82 mm (3-1/4") MODEL Mi02 INSTRUCTION MANUAL DOUBLE INSULATION SPEC IFICAT IONS Planing width 1 Planing depth 8 2 m m (3-114") 1 1 mm (1/32"1 1 No loadspeed (RPM) i 16,000 Overall length 295 m m I 1 1 518") * Manufacturer reserves the right t o change specifications w i t h o u t notice * Note Specifications may differ from country t o country 1 Net weight 2 5 k g ( 5 5 lbsi
IMPORTANT SAFETY INSTRUCTIONS (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PERSONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. 1. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. 2. CONSIDER WORK AREA ENVIRONMENT. Don't use power tools in damp or wet locations. Keep work area well lit. Don't expose power tools t o rain.
14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking t o see that keys and adjusting wrenches are removed f r o m tool before turning it on. 15. AVOID UNINTENTIONAL STARTING. Don‘t carry plugged-in tool with finger on switch. Be sure switch is OFF when plugging in. 16. OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only extension cords intended for use outdoors and so marked. 17. STAY ALERT. Watch what you are doing, use common sense. Don’t operate tool when you are tired. 18.
ADDITIONAL SAFETY RULES 1. Rags, cloth, cord, string and the like should never be left around the work area. 2. Avoid cutting nails. Inspect for and remove all nails from the workpiece before operation. 3. Handle the blades very carefully. 4.Be sure the blade installation bolts are securely tightened before operation. 5. Hold the tool firmly with both hands. 6. Keep hands away from rotating parts. 7. Before using the tool o n an actual workpiece, let it run for a while.
Removing or installing mini planer blades CAUTION : Always be sure that the tool i s switched off and unplugged before removing or installing the blade. To remove the blade, loosen the three installation bolts with the socket wrench. Remove the blade by carefully sliding it from on the end of the drum. WARNING: Be extremely careful not to be cut by the sharp edges. To install the blade, slide it inward from the end of the drum into the gap between the drum and the set plate.
NOTE : A mini planer blade has a cutting edge on both sides, making it reversible for double blade life and greater convenience. CAUTION : Tighten the blade installation bolts carefully when attaching the blades to the tool. A loose installation bolt can be dangerous. Always check to see they are tightened securely. Blade adjustment using blade gauge Unscrew the three installation bolts. Remove the drum cover, the mini blade and the adjusting plate/set plate. Loosen the two screws on the adjusting plate.
For the correct planer blade setting Your planing surface will end up rough and uneven, unless the blade is set properly and securely. The blade must be mounted so that the cutting edge is absolutely level, that is, parallel to the surface of the reat base. Below are some examples of proper and improper settings.
Planing operation First, rest the tool front base flat upon the workpiece surface without the blades making any contact. Switch on and wait until the blades attain full speed. Then move the tool gently forward. Apply pressure on the front of tool a t the start of planing, and a t the back a t the end of planing. Planing will be easier if you incline the workpiece in stationary fashion, so that you can plane somewhat downhill. The speed and depth of cut determine the kind of finish.
You may wish to add to the length of the fence by attaching an extra piece of wood. Convenient holes are provided in the fence for this purpose, and also for attaching an extension guide (optional accessory). I I NOTE : When planing, move the tool with the edge fence flush with the side of the workpiece. Otherwise uneven planing may result. Max. shiplapping depth is 9 mm ( 1 1/32").
ACCESSORI ES CAUTION : These accessories or attachments are recommended for use w i t h your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury t o persons. The accessories or attachments should be used only in the proper and intended manner. 0 Planer blade Part No. 793209-0 0 Guide rule Part No. 191455-1 0 Dust bag assembly Part No. 122269-7 0 Screwdriver Part No. 783002-8 0 Blade gauge Part No. 41 1175-4 0 Socket wrench Part No.
Sep -17 -'87 US 82 mm (3-1/4") POWER PLANER Model MI02 Note The switch, noise suppressor and other part configurations may differ from country to country 11
Sep.