown in the figure. 3.
For XML10 2. Turn the knob 90° while pulling the knob on the lower handle to release the locking pin. Perform the same procedure on the other side, and then fold the handle. 1 1 Fig.41 ► 1 . Knob NOTE: Supporting the handle makes it easier to release the locking pin when pulling the knob. 3. Turn the knob on both sides 90°. Make sure that the knobs are securely fixed. For XML11 Fig.43 ► 1 . Knob NOTICE: Be careful not to pinch the cords when folding the handle. 4.
6. 3. Store the grass basket as shown in the figure. Turn the bolt counterclockwise with box wrench 17. 1 2 1 Fig.45 ► 1 . Grass basket 3 Fig.47 ► 1 . Mower blade 2. Pin 3. Box wrench 1 4. Remove the bolt, and then mower blade. 1 4 Fig.46 ► 1 . Grass basket Removing or installing the mower blade 2 WARNING: The blade coasts for a few seconds after releasing the switch. Do not start any operation until the blade comes to a complete stop. 3 Fig.48 ► 1 . Blade support 2. Mower blade 3.
TROUBLESHOOTING Before asking for repairs, conduct your own inspection first. If you find a problem that is not explained in the manual, do not attempt to disassemble the machine. Instead, ask Makita Authorized Service Centers, always using Makita replacement parts for repairs. State of abnormality Probable cause (malfunction) Remedy Mower does not start. Two battery cartridges are not installed. Install two charged battery cartridges. Battery problem (under voltage) Recharge the battery cartridge.
ESPAÑOL (Instrucciones originales) ESPECIFICACIONES Modelo: XML10 Amplitud de corte del césped (diámetro de la cuchilla) Velocidad sin carga 3 000 r/min Número de pieza de la cuchilla de repuesto de la cortadora de césped 191V96-5 Dimensiones (La x An x Al) L: 1 780 mm a 1 840 mm (70″ a 72-1/2″) An: 580 mm (22-3/4″) Al: 970 mm a 1 100 mm (38-1/4″ a 43-1/4″) Largo: 1 780 mm a 1 840 mm (70″ a 72-1/2″) Ancho: 580 mm (22-3/4″) Alto: 970 mm a 1 100 mm (38-1/4″ a 43-1/4″) - 2,5 km/h - 5,0 km/h (1,6 mil
2. 3. 4. 5. 6. 7. 8. 9. Use vestimenta adecuada - No use prendas sueltas ni joyas. Éstas podrían engancharse en las piezas móviles. Cuando se trabaje en exteriores es recomendable usar guantes de hule y un calzado resistente. No opere la cortadora de césped estando descalzo o con sandalias abiertas. Use gafas de seguridad - Siempre utilice careta o máscara contra polvo si la operación es polvorienta.
20. 21. 22. 23. 24. 25. 26. 27. Corte el césped transversalmente a través de las pendientes, nunca hacia arriba ni hacia abajo. Aplique extrema precaución al cambiar la dirección en las pendientes. Evite cortar el césped en pendientes excesivamente inclinadas. El no pisar sobre suelo firme puede ocasionar resbalones y caídas accidentales. Evite usar la cortadora de césped en pasto húmedo. Pare la operación inmediatamente si nota algo anormal. Apague la cortadora de césped y retire la llave de cierre.
7. 8. 9. 10. 11. No utilice un paquete de baterías o una herramienta que esté dañado/dañada o haya sido modificado/modificada. Las baterías dañadas o modificadas podrían comportarse de manera impredecible causando un incendio, explosión o riesgo de lesión. No exponga un paquete de baterías o una herramienta al fuego o a una temperatura excesiva. La exposición al fuego a una temperatura superior a 130 °C (265 °F) podría causar una explosión.
12. Instrucciones importantes de seguridad para el cartucho de batería 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. Antes de utilizar el cartucho de batería, lea todas las instrucciones e indicaciones de precaución en el (1) el cargador de batería, (2) la batería, y (3) el producto con el que se utiliza la batería. No desarme ni modifique el cartucho de batería. Podría ocurrir un incendio, calor excesivo o una explosión. Si el tiempo de operación se ha acortado en exceso, deje de operar de inmediato.
Para la XML10 MONTAJE ADVERTENCIA: Asegúrese siempre de que la llave de cierre y el cartucho de batería se hayan extraído antes de realizar cualquier trabajo en la cortadora de césped. El no extraer la llave de cierre y el cartucho de batería puede ocasionar lesiones personales graves debido a un encendido accidental. ADVERTENCIA: Nunca ponga en marcha la cortadora de césped a menos que se encuentre completamente ensamblada.
2. Inserte el marco en el canasto para césped lo máximo que se inserte, mientras sostiene el mango del marco. Extracción del tapón para mantillo 1. Abra la cubierta posterior. 1 1 Fig.7 ► 1 . Mango Fig.4 ► 1 . Cubierta posterior AVISO: No inserte el mango en el canasto para 2. Levante el tapón para mantillo ligeramente, y luego quítelo. césped. Asegúrese de insertar el marco a lo largo de la costura del canasto para césped. 3.
5. Coloque los demás sujetadores de presión, como se muestra en la ilustración. Asegúrese de que los sujetadores de presión queden colocados firmemente al marco. 2. Sostenga el mango del canasto para césped y luego enganche el canasto para césped en la barra del cuerpo de la cortadora de césped tal como se muestra en la figura. 1 1 Fig.10 ► 1 . Sujetador de presión 1 1 2 Instalación o remoción del canasto para césped Para instalar el canasto para césped, siga los pasos a continuación. 1.
2. Coloque el tapón para mantillo al empujarlo hasta el máximo que avance, de modo que las protuberancias del tapón para mantillo encajen dentro de los orificios de la máquina. NOTA: La máquina no funciona con solo un cartucho de batería. Para instalar el cartucho de batería; 1. Jale hacia arriba la palanca de bloqueo y luego abra la cubierta de la batería. 1 1 2 Fig.14 ► 1 . Tapón para mantillo 2. Protuberancia Fig.15 ► 1 . Cubierta de la batería 2. Palanca de bloqueo 2 2.
Para retirar el cartucho de batería; Indicación de capacidad restante de la batería 1. Jale hacia arriba la palanca de bloqueo y abra la cubierta de la batería. Jale el cartucho de batería para extraerlo de la máquina 2. mientras desliza el botón en la parte delantera del cartucho. 3. Saque la llave de cierre. 4. Cierre la cubierta de la batería. 1 Sistema de protección de la máquina/batería Esta máquina está equipada con un sistema de protección de la máquina/batería.
Luces indicadoras Iluminadas Apagadas Capacidad restante NOTA: Si la luz indicadora de alimentación principal se enciende en rojo o parpadea en rojo o en verde, consulte las instrucciones para ver lo referente al sistema de protección de la máquina/batería. 75% a 100% NOTA: Esta máquina emplea la función de apagado automático.
4. Mientras sostiene la palanca interruptora, empuje la palanca de accionamiento hacia adelante y sosténgala para accionar las ruedas traseras. 1 Ajuste de la altura de corte del césped ADVERTENCIA: Nunca coloque su mano o pierna debajo del cuerpo de la cortadora de césped cuando esté ajustando la altura de corte del césped. ADVERTENCIA: Asegúrese siempre de que la palanca encaje correctamente en la ranura antes de la operación.
Cuando el canasto para césped está casi lleno, el indicador deja de oscilar mientras las cuchillas están en funcionamiento. En este caso, pare inmediatamente la operación y vacíe el canasto. Sujete el mango inferior con una mano, y luego mueva la palanca de ajuste de la altura de corte del césped con la otra mano. 1 2 1 Fig.25 ► 1 . Palanca de ajuste de la altura de corte del césped 2. Mango inferior Fig.27 ► 1 . Indicador del nivel de césped NOTA: Este indicador es una guía aproximada.
2. Ajuste la altura del mango, y luego gire la perilla en ambos lados 90°. Asegúrese de que las perillas estén bien fijadas. Uso del tapón para mantillo El tapón para mantillo permite echar el pasto cortado al suelo sin recolectarlo en el canasto para césped. Cuando opere la máquina con el tapón para mantillo, asegúrese de retirar el canasto para césped.
OPERACIÓN NOTA: Cuando se corta césped largo o espeso, si se encuentra una irregularidad en la longitud del césped o un acabado deficiente después de cortar el césped, o si se encuentra una disminución de la velocidad del motor durante el corte, disminuya la velocidad de corte a un nivel menor al recomendado en este manual, o aumente la altura de corte. Corte del césped ADVERTENCIA: Antes de cortar el césped, despeje las ramas y piedras del área de podado.
Corte de césped largo MANTENIMIENTO No intente cortar el césped largo en una sola pasada. Procure podarlo en diferentes pasos. Deje pasar uno o dos días entre cada corte hasta lograr que el césped quede cortado de manera uniforme. ADVERTENCIA: Asegúrese siempre de haber extraído la llave de cierre y el cartucho de batería de la cortadora de césped antes de almacenarla o trasladarla o de realizar una inspección o darle mantenimiento.
6. Almacene la cortadora de césped en un lugar seguro y fuera del alcance de los niños. Para trasladar la cortadora de césped, sostenga la empuñadura trasera y la parte de sujeción inferior al frente de la máquina con la ayuda de dos personas, tal como se muestra en la figura. Para la XML11 AVISO: No vierta agua en la zona que se muestra 2 en la ilustración. Verter agua en el motor puede causar un mal funcionamiento de la máquina. 1 Fig.38 ► 1 .
NOTA: Cuando tira de la perilla, dar soporte al mango facilita liberar el pasador de bloqueo. AVISO: Tenga cuidado de no pellizcar los cables 3. Gire la perilla a ambos lados a 90°. Asegúrese de que las perillas estén bien fijadas. 4. Afloje las tuercas de mano de ambos lados, y luego pliegue el mango superior como se muestra en la figura. Para la XML11 cuando pliegue el mango. 2 1 1 Fig.44 ► 1 . Tuerca de mano 2. Mango superior 5. Coloque la máquina en la posición vertical.
4. Retire el perno y luego la cuchilla de la cortadora de césped. Extracción o instalación de la cuchilla de la cortadora de césped ADVERTENCIA: La cuchilla continuará moviéndose por inercia durante algunos segundos tras haber soltado el interruptor. No realice ninguna operación hasta que la cuchilla se haya detenido por completo. 1 ADVERTENCIA: Retire siempre la llave de cierre y el cartucho de batería al extraer o instalar la cuchilla.
RESOLUCIÓN DE PROBLEMAS Antes de solicitar alguna reparación, primero realice una inspección por su cuenta. Si detecta algún problema que no esté explicado en el manual, no intente desarmar la máquina. En vez de esto, solicite la reparación a un centro de servicio autorizado de Makita, usando siempre piezas de repuesto Makita. Estado de la anomalía Causa probable (avería) Remedio La cortadora de césped no arranca. No se han instalado dos cartuchos de batería. Instale dos cartuchos de batería cargados.
Makita Corporation 3-11-8, Sumiyoshi-cho, Anjo, Aichi 446-8502 Japan www.makita.