6" (406 mm) MODEL UM40lDW Convertlble Rear Bag I Mulching With Charger INSTRUCTION MANUAL SPECIFICATIONS Model UMlOlD II Effective cutting width No load Speed fRPM1 16" (406 m m ) 3.
IMPORTANT SAFETY INSTRUCTIONS (For Gardening Appliances) WARNING: WHEN USING CORDLESS TOOLS, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PERSONAL INJURY, INCLUDING THE FOLLOWING: SAVE THESE INSTRUCTIONS. READ ALL INSTRUCTIONS. 1 . Avoid Dangerous Environment - Don't use appliances in damp or wet locations. 2. Don't Use In Rain. 3. Keep Children Away - All visitors should be kept at a distance from work area. 4.
damaged, have it repaired by an authorized service facility. Inspect extension cords periodically and replace if damaged. Keep handles dry, clean, and free from oil and grease. 16. Remove Adjusting Wrenches. Form habit of checking t o see that adjusting wrenches are removed from mower before turning it on. 17.
111 1 Inspect for damage. I V ) Repair any damage before restarting and operating the lawn mower. 30. CHECK THE REAR BAG FREQUENTLY FOR WEAR OR DETERIORATION. For storage, always make sure the rear bag is empty. Replace a worn bag w i t h a new factory replacement bag for safety. Order Part No. 1 6 6 0 4 5 9 31. Stop the motor and remove key whenever you leave the equipment, before cleaning the mower housing, and before making any repairs or inspections. 32.
IMPORTANT SAFETY INSTRUCTIONS FOR BATTERIES & CHARGER I . SAVE THESE INSTRUCTIONS - This manual contains important safety and operating instructions for battery charger. 2.Before using battery charger, read all instructions and cautionary markings on (1) battery charger and (2)product using battery. 3. CAUTION - To reduce risk of injury, charge ONLY MAKITA type rechargeable batteries used in Model UM401D. Other types of batteries may burst causing personal injury and damage. 4.
ADDITIONAL SAFETY RULES FOR BATTERIES IN MOWER 1. Use ONLY the Makita charger Model DC240 specified t o charge the Makita model UM4OlD. 2. Do not short the battery: 1) Do not touch the charging inlet w i t h any conductive material. 2) Shut the cover on the charging inlet when not charging. 3)Do not expose mower t o water or rain. A battery short can cause a large current flow, overheating, possible burns and even a breakdown. 3.Do not leave mower exposed t o direct sunlight.
ADDITIONAL SAFETY RULES FOR CHARGER 1. The Makita charger Model D C 2 4 0 is specifically designed t o charge only the Makita batteries used in Model UM401D. D o not attempt t o charge any other battery with this charger. 2. Handle the charger carefully. Do not drop or strike it. 3. Never carry the charger by cord or yank it t o disconnect from receptacle. 4. Keep cord from heat, oil, chemicals, and sharp edges. 5.
Unpacking Your mower has been completely assembled at the factory except for the rear bag. 1. Remove the rear bag, instruction manual, charger and plastic bag containing accessories from the carton. 2. Remove the mower from the carton and place all four wheels on the ground or,floor. 3. Check the carton thoroughly and make sure there are no loose parts. 4. To unfold the handle, raise it into place.
NOTE *If the charging light flashes in green color, the charging plug may not be inserted into the charging inlet correctly Check the charging plug and charging inlet *If the charging light flashes in red color the batteries are too weak for normal charging Wait for a while until normal charging starts after recovery charging is finished *If the mower has not been used for long periods.
Wheel height adjustment (six steps between 1" and 3-1/2" or 25 mm and 89 mm). 1. Turn off the interlock switch and remove the key. If you are recharging the mower, stop recharging and disconnect the charging plug. 2. Push the lever outward and fit it into one of the grooves for your desired cutting height. This one touch wheel height adjustment system can adjust all four wheels at the same time. CAUTION: Always make sure that the lever is fit in the groove properly before operation.
WARNING: Replace bent or damaged blade immediately. A bent or damaged blade may cause excessive vibration, resulting in damage to the mower or serious injury to operator. Blade sharpening Keep the blade sharp and clean for best performance. A dull blade does not cut grass cleanly and evenly. It may overload the motor and waste more battery energy 1. Turn off the interlock switch and remove the key. If you are recharging the mower, stop recharging and disconnect the charging plug. 2.
Emptying rear bag 1. Release the switch lever. 2. Turn off the interlock switch and remove the key 3. Open the rear guard. 4. Hold the rear bag handle and remove the rear bag from the mower. 5 . Empty the grass from the rear bag. Rear guard - Rear bag WARNING: To reduce risk of injury, inspect rear bag frequently and replace with recommended replacement if there are signs for wear or deterioration. Installing mulching plate 1. Turn off the interlock switch and remove the key.
Mulching While mulching, your new mower is designed to cut the grass clipptngs into small pieces and distribute them back into the lawn. Under normal conditions, the mulched grass will biodegrade quickly to provide nutrients to the lawn. Please review the following recommendations for optimum mulching performance. 1. Avoid mowing when the grass is wet from rain or dew. Wet grass may from clumps which interfere with the mulching action and reduce run-time.
4 Pull the switch lever toward you while depressing the switch button 5 Release the switch button as soon as the motor starts running The mower will continue to run until you release the switch lever 6 The indicator indicates remaining capacity of the battery only when the motor is running 7 Release the switch lever to stop the motor 8 When not in use, turn off the interlock switch and remove the key Store the key in a safe place out of reach of children Overload protector This mower is equipped with an ov
Maintenance & Storage 1. REMOVE KEY. Store it in a safe place out of the reach of children. 2. Clean your mower using only mild soap and a damp cloth. Do not spray or pour water on your mower when cleaning. 3. Turn mower on its side and clean grass clippings that have accumulated on the underside of mower deck. 4. Check all nuts, bolts, knobs, screws, fasteners, etc. for tightness. 5. Inspect moving parts for damage, breakage, and wear. Have repairs made on any damaged or missing parts. 6.
ACCESSORIES CAUTION These accessories or attachments are recommended for use with your Makita tool specified in this manual The use of any other accessories or attachments might present a risk of injury to persons The accessories or attachments should be used only in the proper and intended manner *Charger Model DC240 *Mulching plate Part No. 416211-1 *Wrench 32 Part No. 781028-4 16 *Swing arm blade Pan No. 72901 1-5 *Socket wrench 13 Pan No.
Dec-19-'96 US 16" (406 mm) CORDLESS LAWN MOWER Model UM401DW 17
Note: The switch and other part configurations may differ from country to country.
MODEL U M 4 O l D W izD Dec-19- 96 US DESCRIPTION M MACHINE X E ~ 58 1 Torsion Spr8ng 20 59 60 61 62 1 LeVOI 7 4 8 9 IO 1 1 2 Tapping Screw 41 I 8 CDWhng Complete Tapping Screw Flange 4x25 Tapping Screw 4 r 18 Flat Washer 4 TenSlOn Sprlnp 1 2 Her Lock Nul M6- IO Deck Rear Shall Flat Washer IO 67 1 11 2 Flat Washer 10 68 2 ComDreSrlon SD"ng 16 Switch Bunon Tension Spring 5 Switch Switch 801 Cover Tapping Screw 4 ~ 1 8 12 2 8 69 1 Slra!" Aellel 13 14 15 16 2 Bolt 3/B 16UN
MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanshlp and materials for the period of ONE YEAR from the date of originid purchase. Should any trouble develop during this one-year period, return the COMPLETE tool, freight prepaid, t o one of Makita’s Factory or Authorized Service Centers.