ENGLISH (Original instructions) INSTRUCTION MANUAL Rotary Hammer HR2470 HR2470F HR2470FT HR2470T 007943 DOUBLE INSULATION WARNING: For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
ENGLISH (Original instructions) SPECIFICATIONS Model HR2470/HR2470F 24 mm Core bit 54 mm Diamond core bit (dry type) 65 mm Concrete Capacities HR2470T/HR2470FT Tungsten-carbide tipped bit Steel 13 mm Wood 32 mm No load speed (min-1) 0 - 1,100 Blows per minute 0 - 4,500 Overall length 370 mm Net weight 2.9 kg Safety class 394 mm 3.0 kg /II • Due to our continuing programme of research and development, the specifications herein are subject to change without notice.
• Be sure to identify safety measures to protect the operator that are based on an estimation of exposure in the actual conditions of use (taking account of all parts of the operating cycle such as the times when the tool is switched off and when it is running idle in addition to the trigger time). Work area safety 1. Keep work area clean and well lit. Cluttered or dark areas invite accidents. 2.
13. Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury. 14. Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations. 15. Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing, and gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts. 16.
supplier safety data. CAUTION: Do not look in the light or see the source of light directly. To turn on the lamp, pull the trigger. Release the trigger to turn it off. • SAVE THESE INSTRUCTIONS. WARNING: DO NOT let comfort or familiarity with product (gained from repeated use) replace strict adherence to safety rules for the subject product. MISUSE or failure to follow the safety rules stated in this instruction manual may cause serious personal injury.
For drilling in wood, metal or plastic materials, depress the lock button and rotate the action mode changing knob to the symbol. Use a twist drill bit or wood bit. Hammering only CAUTION: Before removing the quick change chuck for SDS-plus, always remove the bit. Grasp the change cover of the quick change chuck for SDS-plus and turn in the direction of the arrow until the change cover line moves from the symbol to the symbol. Pull forcefully in the direction of the arrow.
Side grip (auxiliary handle) 1 6 3 4 2 5 To remove the bit, pull the chuck cover down all the way and pull the bit out. 1. Grip base 2. Side grip 3. Loosen 4. Tighten 5. Teeth 6. Protrusion 1. Bit 2. Chuck cover 1 2 007949 007939 CAUTION: • Always use the side grip to ensure operating safety. Install the side grip so that the teeth on the grip fit in between the protrusions on the tool barrel. Then tighten the grip by turning clockwise at the desired position.
and normal drilling may be resumed. The depth gauge is convenient for drilling holes of uniform depth. Loosen the side grip and insert the depth gauge into the hole in the side grip. Adjust the depth gauge to the desired depth and tighten the side grip. • NOTE: • The depth gauge cannot be used at the position where the depth gauge strikes against the gear housing. Dust cup 1.
Drilling in wood or metal clockwise to tighten the chuck. To remove the bit, hold the ring and turn the sleeve counterclockwise. Set the action mode changing knob to the symbol. You can drill up to 13 mm diameter in metal and up to 32 mm diameter in wood. 1. Chuck adapter 2. Keyless drill chuck 1 • 2 004223 1. Quick change chuck for SDS-plus 2. Change cover line 3. Change cover 1 2 • • 3 007944 • 2 1. Spindle 2. Quick change drill chuck 3. Change cover line 4.
ACCESSORIES CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose. If you need any assistance for more details regarding these accessories, ask your local Makita Service Center.
Makita Corporation Anjo, Aichi, Japan 884704C226 12