ENGLISH (Original instructions) INSTRUCTION MANUAL Rotary Hammer HR3200C HR3210C HR3210FCT 008536 DOUBLE INSULATION IMPORTANT: Read Before Using.
ENGLISH (Original instructions) SPECIFICATIONS Model Concrete HR3200C HR3210C Tungsten-carbide tipped bit Capacities HR3210FCT 32 mm Core bit 90 mm Steel 13 mm Wood 32 mm No load speed (min-1) 315 - 630 Blows per minute 1,650 - 3,300 Overall length 398 mm Net weight 4.8 kg 424 mm 5.2 kg Safety class 5.4 kg /II • Due to our continuing programme of research and development, the specifications herein are subject to change without notice.
The technical documentation is kept by our authorised representative in Europe who is: Makita International Europe Ltd. Michigan Drive, Tongwell, Milton Keynes, MK15 8JD, England Work mode : chiseling Vibration emission (ah,CHeq) : 7.5 m/s2 Uncertainty (K) : 1.5 m/s2 Work mode: drilling into metal Vibration emission (ah,D) : 2.5 m/s2 or less Uncertainty (K) : 1.5 m/s2 30.1.2009 Model HR3210FCT Work mode : hammer drilling into concrete Vibration emission (ah,HD) : 10.0 m/s2 Uncertainty (K) : 1.
power tool will do the job better and safer at the rate for which it was designed. 19. Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired. 20. Disconnect the plug from the power source and/or the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally. 21.
4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. operator an electric shock. Wear a hard hat (safety helmet), safety glasses and/or face shield. Ordinary eye or sun glasses are NOT safety glasses. It is also highly recommended that you wear a dust mask and thickly padded gloves. Be sure the bit is secured in place before operation. Under normal operation, the tool is designed to produce vibration. The screws can come loose easily, causing a breakdown or accident.
cover pulled in that direction, hold the chuck cover with the index finger. While holding the chuck cover so, pull out the quick change chuck for SDS-plus in the direction of arrow 2 at a stroke. Attaching the quick change drill chuck Speed change 1. Adjusting dial 1. Spindle 2. Quick change drill chuck 3. Change cover 1 1 3 2 008538 The revolutions and blows per minute can be adjusted just by turning the adjusting dial. The dial is marked 1 (lowest speed) to 5 (full speed).
Hammering only ASSEMBLY 1. Pointer 2. Change lever 3. Lock button 1 • CAUTION: Always be sure that the tool is switched off and unplugged before carrying out any work on the tool. Side grip 2 1 3 1. Side grip 008539 For chipping, scaling or demolition operations, depress the lock button and rotate the change lever so that the pointer points to the symbol. Use a bull point, cold chisel, scaling chisel, etc. • • CAUTION: Do not rotate the change lever when the tool is running under load.
To remove the bit, pull the chuck cover down all the way and pull the bit out. Dust cup 1. Dust cup 1. Bit 2. Chuck cover 1 1 2 001300 008544 Use the dust cup to prevent dust from falling over the tool and on yourself when performing overhead drilling operations. Attach the dust cup to the bit as shown in the figure. The size of bits which the dust cup can be attached to is as follows. Bit angle (when chipping, scaling or demolishing) 1. Change lever 2. Lock button 3.
tool firmly with both hands to prevent dangerous reaction. 1 Blow-out bulb (optional accessory) 1. Sleeve 2. Ring 2 1. Blow-out bulb 1 008553 For Model HR3200C,HR3210C Use the optional drill chuck assembly. When installing it, refer to "Installing or removing the bit" described on the previous page. Set the change lever so that the pointer points to the symbol. For Model HR3210FCT Use the quick change drill chuck as standard equipment.
MAINTENANCE • • 1. Screws CAUTION: Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance. Never use gasoline, benzine, thinner, alcohol or the like. Discoloration, deformation or cracks may result. 1 008603 Align the change lever with the symbol , loosen the five screws and then remove the crank cap. Lubrication CAUTION: This servicing should be performed by Makita Authorized or Factory Service Centers only.
• • CAUTION: Do not tighten the crank cap excessively. It is made of resin and is subject to breakage. 1. Connector 1 008606 Connect the connector firmly and then reinstall the handle. CAUTION: Be careful not to damage the connector or lead wires especially when installing the handle.
Makita Corporation Anjo, Aichi, Japan 884769B228 12 www.makita.
