ENGLISH (Original instructions) INSTRUCTION MANUAL Vacuum Cleaner VC1310L VC2510L VC3210L 011586 IMPORTANT: Read Before Using.
ENGLISH (Original instructions) SPECIFICATIONS Model VC1310L / VC2510L / VC3210L Voltage EU AU/NZ GB 110V GB 230V CL Volt 230 - 240 230 - 240 110 230 - 240 220 Power consumption Watt 1050 1050 1050 1050 1050 Connected load for appliance socket Watt at symbol mode 2400 1350 650 2000 2400 Connected load for appliance socket Watt at symbol mode 2600 1600 950 2400 2600 Total connected load Watt 3650 2650 2000 3450 3650 VC2510L VC3210L Model VC1310L Volume flow (air
ENH038-1 For European countries only EC Declaration of Conformity 7. We Makita Corporation as the responsible manufacturer declare that the following Makita machine(s): Designation of Machine: Vacuum Cleaner Model No.
21. 22. 23. 24. 25. 26. 27. 28. 29. 30. 31. 32. 33. 34. Clean and service the cleaner immediately after each use to keep it in tiptop operating condition. MAINTAIN THE CLEANER WITH CARE. Keep the cleaner clean for better and safer performance. Follow instructions for changing accessories. Inspect cleaner cords periodically and if damaged, have repaired by authorized service facility. Inspect extension cords periodically and replace if damaged. Keep handles dry, clean, and free from oil and grease.
symbol. electric power tool input power. Switching on and off of the connected electric power tool simultaneously brings the cleaner switching on and off action. The cleaner still works for a few seconds even after the electric power tool is switched off. After use, disconnect the power tool from the socket of cleaner. Switch off the cleaner after use. Connecting electric power tools • • WARNING: Observe the maximum connected loads for the appliance socket (Refer to the SPECIFICATIONS.
1. Locking or unlocking the caster Storing the power supply cord NOTE: • Do not use the cleaner or a connected electric power tool with a power supply cord wound on the base hook. Using the cleaner or the connected electric power tool with power supply cord may cause damage the power supply cord. For Models VC1310L and VC2510L 3 1. Power supply cord 2. Base hook 1 1. Caster 2. Stopper lever 3. FREE position 4. LOCK position 4 2 1 011611 2 For Model VC3210L 011597 1. Caster 2. Stopper lever 3.
between the water filter and the tank. Also, install the water filter so that the mounting position marking can be aligned. Installing the water filter NOTE: • Models VC2510L and VC3210L have no mounting position marking and no need to align it. 1 6 Installing the paper pack 2 • 3 4 • WARNING: When using the paper pack, also use the prefilter together that is preinstalled on the tool. Failure to use the prefilter together may cause unusual noise and heat, resulting in a fire.
detent protrusion. Installing the pipe holder (optional accessory) 2 For Model VC1310L only 1. Cord hook 1. Tank cover 2. Protrusion of the pipe holder 3. Groove 1 3 011607 1 011604 Depress the cord hook as shown in the figure. 2 3 011608 Fit two protrusion of the pipe holder into the grooves of the tank cover and then press down the pipe holder. 1 1. Tank cover 2. Hook 1 4 5 2 011631 1. Press 2. Pipe holder 3. A section 4. Hooks 5.
pulling the hose may cause a breakage or deformation of the hose. When picking up large wastes such as planer carvings, concrete dusts or similars other than small wastes, use the 38 mm inner diameter hose (optional accessory). Using the 28 mm inner diameter hose may cause a hose stuffing and damage. • Too much dust will tear the bag easily, so do not collect the dust more than the half of the bag capacity.
Installing powder filter Carrying the cleaner 1. Handle 2. Head 1 2 1 6 2 011610 3 When carrying the cleaner, carry it by holding the handle on the head as shown in the figure. The handle is retractable at the head when not in use. 4 MAINTENANCE • 5 CAUTION: Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance. Storage of power supply cord 1. Tank cover 2. Powder filter 3. Damper 4. Prefilter 5. Tank 6.
Pipe holder can be used to store straight pipe, bent pipe, corner nozzle and similars by just inserting these accessories. For Models VC2510L and VC3210L 1. Cord hook 2. Power supply cord 1 1 2 011635 1. Power supply cord 2. Base hook 1 2 2 1. Stopper 2. Pipe holder 011634 011613 Wind up the power supply cord around the base hook. The pipes can be placed into the pipe holder when also stopping using the cleaner on the way for a while.
NOTE: • Do not rub and scratch the powder filter, the prefilter or the damper with hard objects such as a brush and a paddle. • The filters are consumable and are recommended to have some spares for them. To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should be performed by Makita Authorized Service Centers, always using Makita replacement parts.
Makita Corporation Anjo, Aichi, Japan 884995-229 16 www.makita.