ENGLISH (Original instructions) SPECIFICATIONS Soda: GALOSH XML | mes Mowing width (bide diameter) 480 mm 534 mm (21%) No load speed 2,800 min 2,300 min Maximum speed 3,300 min 2,800 min Part number of replacement mower blade 1810519 181062-7 Dimensions Liigi0mmin1830mm | L: 1,830 mm to 1,715 mm (84" to (LxWxH) {E312 08512) Wi: 590 ran (23-147) W: 535 mm (217) H: 990 mm to 1,085 mim (38" to 437) He: 980 mm to 1,085 mm (38-172 19 437) Traveling speed 2.8 -80kmih 25-50kmh {1.83.1 milf) {1.6 3.
a. Watch for holes, ruts, bumps, rocks, or other hidden objects. Uneven terrain cooed cuss a sip and fall accident. Tall grass can hide obscenities. Hack the biased or blade bolts carefully for cracks or damage before operation. Replace cracked or damaged blades or bide bolts Immediately. Do not insert or remove the lock key in the rain. Operation Avoid Dangerous Environment Never operate the mower in damp or wet locations. Always ba sure of your footing: keep a fim hold on ths handier and walk; never run.
Maintenance and storage Store Idle Lawn Mower indoors When notion uss, lawn mows should be snored in an indoor dry and locked-up place out of reach of children. Maintain Lawn Mower With Cars Neap curling edges sharp and clean for best and safest performance. Follow instructions for lubricating and changing accessories. Inspect lawn mower cord periodically and if damaged, have it repaired by an authorized service facility. Keep handles dry, clean, and free from oil and grass.
. Do not handle charger, including charger plug, and charger terminals with wet hands. 8. Do not charge lawn mower In rain, or In wet locations. 7. When replacing batteries, all batteries should be replaced st the same time. Mixing fresh and discharged batteries could increase internal cell pressure and rupture the discharged battery. 8 Exercise care In handling batteries in order not to short the battery with conducting materials such as rings, bracelets, and keys.
Tips for maintaining maximum battery life 1. Charge the battery cartridge before compositely discharged. Always stop too! operation and charge the battery cartridge when you notices less fool power. Haber recharge a fully charged battery cartridge. C Overcharging shortens the battery service life. 3. Charge the gallery cartridges with room tempera true 104 °F). Let a hot battery cartridge cool down before charging it.
o & 2. Hold the handle of the grass basket, and then Removing the mulching plug hook the grass basket on the rod of the mower body as 4. Gen the rear cover. shown in the figure. B 1. Rear cover P 1. Rod 2. Handle 3. Grass basket 2. Remove the mulching plug while holding down the To remove the grass basket, open the rear cover, and then remove the grass basket by holding the handle. Attaching the mulching plug 4. Open the rear cover, and then remove the grass basket. #1. Lever 2.
Fer For XMLO7TNMLOS 1. Open the rear cover, and then remove the grass basket. ¥ 1. Rear cover 2. Grass basket 2. Attach the mulching plug while holding down the lever, and then rel sass the lever to lock the mulching plug. FUNCTIONAL DESCRIPTION CE EE EDEN Installing or removing battery cartridge CAUTION: Always switch off the machine before Installing or removing of the battery cartridge. CAUTION: Hold the machine and the battery cartridges firmly when Installing or removing battery cartridges.
QUOTE: Install at least 2 battery cartridges to battery port 1 or battery port 2. 3. Insert the lock key in the places shown in the figure as far as it will go. # 1. Lock key 4. Loss the battery cover and push it until iris latched with the locking lever. To removes the battery cartridge; 4. Pull up ths locking lever and open the battery cover. 2. Pull gut the battery cartridge from the machine while sliding the button on the front of the cartridge. 3. Pullout the lock key. 4. Close the battery cover.
NOTE: Depending on the conditions of use and the ambient temperature, the indication may differ slightly from the actual capacity. The control pans! has the main prows switch, the mods switching button, and tha indicator of remaining battery capacity. 1 ¥ 1. Gallery indicator 2. Soda switching lamp 3. Main power lamp 4. Hack button 5. Mods switching button 8. Main power switch Main power switch WARNING: Always turn off the man power switch when not In use.
4. Pull the switch lever toward you while holding down the switch button. Release the switch bunion as soon as the motor stars running. 4. Pull the switch lever toward you while holding down the switch bunion. Release the switch button as soon as the moor starts running. B 1. Switch button 2. Switch lever BP 1. Switch bunion 2. Switch lever HOT: if the lock key is not inserted, the power lamp blinks In green when you pull the switch lever.
Number Owing height 1 20 mm (13/167) 28mm (17) 32 mm (3-149 38 mm 47 mm 55 mm 63 mm (21/27) 74 mm fain 88 mm (3-387 10 100 mm (315/167) Hold the front grip or the lower handle with one hand, and then move the mowing height adjusting lever with the other hand. ¥ 1. Mowing height adjusting lever 2. Lower handle 3. Front grip NOTE: The mowing height figures should be used just as a guideline.
Adjusting the traveling speed For XMLOGMMLOS #1. Speed lever Ths travailing speed can ba adjusted with the speed lever. To decreases the sped, pull the Rivers toward you, and to increase the speed, turn the lever forward. Using mulching plug The mulching plug allows you to return the cut grass fo the ground without gathering the cut grass in the grass basket. When you operate the machine with the mooching plug, be sure to remove the grass basket.
The center lines of the front wheels are guidelines to mowing width. Using the center lines as guidelines, mow in strips. Overlap by one half to one third ths previous strip to mow the lawn evenly. #1. Mowing width 2. Overlapping area 3. Center line Change the mowing direction sate teems to prevent the grass grain pattern from forming in just one direction. Periodically check the grass basket for mowed grass. Empty the grass before it becomes full.
MAINTENANCE WARNING: Always be sure that the lock key and battery cartridge are removed from the mower before storing or carrying the mower or attempting to perform inspection or maintenance. WARNING: Always remove ths lock key when the mower is not in use. Store the lock key ina safe place out of reach of children. WARNING: Wear gloves when performing inspection or maintenance. WARNING: Always wear the safely goggles or safely glasses with side shields when performing inspection or maintenance.
3. Tum the bolt counterclockwise with box wrench 17. #1. Mows blade 2. Pin 3. Box wrench 4. Removal the bolt, and then mower blade. ¥ 1. Blade support 2. Mower blade 3. Bolt 4. Protrusion NOTICE: When Installing the mower blade, make sure that the protrusions on the blade support fit in the holes in the mower blade. Installing the mower blade WARNING: Install the mower blade carefully. It has a top/bottom facing. WARNING: Tighten the bolt clockwise firmly {0 secures the blade.
TROUBLESHOOTING Before asking for repairs, conduct your own inspection first. If you find a problem that is not explained in the manual, do not attempt fo disassemble the machine. Instead, ask Akita Authorized Service Centers, always using Akita replacement pairs for repairs. Stale of abnormality Probables causal {malfunction} Ready Mower does not start Two battery cartridges are not installed. | Install two changed battery cartridges. Battery problem {under voltage) Recharge the battery cartridge.
9. Use gafas de seguridad Siempre utilice careta 0 mascara contra polvo 3i le operación es polvorienta. Los obleas que sean golpeados por {a cuchilla de ia cortadora de césped pueden causar lesiones personales graves. El césped debe sor examinado cuidadosamente y despejada de cualquier objeto antes ds proceder 2 cortare. Manténgase detrás del mango cuando of motor esté funcionando. Asegúrese de que no haya otras personas en el rea de trabajo antes de corlar el césped.
He treta lg Lag tel AVISO: Cuando instala los mangos, posicione los cables de {al manera gus no queden enganchados con nada sirenio los mangos. Si un cables estad fidelidad, ef Interruptor de ia cortadora de césped podría ne funcionar. 4. Alinee los orificios del mane Inferior con los artificios en el cuerpo de la coladora de clase, luego apriete 0s 4 peamos provisionalmente. ¥ 1. Mango inferior 2. Perno 2.
Fraccione del tapón para mantillo 4. Abra la cubriera posterior. #1. Cubierta posterior 2. Retire ef tapen para mantillo mientras sostiene hacia abajo la palanca. ¥ 1. Palanca 2. Tapan para mantillo Instalación o remoción del canasto para césped Para instalar el canario para césped, siga ios pasos a continuación. 4. Abra la cubista posterior. ¥ 1. Cubierta posterior 2.
Para ol modelo XMLO7 1. Instale ios claruchos de batearla. Inserta la lave de cierre y luso cleros 1a cubista de [a batearla. 2. Seleccione los claruchos de batería deslizares para funcionamiento al girar of interruptor de selección de baterías. 3. Oprima el interruptor de alimentación principal. 4. Tire de la palanca interruptora hacia usted míen tras mantienes presionado al boten interruptor. Suelte el boten interruptor tan pronto como sl motor guarangas. ¥ 1. Botan interruptor 2.
Indicador del nivel de césped El Indicador dei nivel de césped muestra ef volumen de césped pesado. Cuando ef canario para césped ne estad len, el indicador oscila mientras lee cuchichiaras están en funcionamiento ¥ 1. Indicador dsl nivel de césped Cuando el canasto para césped esté casi len, of indicador deja de oscilar mientras las cuchillas estén en funcionamiento. En este caso, pare inmediatamente la operacional y vais sl canasto. NOTA: Este indicador es una guía aproximada.
Uso del tapón para mantillo El tapan para mantillo permite echar ef paso cortado al suelo sin recolectarlo en el canasto para césped. Cuando opera la maquina con el lapón para amantille, aseglares de retirar ol canasto para césped AVISO: Cuando utilices la quinquis con ol traspón para amantille, asegúrese de que la longitud total del césped sea de 30 mm {1-3/8 o més, 0 Ia longitud de corte sea de 15 mm 0 menes.
Extracción de la cuchilla de la cortadora de césped 41. Coligue de lado ia cortadora de césped de tal forma que la palanca de ajuste de Ia aliare de corte dai césped quede orientada lacha i lado de alba. 2. Para soguear la cuchilla, inserís el pasador en un oficio de! cuerpo de Ia cortadora de césped. 3. Gire el pero con la lave de bufas 17 en sentido inverso al de las manecillas del reloj. # 1. Cuchilla de la cortadora de césped 2. Pasador 3. Lave de bujías 4.