GB Rotary Hammer / Combination Hammer Instruction Manual F Marteau Perforateur / Marteau combi Manuel d’instructions D Bohrhammer / Kombi-Hammer Betriebsanleitung I Martello rotativo / Martello multifunzione Istruzioni per l’uso NL Boorhamer / Combinatiehamer Gebruiksaanwijzing E Martillo Rotativo / Martillo Rotativo Combinado Manual de instrucciones P Martelo Rotativo / Martele Combinado Manual de instruções DK Borehammer / Kombinationshammer Brugsanvisning GR Περιστροφικ σφυρί / Σφυρί
1 2 3 1 2 5 B A 4 6 3 4 10 8 9 6 5 7 11 12 6 10 12 7 2 11 8 7
14 15 13 9 10 17 16 18 11 12 18 19 12 13 14 20 2 21 15 16 3
2 22 23 17 18 23 24 22 19 20 25 15 18 19 24 21 22 26 27 28 23 4 24
30 29 30 31 32 28 28 25 26 27 28 33 29 30 5 34 35 31 6 7 32 5
36 8 9 37 7 6 33 34 24 35 6 9
ENGLISH (Original instructions) Explanation of general view 1 2 3 4 5 6 7 8 9 10 11 12 13 Switch trigger Lock button Lamp Reversing switch lever Quick change chuck for SDSplus Change cover line Change cover Spindle Quick change drill chuck Rotation with hammering Rotation only Action mode changing knob Hammering only 14 15 16 17 18 19 20 21 22 Protrusions Grooves Bit shank Bit grease Bit Chuck cover Grip base Depth gauge Toothed side of hex hole marking on the grip base 23 Toothed side of the depth gauge
7. 8. 9. 10. 11. 12. 13. 14. In cold weather or when the tool has not been used for a long time, let the tool warm up for a while by operating it under no load. This will loosen up the lubrication. Without proper warm up, hammering operation is difficult. Always be sure you have a firm footing. Be sure no one is below when using the tool in high locations. Hold the tool firmly with both hands. Keep hands away from moving parts. Do not leave the tool running. Operate the tool only when hand-held.
Hammering only (Fig. 9) For chipping, scaling or demolition operations, rotate the action mode changing knob to the g symbol. Use a bull point, cold chisel, scaling chisel, etc. CAUTION: • Do not rotate the action mode changing knob when the tool is running under load. The tool will be damaged. • To avoid rapid wear on the mode change mechanism, be sure that the action mode changing knob is always positively located in one of the three action mode positions.
NOTE: • If you connect a vacuum cleaner to your hammer, cleaner operations can be performed. Dust cap needs to be removed from the dust cup before the connection. (Fig. 27) OPERATION Always use the side grip (auxiliary handle) and firmly hold the tool by both side grip and switch handle during operations. Hammer drilling operation (Fig. 28) Set the action mode changing knob to the symbol. Position the bit at the desired location for the hole, then pull the switch trigger. Do not force the tool.
MAINTENANCE ENG900-1 CAUTION: • Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance. • Never use gasoline, benzine, thinner, alcohol or the like. Discoloration, deformation or cracks may result. To maintain product SAFETY and RELIABILITY, repairs, carbon brush inspection and replacement, any other maintenance or adjustment should be performed by Makita Authorized Service Centers, always using Makita replacement parts.
Model HR2611FT Work mode: hammer drilling into concrete Vibration emission (ah, HD): 11.5 m/s2 Uncertainty (K): 1.5 m/s2 ENH101-15 For European countries only EC Declaration of Conformity Work mode: chiseling function with side grip Vibration emission (ah, CHeq): 8.5 m/s2 Uncertainty (K): 1.5 m/s2 Work mode: drilling into metal Vibration emission (ah, D): 2.5 m/s2 or less Uncertainty (K): 1.
NEDERLANDS (Originele instructies) Verklaring van algemene gegevens 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Aan/uit-schakelaar Vergrendelknop Lampje Omkeerschakelaar Snelwisselkop voor SDS-plus Streep op wisselmof Wisselmof As Snelwisselboorkop Ronddraaien met hameren Alleen ronddraaien Werkingsfunctie-keuzeknop Alleen hameren Uitsteeksels 15 16 17 18 19 20 21 22 Groeven Boorschacht Boorvet Boor Boorkopmof Basis van de zijhandgreep Diepteaanslag Getande kant van de zeskantgatmarkering op de basis van de zijhand
3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. Houd elektrisch gereedschap vast aan het geïsoleerde oppervlak van de handgrepen wanneer u werkt op plaatsen waar het booraccessoire met verborgen bedrading of zijn eigen snoer in aanraking kan komen. Wanneer het booraccessoire in aanraking komen met onder spanning staande draden, zullen de niet-geïsoleerde metalen delen van het gereedschap onder spanning komt te staan zodat de gebruiker een elektrische schok kan krijgen.
De snelwisselkop voor SDS-plus vervangen Voor modellen HR2310T, HR2610T en HR2611FT De snelwisselkop voor SDS-plus kan eenvoudig worden vervangen door de snelwisselboorkop. De snelwisselkop voor SDS-plus verwijderen (Fig. 4) LET OP: • Haal altijd de boor eruit voordat u de snelwisselkop voor SDS-plus verwijdert. • Als u de knop van het symbool g naar het symbool m draait, is het mogelijk dat de werkingsfunctie-keuzewilt draaien.
Boorhoek (bij beitelen, bikken of slopen) Voor modellen HR2310T, HR2610, HR2610T, HR2611F en HR2611FT De boor kan onder de gewenste hoek worden vastgezet. Om de boorhoek te veranderen, draait u de werkingsfunctie-keuzeknop naar het symbool O. Draai de boor naar de gewenste hoek. (Fig. 14) Draai de werkingsfunctie-keuzeknop naar het symbool g. (Fig. 15) Controleer daarna of de boor stevig op zijn plaats vastzit door deze iets te verdraaien.
Boren in hout of metaal Voor modellen HR2300, HR2600, HR2601, HR2610 en HR2611F Gebruik de los verkrijgbare complete boorkop. Om deze aan te brengen, zie “Aanbrengen en verwijderen van de boor” op de vorige pagina. (Fig. 31) Voor modellen HR2310T, HR2610T en HR2611FT Gebruik de snelwisselboorkop als standaarduitrusting. Om deze aan te brengen, zie “De snelwisselkop voor SDS-plus vervangen” op de vorige pagina. (Fig.
ENG905-1 Geluid De typische, A-gewogen geluidsniveaus zijn gemeten volgens EN60745: Model HR2300, HR2601, HR2611F, HR2611FT Geluidsdrukniveau (LpA): 90 dB (A) Geluidsvermogenniveau (LWA): 101 dB (A) Onnauwkeurigheid (K): 3 dB (A) Model HR2310T, HR2600, HR2610, HR2610T Geluidsdrukniveau (LpA): 91 dB (A) Geluidsvermogenniveau (LWA): 102 dB (A) Onnauwkeurigheid (K): 3 dB (A) Draag gehoorbescherming ENG900-1 Trillingen De totale trillingswaarde (triaxiale vectorsom) zoals vastgesteld volgens EN60745: Model HR
ENH101-15 Alleen voor Europese landen ENH101-15 Alleen voor Europese landen EU-verklaring van conformiteit EU-verklaring van conformiteit Wij, Makita Corporation, als de verantwoordelijke fabrikant, verklaren dat de volgende Makitamachine(s): Aanduiding van de machine: Boorhamer Modelnr.