ENGLISH (Original instructions) INSTRUCTION MANUAL Rotary Hammer / Combination Hammer HR2300 HR2310T HR2600 HR2601 HR2610 HR2610T HR2611F HR2611FT 010712 DOUBLE INSULATION IMPORTANT: Read Before Using.
ENGLISH (Original instructions) SPECIFICATIONS Model HR2300 Concrete Capacities HR2310T HR2600 HR2601 HR2610 23 mm HR2610T HR2611F HR2611FT 26 mm Core bit 68 mm 68 mm 68 mm Diamond core bit (dry type) 70 mm 80 mm 80 mm Steel 13 mm 13 mm 13 mm Wood 32 mm 32 mm 32 mm No load speed (min-1) 0 - 1,200 Blows per minute 0 - 4,600 Overall length 356 mm 380 mm Net weight 2.7 kg 2.9 kg 361 mm 2.8 kg Safety class 2.9 kg 2.8 kg 385 mm 361 mm 385 mm 2.9 kg 2.9 kg 3.
Power tool use and care 18. Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed. 19. Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired. 20.
. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. wiring or its own cord. Cutting accessory contacting a "live" wire may make exposed metal parts of the power tool "live" and could give the operator an electric shock. Wear a hard hat (safety helmet), safety glasses and/or face shield. Ordinary eye or sun glasses are NOT safety glasses. It is also highly recommended that you wear a dust mask and thickly padded gloves. Be sure the bit is secured in place before operation.
Attaching the quick change drill chuck Reversing switch action B 1. Reversing switch lever 1. Spindle 2. Quick change drill chuck 3. Change cover line 4. Change cover 1 2 A 1 3 4 011562 010722 Check the line of the quick change drill chuck shows the symbol. Grasp the change cover of the quick change drill chuck and set the line to the symbol. Place the quick change drill chuck on the spindle of the tool.
For Models HR2310T, HR2610, HR2610T, HR2611F, HR2611FT Rotation with hammering 1 symbol position. At may no longer move in the this time, turn the tool on or turn the chuck by hand in the symbol position and then rotate the action mode changing knob. Forcing the action mode changing knob may cause tool damage. 1. Rotation with hammering 2. Action mode changing knob Torque limiter The torque limiter will actuate when a certain torque level is reached. The motor will disengage from the output shaft.
The bit can be secured at the desired angle. To change the bit angle, rotate the action mode changing knob to the O symbol. Turn the bit to the desired angle. Rotate the action mode changing knob to the symbol. Then make sure that the bit is securely held in place by turning it slightly. Installing or removing the bit 1. Bit shank 2. Bit grease 2 1 003150 Clean the bit shank and apply bit grease before installing the bit. 1.
Installing or removing the dust cup 1. Lock button 1 1 2 1. symbol 2. Grooves 3. Dust cup 3 010718 Adjust the depth gauge to the desired depth by moving it back and forth while pressing the lock button. After the adjustment, release the lock button to lock the depth gauge. 2 1 011506 Before installing the dust cup, remove the bit from the tool if installed on the tool. Install the dust cup (accessory) on the tool so that the symbol on the dust cup is aligned with the grooves in the tool. 1.
OPERATION 1. Inside periphery 2. Carved side 3. Attachment 4. Cap 5. Groove 1 2 4 Always use the side grip (auxiliary handle) and firmly hold the tool by both side grip and switch handle during operations. Hammer drilling operation 3 5 012895 1. Cap 2. Attachment 1 010729 Set the action mode changing knob to the symbol. Position the bit at the desired location for the hole, then pull the switch trigger. Do not force the tool. Light pressure gives best results.
After drilling the hole, use the blow-out bulb to clean the dust out of the hole. Chipping/Scaling/Demolition 2 1. Spindle 2. Quick change drill chuck 3. Change cover line 4. Change cover 1 For Models HR2310T, HR2610, HR2610T, HR2611F, HR2611FT 3 4 011562 Use the quick change drill chuck as standard equipment. When installing it, refer to "changing the quick change chuck for SDS-plus " described on the previous page. 1. Sleeve 2. Ring 3.
Diamond core drilling OPTIONAL ACCESSORIES When performing diamond core drilling operations, always set the change lever to the position to use "rotation only" action. CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose.
Makita Corporation 884939A3 12 www.makita.