INSTRUCTION MANUAL MANUAL DE INSTRUCCIONES Cordless Driver Drill Atornillador Taladro Inalámbrico XFD11 IMPORTANT: Read Before Using. IMPORTANTE: Lea antes de usar.
ENGLISH (Original instructions) SPECIFICATIONS Model: XFD11 Drilling capacities Steel Fastening capacities Wood screw 13 mm (1/2") Wood 36 mm (1-7/16") 6 mm x 75 mm (1/4" x 2-15/16") Machine screw No load speed (RPM) M6 (1/4") High (2) 0 - 1,700 /min Low (1) 0 - 500 /min Overall length 162 mm (6-3/8") Rated voltage D.C. 18 V Standard battery cartridge Net weight • • • BL1815N, BL1820B BL1830, BL1830B, BL1840B, BL1850B, BL1860B 1.3 kg (2.8 lbs) 1.5 kg (3.
6. 7. Service 1. Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained. 2. Follow instruction for lubricating and changing accessories. 3. Keep handles dry, clean and free from oil and grease. Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing, and gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.
2. Important safety instructions for battery cartridge 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. Before using battery cartridge, read all instructions and cautionary markings on (1) battery charger, (2) battery, and (3) product using battery. Do not disassemble battery cartridge. If operating time has become excessively shorter, stop operating immediately. It may result in a risk of overheating, possible burns and even an explosion.
Overdischarge protection Indicating the remaining battery capacity When the battery capacity is not enough, the tool stops automatically. In this case, remove the battery from the tool and charge the battery. Only for battery cartridges with "B" at the end of the model number NOTE: Overheat protection (for battery) will work only with batteries with star marking. 1 1 2 ► 1. Indicator lamps 2. Check button ► 1.
This tool has a reversing switch to change the direction of rotation. Depress the reversing switch lever from the A side for clockwise rotation or from the B side for counterclockwise rotation. When the reversing switch lever is in the neutral position, the switch trigger cannot be pulled. Lighting up the front lamp Speed change 1 ► 1. Lamp CAUTION: Do not look in the light or see the source of light directly. 1 Pull the switch trigger to light up the lamp.
Adjusting the fastening torque 1 2 3 ► 1. Adjusting ring 2. Graduation 3. Arrow The fastening torque can be adjusted in 21 levels by turning the adjusting ring. Align the graduations with the arrow on the tool body. You can get the minimum fastening torque at 1 and maximum torque at marking. The clutch will slip at various torque levels when set at the number 1 to 20. The clutch does not work at the marking.
Installing driver bit holder Screwdriving operation Optional accessory CAUTION: Adjust the adjusting ring to the proper torque level for your work. CAUTION: Make sure that the driver bit is inserted straight in the screw head, or the screw and/or driver bit may be damaged. 1 Place the point of the driver bit in the screw head and apply pressure to the tool. Start the tool slowly and then increase the speed gradually. Release the switch trigger as soon as the clutch cuts in.
• • • • • Using the tool as a hand screwdriver Drill bits Driver bits Driver bit holder Hook Makita genuine battery and charger NOTE: Some items in the list may be included in the tool package as standard accessories. They may differ from country to country. MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory.
ESPAÑOL (Instrucciones originales) ESPECIFICACIONES Modelo: XFD11 Capacidades de taladrado Acero Capacidades de apriete Tornillo para madera 13 mm (1/2") Madera 36 mm (1-7/16") 6 mm x 75 mm (1/4" x 2-15/16") Tornillo de máquina Velocidad sin carga (rpm) 6 mm (1/4") Alta (2) 0 - 1 700 r/min Baja (1) 0 - 500 r/min Longitud total 162 mm (6-3/8") Tensión nominal 18 V c.c.
2. 3. 4. 5. 6. 7. cansado o bajo la influencia de drogas, alcohol o medicamentos. Un momento de distracción mientras opera las herramientas eléctricas puede terminar en una lesión grave. Use equipo de protección personal. Póngase siempre protección para los ojos. El equipo protector tal como máscara contra el polvo, zapatos de seguridad antiderrapantes, casco rígido y protección para oídos utilizado en las condiciones apropiadas reducirá el riesgo de lesiones. Impida el encendido accidental.
3. 4. 5. 6. 7. 8. 9. Sujete la herramienta eléctrica por las superficies de agarre aisladas al realizar una operación en la que el sujetador pueda entrar en contacto con cables ocultos. Si el sujetador entra en contacto con un cable con corriente, las piezas metálicas expuestas de la herramienta eléctrica se cargarán también de corriente y el operario puede recibir una descarga. Asegúrese siempre de que pisa sobre suelo firme.
2. 3. 4. No cargue nunca un cartucho de batería que esté completamente cargado. La sobrecarga acortará la vida de servicio de la batería. Cargue el cartucho de batería a una temperatura ambiente de 10 °C - 40 °C (50 °F - 104 °F). Si un cartucho de batería está caliente, déjelo enfriar antes de cargarlo. Cargue el cartucho de batería si no va a utilizarlo durante un período prolongado (más de seis meses).
Protección contra sobrecarga Cuando la herramienta/batería se esté utilizando de una manera que cause que consuma una cantidad de corriente inusualmente alta, la herramienta se detendrá automáticamente sin que haya indicación alguna. En este caso, apague la herramienta y detenga la aplicación que causó que la herramienta se sobrecargara. Luego encienda la herramienta para reiniciarla.
Accionamiento del conmutador de inversión de giro A Cambio de velocidad B 1 1 ► 1. Palanca de cambio de velocidad ► 1. Palanca del interruptor de inversión PRECAUCIÓN: Coloque siempre la palanca de cambio de velocidad exactamente en la posición correcta. Si usted utiliza la herramienta con la palanca de cambio de velocidad puesta a medias entre la posición “1” y “2”, la herramienta puede dañarse. PRECAUCIÓN: Confirme siempre la direc- ción de rotación antes de la operación.
La torsión de apriete puede ajustarse en 21 niveles girando el anillo de ajuste. Alinee las graduaciones con la flecha en el cuerpo de la herramienta. Puede conseguir una fijación de torsión mínima en 1 y una torsión máxima en la . marca El embrague se deslizará entre los diferentes niveles de torsión cuando esté ajustado en los números 1 a 20. El embrague no funciona en la marca .
Coloque el portabrocas en la protuberancia en la base de la herramienta o ya sea del lado derecho o izquierdo y asegúrelo con un tornillo. Cuando no utilice la punta de destornillador, manténgala dentro del portabrocas. Las puntas de destornillador de 45 mm de largo (1-3/4") se pueden guardar ahí. Operación de taladrado Primero, gire el anillo de ajuste de tal forma que la flecha apunte hacia la marca . Después proceda como sigue.
Si necesita cualquier ayuda para más detalles en relación con estos accesorios, pregunte a su centro de servicio local Makita. • Brocas de taladro • Puntas de destornillador • Portabrocas • Gancho • Batería y cargador originales de Makita Uso de la herramienta como atornillador manual NOTA: Algunos de los artículos en la lista pueden incluirse en el paquete de la herramienta como accesorios estándar. Éstos pueden variar de país a país. GARANTÍA LIMITADA DE UN AÑO DE MAKITA Apague la herramienta.
< USA only > WARNING Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • lead from lead-based paints, • crystalline silica from bricks and cement and other masonry products, and • arsenic and chromium from chemically-treated lumber.
DC18RA DC18RC Fast Charger Chargeur rapide Cargador rápido Symbols The followings show the symbols used for the charger and battery. Be sure that you understand their meaning before use. Symboles Nous donnons ci-dessous les symboles utilisés pour le chargeur et la batterie. Assurez-vous que vous en avez bien compris la signification avant d’utiliser l’outil. Símbolos A continuación se muestran los símbolos utilizados con el cargador y la batería. Asegúrese de que entiende su significado antes de usarla.
• Do not short batteries. • Ne jamais court-circuiter les bornes d’une batterie. • No provoque un cortocircuito en las baterías. IMPORTANT: Read Before Using. IMPORTANT : Lire ce qui suit avant d’utiliser cet outil. IMPORTANTE: Leer antes de usar.
ENGLISH Specifications Model DC18RA Input DC18RC A.C. 120 V 50 – 60 HZ Output Weight D.C. 7.2 V – 18 V 0.88 kg (1.94 lbs) 0.77 kg (1.70 lbs) • Manufacturer reserves the right to change specifications without notice. • Note: Specifications may differ from country to country. • Weight according to EPTA-Procedure 01/2003. IMPORTANT SAFETY INSTRUCTIONS CAUTION: 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17.
5. With finish of charge, the green light remains lit with the red light going out and the melody sound preset at the insertion of battery cartridge or buzzer sound (a long beep) comes out to notify completion of charge. (In selected silent mode, no sounds come out.) 6. Preset melody sound remains stored even when the charger is unplugged. NOTE: • The battery charger is for charging Makita-battery cartridge. Never use it for other purposes or for other manufacturer’s batteries.
FRANÇAIS Spécifications Modèle Entrée DC18RA DC18RC C.A. 120 V 50 – 60 Hz Sortie Poids C.C. 7,2 V – 18 V 0,88 kg (1,94 lbs) 0,77 kg (1,70 lbs) • Le fabricant se réserve le droit de modifier sans avertissement les spécifications. • Remarque : Les spécifications peuvent varier selon les pays. • Poids selon la procédure EPTA 01/2003. LES CONSIGNES DE SECURITE IMPORTANTES ATTENTION : 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17.
Changer la mélodie de charge terminée 1. Lorsque vous insérez la batterie dans le chargeur, le chargeur émet la dernière courte mélodie préréglée d’indication de charge terminée. 2. Si vous retirez et réinsérez la batterie dans les cinq secondes qui suivent cette action, la mélodie changera. 3. Chaque fois que vous retirez et réinsérez la batterie dans les cinq secondes par la suite, la mélodie change dans l’ordre préétabli. 4.
Tension 9,6 V 12 V 14,4 V Nombre de cellules 8 10 12 Cartouche de batterie au Ni-MH Capacité (Ah) Temps de charge (en minutes) 20 — — — 1,7 BH9020A — — 2,0 20 — BH1220/C BH1420 2,0 15 20 — — — 2,7 BH9033A — — 3,3 30 — BH1233/C BH1433 3,3 22 Tension 14,4 V 18 V 14,4 V 18 V Nombre de cellules 4 5 8 10 Cartouche de batterie au Li-ion BL1415 BL1815 — — 15 — — BL1430 BL1830 22 Temps de charge (en minutes) Note : • La charge complète peut prendre jusqu’
ESPAÑOL Especificaciones Modelo DC18RA 120 V Entrada Salida Peso DC18RC 50 – 60 Hz 7,2 V cc – 18 V cc 0,88 kg (1,94 lbs) 0,77 kg (1,70 lbs) • El fabricante se reserva el derecho a cambiar las especificaciones sin aviso. • Nota: Las especificaciones podrán cambiar de un país a otro. • Peso de acuerdo con el procedimiento EPTA 01/2003. INSTRUCCIONES DE SEGURIDAD IMPORTANTES PRECAUCION: 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17.
Cambio de la melodía de carga terminada 1. 2. 3. 4. Al insertar el cartucho de batería en el cargador se emite el último sonido de melodía breve programado. El sonido de melodía puede cambiarse extrayendo y reinsertando antes de cinco segundos el cartucho de batería. Cada vez que se extraiga y reinserte antes de otros cinco segundos, el sonido de melodía cambiará en orden. Cuando se emita el sonido de melodía deseado, deje el cartucho de batería insertado y comenzará la carga.
Tensión 9,6 V cc 12 V cc 14,4 V cc Número de celdas 8 10 12 Capacidad (Ah) Cartucho de batería Ni-MH Tiempo de carga (minutos) — — — 1,7 Ah 20 min BH9020A — — 2,0 Ah 20 min — BH1220/C BH1420 2,0 Ah 15 min — — — 2,7 Ah 20 min BH9033A — — 3,3 Ah 30 min — BH1233/C BH1433 3,3 Ah 22 min Tensión 14,4 V cc 18 V cc 14,4 V cc 18 V cc Número de celdas 4 5 8 10 Cartucho de batería Li-ion BL1415 BL1815 — — 15 min — — BL1430 BL1830 22 min Tiempo de carga (min
11
Makita Corporation 3-11-8, Sumiyoshi-cho, Anjo, Aichi 446-8502 Japan 884676H946 IDE www.makita.