ENGLISH (Original instructions) INSTRUCTION MANUAL Concrete Planer PC5000C PC5001C 009839 DOUBLE INSULATION IMPORTANT: Read Before Using.
ENGLISH (Original instructions) SPECIFICATIONS Model PC5000C PC5001C Wheel diameter 125 mm Hole diameter 22.23 mm Spindle thread M14 Rated speed (n)/No load speed (n0) 10,000 min-1 Overall length 437 mm Net weight 4.0 kg 479 mm 5.1 kg Safety class /II • Due to our continuing program of research and development, the specifications herein are subject to change without notice. • Specifications may differ from country to country.
GEA005-3 • • WARNING: The vibration emission during actual use of the power tool can differ from the declared emission value depending on the ways in which the tool is used. Be sure to identify safety measures to protect the operator that are based on an estimation of exposure in the actual conditions of use (taking account of all parts of the operating cycle such as the times when the tool is switched off and when it is running idle in addition to the trigger time).
22. Personal safety 11. Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury. 12. Use personal protective equipment. Always wear eye protection.
6. 7. 8. 9. 10. 11. 12. 13. 14. Regularly clean the power tool’s air vents. The motor’s fan will draw the dust inside the housing and excessive accumulation of powdered metal may cause electrical hazards. 15. Do not operate the power tool near flammable materials. Sparks could ignite these materials. 16. Do not use accessories that require liquid coolants. Using water or other liquid coolants may result in electrocution or shock.
adequately guarded and are unsafe. b) Always use undamaged wheel flanges that are of correct size and shape for your selected wheel. Proper wheel flanges support the wheel thus reducing the possibility of wheel breakage. Additional safety warnings: 17. Always install the dust cover before operation. 18. Be careful not to damage the spindle, the flange (especially the installing surface) or the lock nut. Damage to these parts could result in wheel breakage. 19.
To change the amount of stock (concrete) removed, loosen the hex socket head bolts on the base holder with the hex wrench. Raise or lower the front roller to adjust the gap between it and the diamond wheel. The difference is the stock removal amount. Then secure the hex socket head bolts very carefully. Electronic function Constant speed control Possible to get fine finish, because the rotating speed is kept constantly even under the loaded condition.
2 1 Max. 6 ASSEMBLY 1. Same level 2. Square or ruler 3. Hex socket head bolt • CAUTION: Always be sure that the tool is switched off and unplugged before carrying out any work on the tool. Installing or removing diamond wheel 3 009851 NOTE: • After base adjustment, turn the three hex socket head bolts on the base counterclockwise until the heads are flush with the back side of the base. Turn gently or base adjustment will be thrown off.
OPERATION 013145 And then insert the brush all the way into the groove of the dust cover by using slotted driver or other appropriate tool. 010273 Always use the top grip (auxiliary handle) and firmly hold the tool by top grip and switch handle during operations. Dust bag Planing in corners For PC5000C Flush planing of corners is possible after first removing the dust cover cap. For PC5001C only 1. Dust bag 1 1. Dust cover cap 2. The whole roller holder 3. Hex socket head bolt 4.
Replacing carbon brushes 1. Limit mark 1 001145 Remove and check the carbon brushes regularly. Replace when they wear down to the limit mark. Keep the carbon brushes clean and free to slip in the holders. Both carbon brushes should be replaced at the same time. Use only identical carbon brushes. Use a screwdriver to remove the brush holder caps. Take out the worn carbon brushes, insert the new ones and secure the brush holder caps. 1. Brush holder cap 2.
Makita Corporation Anjo, Aichi, Japan 884876E227 12 www.makita.
